LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
LM111-N/LM211-N/LM311-N Voltage Comparator
Check for Samples: LM111-N,LM211-N,LM311-N
Both the inputs and the outputs of the LM111-N,
1FEATURES LM211-N or the LM311-N can be isolated from
2 Operates From Single 5V Supply system ground, and the output can drive loads
Input Current: 150 nA Max. Over Temperature referred to ground, the positive supply or the negative
supply. Offset balancing and strobe capability are
Offset Current: 20 nA Max. Over Temperature provided and outputs can be wire OR'ed. Although
Differential Input Voltage Range: ±30V slower than the LM106 and LM710 (200 ns response
Power Consumption: 135 mW at ±15V time vs 40 ns) the devices are also much less prone
to spurious oscillations. The LM111-N has the same
DESCRIPTION pin configuration as the LM106 and LM710.
The LM111-N, LM211-N and LM311-N are voltage The LM211-N is identical to the LM111-N, except that
comparators that have input currents nearly a its performance is specified over a 25°C to +85°C
thousand times lower than devices like the LM106 or temperature range instead of 55°C to +125°C. The
LM710. They are also designed to operate over a LM311-N has a temperature range of 0°C to +70°C.
wider range of supply voltages: from standard ±15V
op amp supplies down to the single 5V supply used
for IC logic. Their output is compatible with RTL, DTL
and TTL as well as MOS circuits. Further, they can
drive lamps or relays, switching voltages up to 50V at
currents as high as 50 mA.
Typical Applications
NOTE
Pin connections shown in Schematic Diagram and Typical Applications are for the LMC
TO-99 package.
Do Not Ground Strobe Pin. Output is turned off when current is
pulled from Strobe Pin.
Figure 1. Offset Balancing Figure 2. Strobing
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 1999–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
Increases typical common mode slew from 7.0V/μs to 18V/μs.
Figure 3. Increasing Input Stage Current Figure 4. Detector for Magnetic Transducer
*Absorbs inductive kickback of relay and protects IC from severe
voltage transients on V++ line.
Do Not Ground Strobe Pin.
Figure 5. Digital Transmission Isolator Figure 6. Relay Driver with Strobe
*Solid tantalum
Do Not Ground Strobe Pin.
Typical input current is 50 pA with inputs strobed off.
Pin connections shown in Schematic Diagram and Typical
Applications are for the LMC TO-99 package.
Figure 7. Strobing off Both Input and Output Figure 8. Positive Peak Detector
Stages
2Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
Figure 9. Zero Crossing Detector Driving MOS Logic
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
Absolute Maximum Ratings for the LM111-N/LM211-N(1)(2)
Total Supply Voltage (V84) 36V
Output to Negative Supply Voltage (V74) 50V
Ground to Negative Supply Voltage (V14) 30V
Differential Input Voltage ±30V
Input Voltage(3) ±15V
Output Short Circuit Duration 10 sec
Operating Temperature Range LM111-N 55°C to 125°C
LM211-N 25°C to 85°C
Lead Temperature (Soldering, 10 sec) 260°C
Voltage at Strobe Pin V+5V
Soldering Information Dual-In-Line Package Soldering (10 seconds) 260°C
Small Outline Package Vapor Phase (60 seconds) 215°C
Infrared (15 seconds) 220°C
ESD Rating(4) 300V
(1) Refer to RETS111X for the LM111H, LM111J and LM111J-8 military specifications.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) This rating applies for ±15 supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is
equal to the negative supply voltage or 30V below the positive supply, whichever is less.
(4) Human body model, 1.5 kΩin series with 100 pF.
Electrical Characteristics(1) for the LM111-N and LM211-N
Parameter Conditions Min Typ Max Units
Input Offset Voltage(2) TA=25°C, RS50k 0.7 3.0 mV
Input Offset Current TA=25°C 4.0 10 nA
Input Bias Current TA=25°C 60 100 nA
Voltage Gain TA=25°C 40 200 V/mV
Response Time(3) TA=25°C 200 ns
Saturation Voltage VIN≤−5 mV, IOUT=50 mA 0.75 1.5 V
TA=25°C
Strobe ON Current(4) TA=25°C 2.0 5.0 mA
Output Leakage Current VIN5 mV, VOUT=35V, TA=25°C, 0.2 10 nA
ISTROBE=3 mA
Input Offset Voltage(2) RS50 k 4.0 mV
Input Offset Current(2) 20 nA
Input Bias Current 150 nA
Input Voltage Range V+=15V, V=15V, Pin 7 Pull-Up 14.5 13.8-14.7 13.0 V
May Go To 5V
Saturation Voltage V+4.5V, V=0, VIN≤−6 mV, 0.23 0.4 V
IOUT8 mA
Output Leakage Current VIN5 mV, VOUT=35V 0.1 0.5 μA
Positive Supply Current TA=25°C 5.1 6.0 mA
Negative Supply Current TA=25°C 4.1 5.0 mA
(1) These specifications apply for VS15V and Ground pin at ground, and 55°CTA+125°C, unless otherwise stated. With the LM211-N,
however, all temperature specifications are limited to 25°CTA+85°C. The offset voltage, offset current and bias current specifications
apply for any supply voltage from a single 5V supply up to ±15V supplies.
