MAX4172 Low-Cost, Precision, High-Side Current-Sense Amplifier General Description The MAX4172 is a low-cost, precision, high-side currentsense amplifier for portable PCs, telephones, and other systems where battery/DC power-line monitoring is critical. High-side power-line monitoring is especially useful in battery-powered systems, since it does not interfere with the battery charger's ground path. Wide bandwidth and ground-sensing capability make the device suitable for closed-loop battery-charger and general-purpose currentsource applications. The 0 to 32V input common-mode range is independent of the supply voltage, which ensures that current-sense feedback remains viable, even when connected to a battery in deep discharge. Benefits and Features Ideal for High-Side Monitoring * 3V to 32V Supply Operation * 0.5% Typical Full-Scale Accuracy Over Temperature * High Accuracy +2V to +32V Common-Mode Range, Functional Down to 0V, Independent of Supply Voltage * 800kHz Bandwidth [VSENSE = 100mV (1C)] * 200kHz Bandwidth [VSENSE = 6.25mV (C/16)] Minimizes Board Space Requirements * MAX and SO Packages To provide a high level of flexibility, the MAX4172 functions with an external sense resistor to set the range of load current to be monitored. It has a current output that can be converted to a ground-referred voltage with a single resistor, accommodating a wide range of battery voltages and currents. Ordering Information An open-collector power-good output (PG) indicates when the supply voltage reaches an adequate level to guarantee proper operation of the current-sense amplifier. The MAX4172 operates with a 3.0V to 32V supply voltage, and is available in a space-saving, 8-pin MAX(R) or SO package. +Denotes a lead(Pb)-free/RoHS-compliant package. Applications Portable PCs: Notebooks/Subnotebooks/Palmtops Battery-Powered/Portable Equipment Closed-Loop Battery Chargers/Current Sources Smart-Battery Packs Portable/Cellular Phones Portable Test/Measurement Systems Energy Management Systems TEMP RANGE PIN-PACKAGE MAX4172ESA+ PART -40C to +85C 8 SO MAX4172EUA+ -40C to +85C 8 MAX MAX4172GUA+ -40C to +105C 8 MAX Typical Operating Circuit UNREGULATED DC SUPPLY 3V TO 32V RSENSE 50m LOW-COST SWITCHING REGULATOR VSENSE RS+ GND + 8 V+ 7 PG N.C. 3 6 OUT N.C. 4 5 GND RS- 2 MAX4172 100k PG MAX4172 OUT TOP VIEW POWER GOOD MAX is a registered trademark of Maxim Integrated Products, Inc. 19-1184; Rev 4; 6/16 LOAD/ BATTERY IOUT = VSENSE / 100 FEEDBACK LOOP VOUT = 500mV/A ROUT 1k LOW-COST BATTERY CHARGER/CURRENT SOURCE MAX/SO 2A ANALOG OR LOGIC SUPPLY RS- V+ Pin Configuration RS+ 1 0 TO 32V MAX4172 Low-Cost, Precision, High-Side Current-Sense Amplifier Absolute Maximum Ratings V+, RS+, RS-, PG..................................................-0.3V to +36V OUT..............................................................-0.3V to (V+ + 0.3V) Differential Input Voltage, VRS+ - VRS-...........................700mV Current into Any Pin..........................................................50mA Continuous Power Dissipation (TA = +70C) SO (derate 5.88mW/C above +70C).........................471mW MAX (derate 4.10mW/C above +70C)....................330mW Operating Temperature Range MAX4172E_A.................................................. -40C to +85C MAX4172G_A................................................ -40C to +105C Storage Temperature Range............................. -65C to +150C Lead Temperature (soldering, 10s).................................. +300C Soldering Temperature (reflow)........................................+260C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (V+ = +3V to +32V; VRS+, VRS- = 0 to 32V; TA = TMIN to TMAX; unless otherwise noted. Typical values are at V+ = +12V, VRS+ = 12V, TA = +25C.) PARAMETER Operating Voltage Range Input Voltage Range Supply Current Input Offset Voltage SYMBOL VRS- 0 IV+ VOS IRS+ Negative Input Bias Current IRS- Maximum VSENSE Voltage V+ = 12V, VRS+ = 12V IOUT/V+ UNITS 32 V V 0.8 1.6 mA MAX4172ESA 0.1 0.75 MAX4172EUA 0.2 1.6 mV 4 0 VRS+ 2.0V, IOUT = 0mA -325 VRS+ 2.0V -650 VRS+ > 2.0V IOUT/VRS+ 2.0V < VRS+ < 32V MAX 32 VRS+ > 2.0V, IOUT = 0mA 3V V+ 32V, VRS+ > 2.0V TYP 0 VRS+ 2.0V VSENSE = 100mV, V+ = 12V, VRS+ = 12V Output Current Error www.maximintegrated.com IOUT = 0mA VSENSE = 6.25mV, V+ = 12V, VRS+ = 12V (Note 1) Low-Level Current Error OUT Common-Mode Rejection Ratio MIN 3 Positive Input Bias Current OUT Power-Supply Rejection Ratio CONDITIONS V+ 0 150 27 42.5 +42.5 50 85 85 175 A A mV MAX4172ESA 8.0 MAX4172EUA 15 MAX4172ESA, TA = -40C to 0C 20 MAX4172EUA, TA = -40C to 0C 50 MAX4172ESA, TA = 0C to +105C 10 MAX4172EUA, TA = 0C to +105C 15 A A 0.2 A/V 0.03 A/V Maxim Integrated 2 MAX4172 Low-Cost, Precision, High-Side Current-Sense Amplifier Electrical Characteristics (continued) (V+ = +3V to +32V; VRS+, VRS- = 0 to 32V; TA = TMIN to TMAX; unless otherwise noted. Typical values are at V+ = +12V, VRS+ = 12V, TA = +25C.) PARAMETER SYMBOL CONDITIONS Maximum Output Voltage (OUT) MIN TYP IOUT 1.5mA VSENSE = 100mV Bandwidth Maximum Output Current Transconductance V+ Threshold for PG Output Low (Note 2) PG Output Low Voltage VOL Leakage Current into PG V+ - 1.2 V kHz 200 TA = 0C to +105C Gm = IOUT/(VRS+ - VRS-), VSENSE = 100mV, VRS+ > 2.0V TA = -40C to 0C Gm UNITS 800 VSENSE = 6.25mV (Note 1) IOUT MAX 1.5 1.75 9.8 10 10.2 9.7 10 10.3 V+ rising 2.77 V+ falling 2.67 mA mA/V V ISINK = 1.2mA, V+ = 2.9V, TA = +25C 0.4 V 1 A 1 A V+ = 2.5V, TA = +25C Power-Off Input Leakage Current (RS+, RS-) V+ = 0V, VRS+ = VRS- = 32V 0.1 OUT Rise Time VSENSE = 0 to 100mV, 10% to 90% 400 ns 800 ns OUT Fall Time VSENSE = 100mV to 0mV, 90% to 10% OUT Settling Time to 1% VSENSE = 5mV to 100mV OUT Output Resistance VSENSE = 150mV Rising 1.3 Falling 6 s 20 M Note 1: 6.25mV = 1/16 of typical full-scale sense voltage (C/16). Note 2: Valid operation of the MAX4172 is guaranteed by design when PG is low. Typical Operating Characteristics (V+ = +12V, VRS+ = 12V, ROUT = 1k, TA = +25C, unless otherwise noted.) TA = -40C 0.8 750 TA = +25C 650 0 10 20 V+ (V) www.maximintegrated.com 30 0.6 0.5 0.4 TA = +85C 40 0 0 10 2 0 TA = +85C -4 TA = +25C 0.1 20 V+ (V) 30 TA = -40C TA = +25C -2 0.2 IOUT = 0mA VSENSE = 6.25mV 6 4 TA = +105C 0.3 TA = -40C 550 8 0.7 TA = +85C 850 VSENSE = 100mV 40 MAX4172-03 0.9 ERROR (%) 950 450 1.0 MAX4172-01 TA = +105C ERROR (%) QUIESCENT SUPPLY CURRENT (A) 1050 C/16 LOAD OUTPUT ERROR vs. SUPPLY VOLTAGE OUTPUT ERROR vs. SUPPLY VOLTAGE MAX4172-02 SUPPLY CURRENT vs. SUPPLY VOLTAGE -6 TA = +105C 0 10 20 IOUT = 0mA 30 40 V+ (V) Maxim Integrated 3 MAX4172 Low-Cost, Precision, High-Side Current-Sense Amplifier Typical Operating Characteristics (continued) (V+ = +12V, VRS+ = 12V, ROUT = 1k, TA = +25C, unless otherwise noted.) 35 MAX4172-04 40 35 ERROR (%) 20 15 20 15 10 5mVP-P 5 0 0.1m 10m 1m 100m 0.1 1 10 100 1000 POWER-SUPPLY FREQUENCY (kHz) OUTPUT ERROR vs. COMMON MODE VOLTAGE V+ THRESHOLD FOR PG OUTPUT LOW vs. TEMPERATURE VSENSE = 100mV TA = -40C TA = +105C 2.98 2.88 V+ TRIP THRESHOLD (V) 0.6 -0.2 0.01 VSENSE (V) TA = +85C 0.2 0 1 MAX4172-06 1.0 OUTPUT ERROR (%) 1.0VP-P 10 5 TA = +25C -0.6 -1.0 2.78 2.68 2.58 2.48 -1.4 -1.8 0.5VP-P MAX4172-07 ERROR (%) 25 25 -5 VSENSE = 100mV 30 30 MAX4172-05 POWER-SUPPLY REJECTION RATIO vs. FREQUENCY ERROR vs. SENSE VOLTAGE 0 4 8 12 16 20 24 28 2.38 32 -50 -25 0 25 50 75 100 125 TEMPERATURE (C) V+ (V) 0 to 100mV VSENSE TRANSIENT RESPONSE 0 to 10mV VSENSE TRANSIENT RESPONSE MAX4172-09 MAX4172-08 VSENSE 50mV/div VSENSE 5mV/div GND GND VOUT 500mV/div VOUT 50mV/div GND GND 10s/div www.maximintegrated.com 10s/div Maxim Integrated 4 MAX4172 Low-Cost, Precision, High-Side Current-Sense Amplifier Typical Operating Characteristics (continued) (V+ = +12V, VRS+ = 12V, ROUT = 1k, TA = +25C, unless otherwise noted.) STARTUP DELAY V+ to PG POWER-UP DELAY MAX4172-10 VOUT 500mV/div MAX4172-11 PG 2V/div GND GND V+ 2V/div V+ 2V/div GND GND 5s/div VSENSE = 100mV 10ms/div 100kW PULLUP RESISTOR FROM PG TO +4V Pin Description PIN NAME 1 RS+ Power connection to the external sense resistor. The "+" indicates the direction of current flow. FUNCTION 2 RS- Load-side connection for the external sense resistor. The "-" indicates the direction of current flow. 3, 4 N.C. No Connect. No internal connection. Leave open or connect to GND. 5 GND Ground 6 OUT Current Output. OUT is proportional to the magnitude of the sense voltage (VRS+ - VRS-). A 1k resistor from OUT to ground will result in a voltage equal to 10V/V of sense voltage. 7 PG Power Good Open-Collector Logic Output. A low level indicates that V+ is sufficient to power the MAX4172, and adequate time has passed for power-on transients to settle out. 8 V+ Supply Voltage Input for the MAX4172 Detailed Description The MAX4172 is a unidirectional, high-side currentsense amplifier with an input common-mode range that is independent of supply voltage. This feature not only allows the monitoring of current flow into a battery in deep discharge, but also enables high-side current sensing at voltages far in excess of the supply voltage (V+). The MAX4172 current-sense amplifier's unique topology simplifies current monitoring and control. The MAX4172's amplifier operates as shown in Figure 1. The battery/ load current flows through the external sense resistor www.maximintegrated.com (RSENSE), from the RS+ node to the RSnode. Current flows through RG1 and Q1, and into the current mirror, where it is multiplied by a factor of 50 before appearing at OUT. To analyze the circuit of Figure 1, assume that current flows from RS+ to RS-, and that OUT is connected to GND through a resistor. Since A1's inverting input is high impedance, no current flows though RG2 (neglecting the input bias current), so A1's negative input is equal to VSOURCE - (ILOAD x RSENSE). A1's open-loop gain forces its positive input to essentially the same voltage level as the negative input. Therefore, the drop across RG1 equals Maxim Integrated 5 MAX4172 ILOAD x RSENSE. Then, since IRG1 flows through RG1, IRG1 x RG1 = ILOAD x RSENSE. The internal current mirror multiplies IRG1 by a factor of 50 to give IOUT = 50 x IRG1. Substituting IOUT/50 for IRG1, (IOUT/50) x RG1 = ILOAD x RSENSE, or: Low-Cost, Precision, High-Side Current-Sense Amplifier RS+ OUT is a high-impedance current source that can be integrated by connecting it to a capacitive load. PG Output The PG output is an open-collector logic output that indicates the status of the MAX4172's V+ power supply. A logic low on the PG output indicates that V+ is sufficient to power the MAX4172. This level is temperature dependent (see Typical Operating Characteristics graphs), and is typically 2.7V at room temperature. The internal PG comparator has a 100mV (typ) hysteresis to prevent possible oscillations caused by repeated toggling of the PG output, making the device ideal for power-management systems lacking soft-start capability. An internal delay (15s, typ) in the PG comparator allows adequate time for power-on transients to settle out. The PG status indicator greatly simplifies the design of closed-loop www.maximintegrated.com A1 MAX4172 Q1 V+ 1:50 CURRENT MIRROR The output voltage equation for the MAX4172 is given below: ROUT = (VOUT)/(ILOAD x RSENSE x Gm) RSRG2 IRG1 Current Output The full-scale output voltage range can be set by changing the ROUT resistor value, but the output voltage must be no greater than V+ - 1.2V. The above equation can be modified to determine the ROUT required for a particular full-scale range: VSENSE RG1 IOUT = Gm x (VRS+ - VRS-) = (10mA/V) x (ILOAD x RSENSE) where VOUT = the desired full-scale output voltage, ILOAD equals the full-scale current being sensed, RSENSE equals the current-sense resistor, ROUT equals the voltage-setting resistor, and Gm equals the device's transconductance (10mA/V). TO LOAD/ BATTERY INPUT IOUT = 50 x ILOAD x (RSENSE/RG1) The internal current gain of 50 and the factory-trimmed resistor RG1 combine to result in the device's transconductance (Gm) of 10mA/V. Gm is defined as being equal to IOUT/(VRS+ - VRS-). Since (VRS+ - VRS-) = ILOAD x RSENSE, the output current (IOUT) can be calculated with the following formula: VOUT = (Gm) x (RSENSE x ROUT x ILOAD) ILOAD RSENSE IOUT = 50 IRG1 OUT V+ PG VTH GND Figure 1. Functional Diagram systems by ensuring that the components in the control loop have sufficient voltage to operate correctly. Applications Information Suggested Component Values for Various Applications The Typical Operating Circuit is useful in a wide variety of applications. Table 1 shows suggested component values and indicates the resulting scale factors for various applications required to sense currents from 100mA to 10A. Adjust the RSENSE value to monitor higher/lower current levels. Select RSENSE using the guidelines and formulas in the following section. Maxim Integrated 6 MAX4172 Low-Cost, Precision, High-Side Current-Sense Amplifier Table 1. Suggested Component Values FULL-SCALE LOAD CURRENT (A) CURRENT-SENSE RESISTOR, RSENSE (m) OUTPUT RESISTOR, ROUT (k) FULL-SCALE OUTPUT VOLTAGE, VOUT (V) SCALE FACTOR, VOUT/ISENSE (V/A) 0.1 1000 3.48 3.48 34.8 1 100 3.48 3.48 3.48 5 20 3.48 3.48 0.696 10 10 3.48 3.48 .348 Sense Resistor, RSENSE Choose RSENSE based on the following criteria: Voltage Loss: A high RSENSE value causes the power-source voltage to degrade through IR loss. For minimal voltage loss, use the lowest RSENSE value. Accuracy: A high RSENSE value allows lower currents to be measured more accurately. This is because offsets become less significant when the sense voltage is larger. For best performance, select RSENSE to provide approximately 100mV of sense voltage for the full-scale current in each application. Efficiency and Power Dissipation: At high current levels, the I2R losses in RSENSE can be significant. Take this into consideration when choosing the resistor value and its power dissipation (wattage) rating. Also, the sense resistor's value might drift if it is allowed to heat up excessively. Inductance: Keep inductance low if ISENSE has a large high-frequency component. Wire-wound resistors have the highest inductance, while metal film is somewhat better. Low-inductance metal-film resistors are also available. Instead of being spiral wrapped around a core, as in metal-film or wirewound resistors, they are a straight band of metal and are available in values under 1. Cost: If the cost of RSENSE is an issue, you might want to use an alternative solution, as shown in Figure 2. This solution uses the PCB traces to create a sense resistor. Because of the inaccuracies of the copper resistor, the full-scale current value must be adjusted with a potentiometer. Also, copper's resistance temperature coefficient is fairly high (approximately 0.4%/C). In Figure 2, assume that the load current to be measured is 10A, and that you have determined a 0.3-inchwide, 2-ounce copper to be appropriate. The resistivity of 0.1-inch-wide, 2-ounce (70m thickness) copper is 30m/ ft. For 10A, you might want RSENSE = 5m for a 50mV drop at full scale. This resistor requires about 2 inches of 0.1-inch-wide copper trace. www.maximintegrated.com INPUT LOAD/BATTERY RSENSE O.3 in. COPPER O.3 in. COPPER O.1 in. COPPER VSENSE 1 2 RS+ MAX4172 V+ VSUPPLY 3V TO 32V 8 RS- OUT GND 6 5 ROUT Figure 2. MAX4172 Connections Showing Use of PC Board Current-Sense Adjustment (Resistor Range, Output Adjust) Choose ROUT after selecting RSENSE. Choose ROUT to obtain the full-scale voltage you require, given the full-scale IOUT determined by RSENSE. OUT's high impedance permits using ROUT values up to 200k with minimal error. OUT's load impedance (e.g., the input of an op amp or ADC) must be much greater than ROUT (e.g., 100 x ROUT) to avoid degrading measurement accuracy. High-Current Measurement The MAX4172 can achieve high-current measurements by using low-value sense resistors, which can be paralleled to further increase the current-sense limit. As an alternative, PCB traces can be adjusted over a wide range. Maxim Integrated 7 MAX4172 Low-Cost, Precision, High-Side Current-Sense Amplifier Power-Supply Bypassing and Grounding In most applications, grounding the MAX4172 requires no special precautions. However, in high-current systems, large voltage drops can develop across the ground plane, which can add to or subtract from VOUT. Use a single-point star ground for the highest currentmeasurement accuracy. Chip Information SUBSTRATE CONNECTED TO GND The MAX4172 requires no special bypassing and responds quickly to transient changes in line current. If the noise at OUT caused by these transients is a problem, you can place a 1F capacitor at the OUT pin to ground. You can also place a large capacitor at the RS terminal (or load side of the MAX4172) to decouple the load, reducing the current transients. These capacitors are not required for MAX4172 operation or stability. The RS+ and RSinputs can be filtered by placing a capacitor (e.g., 1F) between them to average the sensed current. Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. SO S8+4 21-0041 90-0096 MAX U8+1 21-0036 90-0092 www.maximintegrated.com Maxim Integrated 8 MAX4172 Low-Cost, Precision, High-Side Current-Sense Amplifier Revision History REVISION NUMBER REVISION DATE PAGES CHANGED 0 12/96 Initial release 1 6/10 Clarified 0 to 2V is not a high-accuracy range for the device, removed future product reference, added lead-free options and soldering temperature 2 10/12 Revised the Package Information 8 3 5/15 Revised Benefits and Features section 1 4 6/16 Added G-temp grade for 105C operation and updated Typical Operating Characteristics section DESCRIPTION -- 1, 2 1-4 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2016 Maxim Integrated Products, Inc. 9