GLS85LS1008P-S-I-FZJE - Greenliant Systems

Factsheet 04.100

July 2018

These specifications are subject to change without notice. 07/10/2018

GLS85LS1002P / 1004P / 1008P

Industrial Grade

SATA NAND rive

™

Features

• Industry Standard Serial ATA (SATA) Host

Interface

- SATA 1.5Gb/s 1)

- ATA/ATAPI-8 compliant

- Supports 48-bit addr es s feature set

• Performance

- Sequential data read:

Up to 70 MByte/sec*

- Sequential data write:

Up to 60 MByte/sec *

* measured using 128 KByte transfer size

• Power Management

- 3.3V and 1.2Vpower supply

- Host SATA interface power management

- Immediate dis ab ling of unused circuitry

without host intervention

• Power Spe cifications 2)

- Active mode:

750mW typical (GLS85LS1008P)

560mW typical (GLS85LS1004P)

450mW typical (GLS85LS1002P)

- Idle / Standby mode: 210mW ty pi c al

- Sleep mode: 70mW typical

• Integrated Voltage Detector

- Detects supply voltage fluctuations and

generates reset during power-up and power-

down to prevent inadvertent writes

• Supports SMART Commands

• Expanded Data Protection

- Added data security through user-selectable

protection zo nes

• 20-Byte Serial Nu mber

- Factory pre-programmed 10-Byte unique ID

- User-programmable 10-Byte ID

• Robust Built-in ECC

• NAND Configu ration

- 1 bit per cell (SLC)

• Industrial Temperature Range

- -40°C to 85°C

• FBGA package

- 14.0 mm x 24.0 mm x 1.95 mm, 145-ball,

1.0 mm ball pitch, FZJE

• All Devices are RoHS Compliant

1) Current product revision supports SATA Revision 1.x with

host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5Gb/s).

2) For management of the Sleep Mode, refer to “SATA

NANDrive Applicat i on Design Guide.”

Product Description

The GLS85L S10 02 P / 100 4P / 10 08P Industrial Grade

SATA NANDrive™ devices (referred to as “SATA

NANDrive” in this factsheet) are fully integrated solid

state drives. They combine an advanced Greenliant

NAND controller and 2, 4 or 8 GByte of NAND flas h in

a multi-chip package. These products are ideal for

embedded and portable applications that require

smaller form-factor and more reliable data storage.

SATA-int erfac e sol id state m ass s torage tech nolog y is

widely used in portable and industrial computers, set-

top boxes, multi-functional printers, point-of-sales

terminals, video and audio recorders, medical

instruments and car infotainment systems.

SATA NANDrive is a single device, solid state drive

(SSD) that provides the functionality and compatibility

of a com plete SAT A har d di sk dr ive (HDD) in a 14 m m

x 24 mm BGA package for easy, space saving

mounting to a system motherboard. These products

surpass tradition al st orage in their s m all si ze, secur ity,

reliability, ruggedness and low power consumption.

The integrated NAND flash controller with built-in

advanced NAND management firmware

communicates with the host through the standard

SATA protocol. It does not require any additional or

proprietary software such as the Flash File System

(FFS) and Memory Technology Driver (MTD).

SATA NANDrive is pre-programmed with a 10-Byte

unique serial ID and has the option of programming

an additional 10-Byte serial ID for even greater

system security.

SATA NANDrive’s advanced NAND management

technology enhances data reliability and security,

improves endurance and accurately estimates the

remaining life of the NAND flash devices. This

innovative technology combines robust NAND

controller hardware error correction capabilities with

advanced wear-leveling algorithms and bad block

management to significantly extend the life of the

product.

SATA NANDrive devices are offered in a 145-ball

BGA, 1 mm ball pitch package.

Factsheet 04.100

July 2018

These specifications are subject to change without notice. 07/10/2018

GLS85LS1002P / 1004P / 1008P

Industrial Grade

SATA NAND rive

™

1.0 GENERAL DESCRIPTION

Each SATA NANDrive contains an integrated SATA NAND flash memory controller and up to eight discrete

NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram.

1.1 Optimized SATA NANDrive

The heart o f SATA NANDri ve is th e SATA NAND f las h

memory controller which translates standard SATA

signals into flash media data and control signals. The

following components contribute to SATA NANDrive’s

operation.

1.1.1 Microcontroller Unit (MCU)

The MCU translates SATA commands into data and

control signals required for flash media operation.

1.1.2 Internal Direct Memory Access (DMA)

SATA NANDrive uses internal DMA allowing instant

data transfer from/to buffer to/from flash media. This

implementation eliminates microcontroller overhead

associated with the traditional, firmware-based

approach, thereby increasing the data transfer rate.