(2) The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a
1 mA load. Thus, these parameters define an error band and take into account the worst-case effects of voltage gain and RS.
(3) The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
(4) This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not
short the strobe pin to ground; it should be current driven at 3 to 5 mA.
4Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
Absolute Maximum Ratings for the LM311-N(1)(2)
Total Supply Voltage (V84) 36V
Output to Negative Supply Voltage (V74) 40V
Ground to Negative Supply Voltage (V14) 30V
Differential Input Voltage ±30V
Input Voltage(3) ±15V
Power Dissipation(4) 500 mW
ESD Rating(5) 300V
Output Short Circuit Duration 10 sec
Operating Temperature Range to 70°C
Storage Temperature Range 65°C to 150°C
Lead Temperature (soldering, 10 sec) 260°C
Voltage at Strobe Pin V+5V
Soldering Information Dual-In-Line Package Soldering (10 seconds) 260°C
Small Outline Package Vapor Phase (60 seconds) 215°C
Infrared (15 seconds) 220°C
(1) “Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits.”
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) This rating applies for ±15V supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit
is equal to the negative supply voltage or 30V below the positive supply, whichever is less.
(4) The maximum junction temperature of the LM311-N is 110°C. For operating at elevated temperature, devices in the LMC package must
be derated based on a thermal resistance of 165°C/W, junction to ambient, or 20°C/W, junction to case. The thermal resistance of the
dual-in-line package is 100°C/W, junction to ambient.
(5) Human body model, 1.5 kΩin series with 100 pF.
Electrical Characteristics (1) for the LM311-N
Parameter Conditions Min Typ Max Units
Input Offset Voltage(2) TA=25°C, RS50k 2.0 7.5 mV
Input Offset Current(2) TA=25°C 6.0 50 nA
Input Bias Current TA=25°C 100 250 nA
Voltage Gain TA=25°C 40 200 V/mV
Response Time(3) TA=25°C 200 ns
Saturation Voltage VIN≤−10 mV, IOUT=50 mA , 0.75 1.5 V
TA=25°C
Strobe ON Current(4) TA=25°C 2.0 5.0 mA
Output Leakage Current VIN10 mV, VOUT=35V TA=25°C, 0.2 50 nA
ISTROBE=3 mA V= Pin 1 = 5V
Input Offset Voltage(2) RS50K 10 mV
Input Offset Current(2) 70 nA
Input Bias Current 300 nA
Input Voltage Range 14.5 13.8,14.7 13.0 V
Saturation Voltage V+4.5V, V=0, VIN≤−10 mV, 0.23 0.4 V
IOUT8 mA
Positive Supply Current TA=25°C 5.1 7.5 mA
Negative Supply Current TA=25°C 4.1 5.0 mA
(1) These specifications apply for VS15V and Pin 1 at ground, and 0°C < TA< +70°C, unless otherwise specified. The offset voltage,
offset current and bias current specifications apply for any supply voltage from a single 5V supply up to ±15V supplies.
(2) The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with
1 mA load. Thus, these parameters define an error band and take into account the worst-case effects of voltage gain and RS.
(3) The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
(4) This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not
short the strobe pin to ground; it should be current driven at 3 to 5 mA.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics LM111-N/LM211-N
Input Bias Current Input Bias Current
Figure 10. Figure 11.
Input Bias Current Input Bias Current
Figure 12. Figure 13.
Input Bias Current Input Bias Current
Figure 14. Figure 15.
6Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
Typical Performance Characteristics LM111-N/LM211-N (continued)
Input Bias Current Input Bias Current
Input Overdrives Input Overdrives
Figure 16. Figure 17.
Response Time for Various
Input Bias Current Input Overdrives
Figure 18. Figure 19.
Response Time for Various
Input Overdrives Output Limiting Characteristics
Figure 20. Figure 21.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics LM111-N/LM211-N (continued)
Supply Current Supply Current
Figure 22. Figure 23.
Leakage Currents
Figure 24.
8Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
Typical Performance Characteristics LM311-N
Input Bias Current Input Offset Current
Figure 25. Figure 26.
Offset Error Input Characteristics
Figure 27. Figure 28.
Common Mode Limits Transfer Function
Figure 29. Figure 30.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics LM311-N (continued)
Response Time for Various Response Time for Various
Input Overdrives Input Overdrives
Figure 31. Figure 32.
Response Time for Various
Output Saturation Voltage Input Overdrives
Figure 33. Figure 34.
Response Time for Various
Input Overdrives Output Limiting Characteristics
Figure 35. Figure 36.
10 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
Typical Performance Characteristics LM311-N (continued)
Supply Current Supply Current
Figure 37. Figure 38.
Leakage Currents
Figure 39.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
APPLICATION HINTS
CIRCUIT TECHNIQUES FOR AVOIDING
OSCILLATIONS IN COMPARATOR APPLICATIONS
When a high-speed comparator such as the LM111-N is used with fast input signals and low source impedances,
the output response will normally be fast and stable, assuming that the power supplies have been bypassed (with
0.1 μF disc capacitors), and that the output signal is routed well away from the inputs (pins 2 and 3) and also
away from pins 5 and 6.
However, when the input signal is a voltage ramp or a slow sine wave, or if the signal source impedance is high
(1 kΩto 100 kΩ), the comparator may burst into oscillation near the crossing-point. This is due to the high gain
and wide bandwidth of comparators like the LM111-N. To avoid oscillation or instability in such a usage, several
precautions are recommended, as shown in Figure 40 below.
1. The trim pins (pins 5 and 6) act as unwanted auxiliary inputs. If these pins are not connected to a trim-pot,
they should be shorted together. If they are connected to a trim-pot, a 0.01 μF capacitor C1 between pins 5
and 6 will minimize the susceptibility to AC coupling. A smaller capacitor is used if pin 5 is used for positive
feedback as in Figure 40.
2. Certain sources will produce a cleaner comparator output waveform if a 100 pF to 1000 pF capacitor C2 is
connected directly across the input pins.
3. When the signal source is applied through a resistive network, RS, it is usually advantageous to choose an
RSof substantially the same value, both for DC and for dynamic (AC) considerations. Carbon, tin-oxide, and
metal-film resistors have all been used successfully in comparator input circuitry. Inductive wirewound
resistors are not suitable.
4. When comparator circuits use input resistors (eg. summing resistors), their value and placement are
particularly important. In all cases the body of the resistor should be close to the device or socket. In other
words there should be very little lead length or printed-circuit foil run between comparator and resistor to
radiate or pick up signals. The same applies to capacitors, pots, etc. For example, if RS=10 kΩ, as little as 5
inches of lead between the resistors and the input pins can result in oscillations that are very hard to damp.
Twisting these input leads tightly is the only (second best) alternative to placing resistors close to the
comparator.
5. Since feedback to almost any pin of a comparator can result in oscillation, the printed-circuit layout should be
engineered thoughtfully. Preferably there should be a groundplane under the LM111-N circuitry, for example,
one side of a double-layer circuit card. Ground foil (or, positive supply or negative supply foil) should extend
between the output and the inputs, to act as a guard. The foil connections for the inputs should be as small
and compact as possible, and should be essentially surrounded by ground foil on all sides, to guard against
capacitive coupling from any high-level signals (such as the output). If pins 5 and 6 are not used, they should
be shorted together. If they are connected to a trim-pot, the trim-pot should be located, at most, a few inches
away from the LM111-N, and the 0.01 μF capacitor should be installed. If this capacitor cannot be used, a
shielding printed-circuit foil may be advisable between pins 6 and 7. The power supply bypass capacitors
should be located within a couple inches of the LM111-N. (Some other comparators require the power-supply
bypass to be located immediately adjacent to the comparator.)
6. It is a standard procedure to use hysteresis (positive feedback) around a comparator, to prevent oscillation,
and to avoid excessive noise on the output because the comparator is a good amplifier for its own noise. In
the circuit of Figure 41, the feedback from the output to the positive input will cause about 3 mV of
hysteresis. However, if RSis larger than 100Ω, such as 50 kΩ, it would not be reasonable to simply increase
the value of the positive feedback resistor above 510 kΩ. The circuit of Figure 42 could be used, but it is
rather awkward. See the notes in paragraph 7 below.
7. When both inputs of the LM111-N are connected to active signals, or if a high-impedance signal is driving the
positive input of the LM111-N so that positive feedback would be disruptive, the circuit of Figure 40 is ideal.
