LM7905,LM7912,LM7915
LM79XX Series 3-Terminal Negative Regulators
Literature Number: SNOSBQ7B
LM79XX Series
3-Terminal Negative Regulators
General Description
The LM79XX series of 3-terminal regulators is available with
fixed output voltages of −5V, −12V, and −15V. These devices
need only one external component — a compensation ca-
pacitor at the output. The LM79XX series is packaged in the
TO-220 power package and is capable of supplying 1.5A of
output current.
These regulators employ internal current limiting safe area
protection and thermal shutdown for protection against vir-
tually all overload conditions.
Low ground pin current of the LM79XX series allows output
voltage to be easily boosted above the preset value with a
resistor divider. The low quiescent current drain of these
devices with a specified maximum change with line and load
ensures good regulation in the voltage boosted mode.
For applications requiring other voltages, see LM137
datasheet.
Features
nThermal, short circuit and safe area protection
nHigh ripple rejection
n1.5A output current
n4% tolerance on preset output voltage
Connection Diagram
TO-220 Package
00734014
Front View
Order Number LM7905CT, LM7912CT or LM7915CT
See NS Package Number TO3B
Typical Applications
Fixed Regulator
00734003
*Required if regulator is separated from filter capacitor by
more than 3". For value given, capacitor must be solid
tantalum. 25µF aluminum electrolytic may be substituted.
†Required for stability. For value given, capacitor must be
solid tantalum. 25µF aluminum electrolytic may be substi-
tuted. Values given may be increased without limit.
For output capacitance in excess of 100µF, a high current
diode from input to output (1N4001, etc.) will protect the
regulator from momentary input shorts.
September 2001
LM79XX Series 3-Terminal Negative Regulators
© 2004 National Semiconductor Corporation DS007340 www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Input Voltage
(V
o
= −5V) −25V
(V
o
= −12V and −15V) −35V
Input-Output Differential
(V
o
= −5V) 25V
(V
o
= −12V and −15V) 30V
Power Dissipation (Note 2) Internally Limited
Operating Junction Temperature Range 0˚C to +125˚C
Storage Temperature Range −65˚C to +150˚C
Lead Temperature (Soldering, 10 sec.) 230˚C
Electrical Characteristics
Conditions unless otherwise noted: I
OUT
= 500mA, C
IN
= 2.2µF, C
OUT
= 1µF, 0˚C ≤T
J
≤+125˚C, Power Dissipation ≤1.5W.
Part Number LM7905C Units
Output Voltage −5V
Input Voltage (unless otherwise specified) −10V
Symbol Parameter Conditions Min Typ Max
V
O
Output Voltage T
J
= 25˚C −4.8 −5.0 −5.2 V
5mA ≤I
OUT
≤1A, −4.75 −5.25 V
P≤15W (−20 ≤V
IN
≤−7) V
∆V
O
Line Regulation T
J
= 25˚C, (Note 3) 8 50 mV
(−25 ≤V
IN
≤−7) V
215mV
(−12 ≤V
IN
≤−8) V
∆V
O
Load Regulation T
J
= 25˚C, (Note 3)
5mA ≤I
OUT
≤1.5A 15 100 mV
250mA ≤I
OUT
≤750mA 5 50 mV
I
Q
Quiescent Current T
J
= 25˚C 1 2 mA
∆I
Q
Quiescent Current With Line 0.5 mA
Change (−25 ≤V
IN
≤−7) V
With Load, 5mA ≤I
OUT
≤1A 0.5 mA
V
n
Output Noise Voltage T
A
= 25˚C, 10Hz ≤f≤100Hz 125 µV
Ripple Rejection f = 120Hz 54 66 dB
(−18 ≤V
IN
≤−8) V
Dropout Voltage T
J
= 25˚C, I
OUT
= 1A 1.1 V
I
OMAX
Peak Output Current T
J
= 25˚C 2.2 A
Average Temperature I
OUT
= 5mA, 0.4 mV/˚C
Coefficient of 0 C ≤T
J
≤100˚C
Output Voltage
Electrical Characteristics
Conditions unless otherwise noted: I
OUT
= 500mA, C
IN
= 2.2µF, C
OUT
= 1µF, 0˚C ≤T
J
≤+125˚C, Power Dissipation ≤1.5W.
Part Number LM7912C LM7915C Units
Output Voltage −12V −15V
Input Voltage (unless otherwise specified) −19V −23V
Symbol Parameter Conditions Min Typ Max Min Typ Max
V
O
Output Voltage T
J
= 25˚C −11.5 −12.0 −12.5 −14.4 −15.0 −15.6 V
5mA ≤I
OUT
≤1A, −11.4 −12.6 −14.25 −15.75 V
P≤15W (−27 ≤V
IN
≤−14.5) (−30 ≤V
IN
≤−17.5) V
∆V
O
Line Regulation T
J
= 25˚C, (Note 3) 5 80 5 100 mV
(−30 ≤V
IN
≤−14.5) (−30 ≤V
IN
≤−17.5) V
3 30 3 50 mV
(−22 ≤V
IN
≤−16) (−26 ≤V
IN
≤−20) V
LM79XX Series
www.national.com 2
Electrical Characteristics (Continued)
Conditions unless otherwise noted: I
OUT
= 500mA, C
IN
= 2.2µF, C
OUT
= 1µF, 0˚C ≤T
J
≤+125˚C, Power Dissipation ≤1.5W.
Part Number LM7912C LM7915C Units
Output Voltage −12V −15V
Input Voltage (unless otherwise specified) −19V −23V
Symbol Parameter Conditions Min Typ Max Min Typ Max
∆V
O
Load Regulation T
J
= 25˚C, (Note 3)
5mA ≤I
OUT
≤1.5A 15 200 15 200 mV
250mA ≤I
OUT
≤750mA 5 75 5 75 mV
I
Q
Quiescent Current T
J
= 25˚C 1.5 3 1.5 3 mA
∆I
Q
Quiescent Current With Line 0.5 0.5 mA
Change (−30 ≤V
IN
≤−14.5) (−30 ≤V
IN
≤−17.5) V
With Load, 5mA ≤I
OUT
≤1A 0.5 0.5 mA
V
n
Output Noise Voltage T
A
= 25˚C, 10Hz ≤f≤100Hz 300 375 µV
Ripple Rejection f = 120 Hz 54 70 54 70 dB
(−25 ≤V
IN
≤−15) (−30 ≤V
IN
≤−17.5) V
Dropout Voltage T
J
= 25˚C, I
OUT
= 1A 1.1 1.1 V
I
OMAX
Peak Output Current T
J
= 25˚C 2.2 2.2 A
Average Temperature I
OUT
= 5mA, −0.8 −1.0 mV/˚C
Coefficient of 0 C ≤T
J
≤100˚C
Output Voltage
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but do not guarantee Specific Performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: Refer to Typical Performance Characteristics and Design Considerations for details.
Note 3: Regulation is measured at a constant junction temperature by pulse testing with a low duty cycle. Changes in output voltage due to heating effects must
be taken into account.
Design Considerations
The LM79XX fixed voltage regulator series has thermal
overload protection from excessive power dissipation, inter-
nal short circuit protection which limits the circuit’s maximum
current, and output transistor safe-area compensation for
reducing the output current as the voltage across the pass
transistor is increased.
Although the internal power dissipation is limited, the junc-
tion temperature must be kept below the maximum specified
temperature (125˚C) in order to meet data sheet specifica-
tions. To calculate the maximum junction temperature or
heat sink required, the following thermal resistance values
should be used:
Typ Max Typ Max
Package θ
JC
θ
JC
θ
JA
θ
JA
˚C/W ˚C/W ˚C/W ˚C/W
TO-220 3.0 5.0 60 40
Solving for T
J
:
T
J
=T
A
+P
D
(θ
JC
+θ
CA
)or
=T
A
+P
D
θ
JA
(without heat sink)
Where:
T
J
= Junction Temperature
T
A
= Ambient Temperature
P
D
= Power Dissipation
θ
JA
= Junction-to-Ambient Thermal Resistance
θ
JC
= Junction-to-Case Thermal Resistance
θ
CA
= Case-to-Ambient Thermal Resistance
θ
CS
= Case-to-Heat Sink Thermal Resistance
θ
SA
= Heat Sink-to-Ambient Thermal Resistance
LM79XX Series
www.national.com3
Typical Applications
Bypass capacitors are necessary for stable operation of the
LM79XX series of regulators over the input voltage and
output current ranges. Output bypass capacitors will improve
the transient response by the regulator.
The bypass capacitors, (2.2µF on the input, 1.0µF on the
output) should be ceramic or solid tantalum which have good
high frequency characteristics. If aluminum electrolytics are
used, their values should be 10µF or larger. The bypass
capacitors should be mounted with the shortest leads, and if
possible, directly across the regulator terminals.
High Stability 1 Amp Regulator
00734005
Load and line regulation <0.01% temperature stability ≤0.2%
†Determine Zener current
††Solid tantalum
*Select resistors to set output voltage. 2 ppm/˚C tracking suggested
Current Source
00734007
LM79XX Series
www.national.com 4
Typical Applications (Continued)
Light Controller Using Silicon Photo Cell
00734008
*Lamp brightness increase until iI=i
Q(≈1 mA) + 5V/R1.
†Necessary only if raw supply filter capacitor is more that 2" from LM7905CT
High-Sensitivity Light Controller
00734009
*Lamp brightness increases until ii= 5V/R1 (Iican be set as low as 1 µA)
†Necessary only if raw supply filter capacitor is more that 2" from LM7905
Variable Output
00734002
*Improves transient response and ripple rejection. Do not increase beyond 50 µF.
Select R2 as follows:
LM7905CT 300Ω
LM7912CT 750Ω
LM7915CT 1k
LM79XX Series
www.national.com5
Typical Applications (Continued)
±15V, 1 Amp Tracking Regulators
00734001
(-15) (+15)
Load Regulation at ∆I
L
= 1A 40mV 2mV
Output Ripple, C
IN
= 3000µF, I
L
= 1A 100 µVms 100 µVms
Temperature Stability 50mV 50mV
Output Noise 10Hz ≤f≤10kHz 150 µVms 150 µVms
*Resistor tolerance of R4 and R5 determine matching of (+) and (−) outputs.
**Necessary only if raw supply filter capacitors are more than 3" from regulators.
Dual Trimmed Supply
00734004
LM79XX Series
www.national.com 6
Schematic Diagrams
−5V
00734012
−12V and −15V
00734013
LM79XX Series
www.national.com7
Physical Dimensions inches (millimeters)
unless otherwise noted
TO-220 Outline Package (T)
Order Number LM7905CT, LM7912CT or LM7915CT
NS Package Number T03B
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned
Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
LM79XX Series 3-Terminal Negative Regulators
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