1.1.3 Power Management Unit (PMU)

The PMU controls the power consumption of SATA

NANDrive. The PMU dramatically reduces the power

consum ption of SATA NAN Drive b y putting the par t of

the circuitry that is not in operation into sleep mode. 3)

The Flash File System handles inadvertent power

interrupts and has auto-recovery capability to ensure

SATA NANDrive firmware integrity. For regular power

management, the host must send a

STANDBY_IMMEDIATE (E0h), IDLE_IMMEDIATE

(E1h), STANDBY (E2h) or IDLE (E3h) command and

wait for comm and ready before powering do wn SAT A

NANDrive.

3) For management of the Sleep Mode, refer to “SATA

NANDrive Applicat i on Design Guide.”

1.1.4 Embedded Flash File System

The embedded flash file system is an integral part of

SATA NANDrive. It contains MCU firmware that

performs the following tasks:

1. Translates host side signals into flash media

writes and reads

2. Provides flash media wear leveling to spread the

flash writes across all memory address space to

increase the longevity of flash media

3. Keeps track of data file structures

4. Manages system security for the selected

protection zo nes

1.1.5 Error Correction Code (ECC)

High performance is achieved through optimized

hardware error detection and correction.

1.1.6 Serial Communication Interface (SCI)

The Seria l Comm unication Inter face (SCI) is desi gned

for error reporting. During the product development

stage, it is recommended to provide the SCI port on

the PCB to aid in design validation.

1.1.7 Multi-tas king Interface

The multi-tasking interface enables fast, sequential

write performance by allowing concurrent Read,

Program and Erase operati ons to m ultiple flash m edia.

1.2 SMT Reflow Consideration

The SATA NANDrive family utilizes standard NAND

flash for data storage. Because the high temperature

in a surface-mount solder ing ref low process may alter

the content on NAND flash, it is recommended to

program SATA NANDrive after the reflow process.

1.3 Advanced NAND Management

SATA NANDrive’s integrated controller uses

advanced wear-leveling algorithms to substantially

increase the longevity of NAND flash media. Wear

caused by data writes is evenly distributed in all or

select bloc ks in the device that pre vents “hot spots ” in

locations th at are pr o gram med and erased ex tensively.

This effective wear-leveling technique results in

optimized device endurance, enhanced data retention

and higher reliability required by long-life applications.

Factsheet 04.100

July 2018

These specifications are subject to change without notice. 07/10/2018

GLS85LS1002P / 1004P / 1008P

Industrial Grade

SATA NAND rive

™

2.0 FUNCTIONAL BLOCKS

Figure 2-1: SATA NANDrive Block Diagram

Fla sh Media I/F

NAND I/F

NAND

Chips

NAND

Chips

NAND

Chips

E mbedded Fla sh

File System

MCU

SATA I/F

Internal

DMA

SCI

PMU

Memory

Channel I/F

NAND Controller

ECC

SRAM Buffer

SATA ll

HOS T I/F

3.0/1.5 Gbps

Memory

Channel I/F

ECC

NAND

Chips

NAND

Flash

SAT A NANDrive

Factsheet 04.100

July 2018

These specifications are subject to change without notice. 07/10/2018

GLS85LS1002P / 1004P / 1008P

Industrial Grade

SATA NAND rive

™

3.0 PRODUCT ORDERING INFOR MATION

GLS 85 LS 1 0xxP - S - I - FZJE - NDxxx

XX XX X XXXX - X - X - XXXX - XXXXX

Ordering Code 4)

NDxxx or TTxxx = N ANDrive revision

Exxxx = Evaluation Board revision

Environmental Attribute

E = non-Pb solder (RoHS Compliant)

Package Modifier

ZJ = 145-ball positions

Package Type

F = FBGA

Operation Temperature

I = Industrial: -40°C to +85°C

NAND Configuration

S = 1 bit per cell

Generation / Pro duct Configuration

P = First generation

Capacity

002 = 2 GByte

004 = 4 GByte

008 = 8 GByte

MByte or GByte Designator

0 = MByte

1 = GByte

Interface

S = SATA

Voltage

L = 3.3V

Product Series

85 = NANDrive

4) Note that the top side mark ing on the package typically does not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC

(custom specific ation) which is required by the end-c ust omer to be marked on the device.

Factsheet 04.100

July 2018

These specifications are subject to change without notice. 07/10/2018

GLS85LS1002P / 1004P / 1008P

Industrial Grade

SATA NAND rive

™

Valid Combinations

Valid prod uct combinati ons are thos e that are in the mass production or will be in th e mass produc tion. Consult

your Gr een liant s al es representative to c o nf irm ava i lab ilit y of t he v al id combinatio ns an d t o det er mine availa bility

of new product combinations.

Table 3-1: SATA NANDrive Product Vali d Ordering Numbers

Capacity

Operating Temperature

Part Number

Package

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-FZJE

FZJE, 14x24x1.95mm

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-FZJE-ND104

FZJE, 14x24x1.95mm

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-FZJE-TT095*

FZJE, 14x24x1.95mm

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-FZJE

FZJE, 14x24x1.95mm

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-FZJE-ND104

FZJE, 14x24x1.95mm

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-FZJE-TT095*

FZJE, 14x24x1.95mm

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-FZJE

FZJE, 14x24x1.95mm

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-FZJE-ND101

FZJE, 14x24x1.95mm

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-FZJE-ND104

FZJE, 14x24x1.95mm

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-FZJE-TT095*

FZJE, 14x24x1.95mm

* TT095 products include enhanced support for TRIM command and power management in W i ndows environments .

Table 3-2: SATA NANDrive Evaluation Board Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Form Factor

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-1S-K

Module with SATA connector

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-1S-ED104

Module with SATA connector

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-1S-ET095

Module with SATA connector

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-1S-K

Module with SATA connector

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-1S-ED104

Module with SATA connector

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-1S-ET095

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1S-K

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1S-ED101

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1S-ED104

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1S-ET095

Module with SATA connector

Capacity

Operating Temperature

Part Number

Form Factor

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-1S-K

Module with SATA connector

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-1S-ED104

Module with SATA connector

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-1S-ET095

Module with SATA connector

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-1S-K

Module with SATA connector

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-1S-ED104

Module with SATA connector

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-1S-ET095

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1S-K

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1S-ED101

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1S-ED104

Module with SATA connector

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1S-ET095

Module with SATA connector

Table 3-3: SATA NANDrive miniSATA Evaluation Board Valid Ordering Numbers

Capacity

Operating Temperature

Part Number

Form Factor

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-1MS-K

JEDEC MO -300

Factsheet 04.100

July 2018

These specifications are subject to change without notice. 07/10/2018

GLS85LS1002P / 1004P / 1008P

Industrial Grade

SATA NAND rive

™

2GB

Industrial (-40°C to 85°C)

GLS85LS1002P-S-I-1MS-ED104

JEDEC MO -300

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-1MS-K

JEDEC MO-300

4GB

Industrial (-40°C to 85°C)

GLS85LS1004P-S-I-1MS-ED104

JEDEC MO -300

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1MS-K

JEDEC MO -300

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1MS-ED101

JEDEC MO -300

8GB

Industrial (-40°C to 85°C)

GLS85LS1008P-S-I-1MS-ED104

JEDEC MO -300

Factsheet 04.100

July 2018

These specifications are subject to change without notice. 07/10/2018

GLS85LS1002P / 1004P / 1008P

Industrial Grade

SATA NAND rive

™

3.1 Package Diagram

TOP VIEW

11

10

9

8

7

6

5

4

3

2

1

A B C D E F G H J K L M N P R T U V W Y AA AB AC

24.0 ±0.1

BOTTOM VIEW

1

2

3

4

5

6

7

8

9

10

11

A B C D E F G H J K L M N P R T U V W Y AA AB AC

SIDE

VIEW

1mm

DETAIL

Note: All linear dim ensions are in millimeters.

Untoleranced dim ensi ons are nominal target values.

Coplanarity: 0.15 mm.

0.40 ±0.05 Ball opening size is 0.40 mm (± 0.05 mm).

1.80 ± 0.15

SEATING

PLANE

Figure 3-1: SATA NANDrive 145-Ball, Ball Grid Array (BGA) Greenliant Package Code: FZJ

14.0

+/- 0.1

A1

CORNER

14.0

1.0

8.0

1.0

0.5 +/- 0.05

(145x)

0.15

3.0

Factsheet 04.100

July 2018

These specifications are subject to change without notice. 07/10/2018

GLS85LS1002P / 1004P / 1008P

Industrial Grade

SATA NAND rive

™

Revision History

Revision

Description

Date

01.000

Initial release of Fact Sheet for GLS85LS1002P/1004P/1008P

October 17, 2011

01.001

Updated Table 3-1

December 22, 2011

01.002

Corrected typo in Table 3-1

March 12, 2012

02.000

Added part numbers GLS85LS1016P/1032P and updated Section 1.2

April 9, 2012

02.100

Separated part numbers GLS85LS1016P/1032P to document S71445-F

Updated Table 3-1 and Section 4.0

January 18, 2013

02.101

Removed Table 3-1

April 17, 2013

02.200

Updated Po wer Specifications

Added information for part number GLS85LS1008P-S-I-FZJE-ND104

November 21, 2013

03.000

Added information for part numbers GLS85LS1002P-S-I-FZJE-ND104

and GLS85LS1004P-S-I-FZJE-ND104

February 25, 2014

03.001

Updated Sect ion 1.1. 3

May 09, 2014

04.000

Added GLS85LS1002P/1004P/1008P part numbers with the TT095

suffix

October 19, 2016

04.100

Added Evaluation Board part numbers with the ET095 suffix

July 10, 2018

Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant. All

other trademarks and registered trademarks are the property of their respective owners.

Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable

capacity may be less.

Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant

Terms and Conditions of Sale.

www.greenliant.com