The positive feedback is to pin 5 (one of the offset adjustment pins). It is sufficient to cause 1 to 2 mV
hysteresis and sharp transitions with input triangle waves from a few Hz to hundreds of kHz. The positive-
feedback signal across the 82Ωresistor swings 240 mV below the positive supply. This signal is centered
around the nominal voltage at pin 5, so this feedback does not add to the VOS of the comparator. As much as
8 mV of VOS can be trimmed out, using the 5 kΩpot and 3 kΩresistor as shown.
8. These application notes apply specifically to the LM111-N, LM211-N, LM311-N, and LF111 families of
comparators, and are applicable to all high-speed comparators in general, (with the exception that not all
comparators have trim pins).
12 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
Pin connections shown are for LM111H in the LMC hermetic package.
Figure 40. Improved Positive Feedback
Pin connections shown are for LM111H in the LMC hermetic package.
Figure 41. Conventional Positive Feedback
Figure 42. Positive Feedback with High Source Resistance
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
Typical Applications
(Pin numbers refer to LMC package)
Figure 43. Zero Crossing Detector Driving MOS Switch
*TTL or DTL fanout of two
Figure 44. 100 kHz Free Running Multivibrator
*Adjust for symmetrical square wave time when VIN = 5 mV
†Minimum capacitance 20 pF Maximum frequency 50 kHz
Figure 45. 10 Hz to 10 kHz Voltage Controlled Oscillator
14 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
*Input polarity is reversed when using pin 1 as output.
Figure 46. Driving Ground-Referred Load
Figure 47. Using Clamp Diodes to Improve Response
*Values shown are for a 0 to 30V logic swing and a 15V threshold.
†May be added to control speed and reduce susceptibility to noise spikes.
Figure 48. TTL Interface with High Level Logic
Figure 49. Crystal Oscillator
Figure 50. Comparator and Solenoid Driver
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
*Solid tantalum
†Adjust to set clamp level
Figure 51. Precision Squarer
*Solid tantalum
Figure 52. Low-Voltage Adjustable Reference Supply
*Solid tantalum
Figure 53. Positive Peak Detector
16 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
Figure 54. Zero Crossing Detector Driving MOS Logic
*Solid tantalum
Figure 55. Negative Peak Detector
*R2 sets the comparison level. At comparison, the photodiode has less than 5 mV across it, decreasing leakages by
an order of magnitude.
Figure 56. Precision Photodiode Comparator
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
Figure 57. Switching Power Amplifier
Figure 58. Switching Power Amplifier
18 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
Schematic Diagram
NOTE
Pin connections shown in the schematic diagram are for the LMC package.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
SNOSBJ1E MAY 1999REVISED MARCH 2013
www.ti.com
Pin Diagrams
Top View
Figure 59. 8-Pin TO-99
See LMC Package
Top View Top View
Figure 60. 8-Pin CDIP (See NAB Package) Figure 61. 14-Pin CDIP (See J Package)
8-Pin SOIC (See D Package) 14-Pin PDIP (See NFF Package)
8-Pin PDIP (See P Package)
Top View
Figure 62. LM111W/883, LM111WG/883
10-Pin CLGA (See NAD Package)
10-Pin CLGA (See NAC Package)
20 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM111-N LM211-N LM311-N
LM111-N, LM211-N, LM311-N
www.ti.com
SNOSBJ1E MAY 1999REVISED MARCH 2013
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 20
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM111-N LM211-N LM311-N
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM111H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI -55 to 125 LM111H
LM111H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) POST-PLATE Level-1-NA-UNLIM -55 to 125 LM111H
LM111J-8 ACTIVE CDIP NAB 8 40 TBD Call TI Call TI -55 to 125 LM111J-8
LM311H ACTIVE TO-99 LMC 8 500 TBD Call TI Call TI 0 to 70 LM311H
LM311H/NOPB ACTIVE TO-99 LMC 8 500 Green (RoHS
& no Sb/Br) POST-PLATE Level-1-NA-UNLIM 0 to 70 LM311H
LM311M NRND SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM
311M
LM311M/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM
311M
LM311MX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 70 LM
311M
LM311MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM
311M
LM311N NRND PDIP P 8 40 TBD Call TI Call TI 0 to 70 LM
311N
LM311N/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-NA-UNLIM 0 to 70 LM
311N
MLM311P NRND PDIP P 8 40 TBD Call TI Call TI 0 to 70 LM
311N
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 2
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM311MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM311MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Sep-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM311MX SOIC D 8 2500 367.0 367.0 35.0
LM311MX/NOPB SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Sep-2013
Pack Materials-Page 2
MECHANICAL DATA
NAB0008A
www.ti.com
J08A (Rev M)
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated