MOTOROLA Order this document by MCM6726D/D SEMICONDUCTOR TECHNICAL DATA 128K x 8 Bit Fast Static Random Access Memory The MCM6726D is a 1,048,576 bit static random access memory organized as 131,072 words of 8 bits. Static design eliminates the need for external clocks or timing strobes. Output enable (G) is a special control feature that provides increased system flexibility and eliminates bus contention problems. This device meets JEDEC standards for functionality and revolutionary pinout, and is available in a 400 mil plastic small-outline J-leaded package. * * * * * * Single 5 V 10% Power Supply Fully Static -- No Clock or Timing Strobes Necessary All Inputs and Outputs Are TTL Compatible Three State Outputs Fast Access Times: 8, 10, 12 ns Center Power and I/O Pins for Reduced Noise BLOCK DIAGRAM A VCC VSS A A A A MEMORY MATRIX 512 ROWS x 256 x 8 COLUMNS ROW DECODER A MCM6726D WJ PACKAGE 400 MIL SOJ CASE 857A-02 PIN ASSIGNMENT A 1 32 A A 2 31 A A 3 30 A A 4 29 A E 5 28 G DQ 6 27 DQ DQ 7 26 DQ VCC 8 25 VSS VSS 9 24 VCC DQ 10 23 DQ DQ 11 22 DQ W 12 21 A A 13 20 A A 14 19 A A A 15 18 A A A 16 17 A A DQ COLUMN I/O COLUMN DECODER INPUT DATA CONTROL DQ E A A A A A A PIN NAMES A A A . . . . . . . . . . . . . . . . . . . . Address Input E . . . . . . . . . . . . . . . . . . . . . . Chip Enable W . . . . . . . . . . . . . . . . . . . . Write Enable G . . . . . . . . . . . . . . . . . . . Output Enable DQ . . . . . . . . . . . . . . . Data Input/Output VCC . . . . . . . . . . . . + 5 V Power Supply VSS . . . . . . . . . . . . . . . . . . . . . . . Ground W G 10/9/96 Motorola, Inc. 1996 MOTOROLA FAST SRAM MCM6726D 1 TRUTH TABLE (X = Don't Care) E G W Mode VCC Current Output Cycle H X X Not Selected ISB1, ISB2 High-Z -- L H H Output Disabled ICCA High-Z -- L L H Read ICCA Dout Read Cycle L X L Write ICCA High-Z Write Cycle ABSOLUTE MAXIMUM RATINGS (See Note) Symbol Value Unit VCC - 0.5 to + 7.0 V Vin, Vout - 0.5 to VCC + 0.5 V Output Current Iout 30 mA Power Dissipation PD 1.2 W Temperature Under Bias Tbias - 10 to + 85 C Operating Temperature TA 0 to + 70 C Tstg - 55 to + 125 C Rating Power Supply Voltage Voltage Relative to VSS for Any Pin Except VCC Storage Temperature -- Plastic This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to these high-impedance circuits. This BiCMOS memory circuit has been designed to meet the dc and ac specifications shown in the tables, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow of at least 500 linear feet per minute is maintained. NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to RECOMMENDED OPERATING CONDITIONS. Exposure to higher than recommended voltages for extended periods of time could affect device reliability. DC OPERATING CONDITIONS AND CHARACTERISTICS (VCC = 5.0 V 10%, TA = 0 to 70C, Unless Otherwise Noted) RECOMMENDED OPERATING CONDITIONS Symbol Min Typ Max Unit Supply Voltage (Operating Voltage Range) Parameter VCC 4.5 5.0 5.5 V Input High Voltage VIH 2.2 -- VCC + 0.3** V Input Low Voltage VIL - 0.5* -- 0.8 V Symbol Min Max Unit Input Leakage Current (All Inputs, Vin = 0 to VCC) Ilkg(I) -- 1.0 A Output Leakage Current (E = VIH, Vout = 0 to VCC) * VIL (min) = -0.5 V dc; VIL (min) = -2.0 V ac (pulse width 2.0 ns) for I 20.0 mA. ** VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2 V ac (pulse width 2.0 ns) for I 20.0 mA. DC CHARACTERISTICS Parameter Ilkg(O) -- 1.0 A Output Low Voltage (IOL = + 8.0 mA) VOL -- 0.4 V Output High Voltage (IOH = - 4.0 mA) VOH 2.4 -- V POWER SUPPLY CURRENTS Parameter Symbol 6726D-8 6726D-10 6726D-12 Unit Notes AC Active Supply Current (Iout = 0 mA) (VCC = max, f = fmax) ICCA 195 175 165 mA 1, 2, 3 Active Quiescent Current (E = VIL, VCC = max, f = 0 MHz) ICC2 100 100 100 mA AC Standby Current (E = VIH, VCC = max, f = fmax) ISB1 60 60 60 mA CMOS Standby Current (VCC = max, f = 0 MHz, E VCC - 0.2 V, Vin VSS + 0.2 V, or VCC - 0.2 V) ISB2 20 20 20 mA 1, 2, 3 NOTES: 1. Reference AC Operating Conditions and Characteristics for input and timing (VIH/VIL, tr/tf, pulse level 0 to 3.0 V, VIH = 3.0 V). 2. All addresses transition simultaneously low (LSB) and then high (MSB). 3. Data states are all zero. MCM6726D 2 MOTOROLA FAST SRAM CAPACITANCE (f = 1.0 MHz, dV = 3.0 V, TA = 25C, Periodically Sampled Rather Than 100% Tested) Symbol Typ Max Unit Address Input Capacitance Cin -- 6 pF Control Pin Input Capacitance Cin -- 6 pF Input/Output Capacitance CI/O -- 8 pF Parameter AC OPERATING CONDITIONS AND CHARACTERISTICS (VCC = 5.0 V 10%, TA = 0 to +70C, Unless Otherwise Noted) Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ns Output Timing Measurement Reference Level . . . . . . . . . . . . . 1.5 V Output Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Figure 1a READ CYCLE TIMING (See Notes 1 and 2) 6726D-8 Parameter 6726D-10 6726D-12 Symbol Min Max Min Max Min Max Unit Notes Read Cycle Time tAVAV 8 -- 10 -- 12 -- ns 3 Address Access Time tAVQV -- 8 -- 10 -- 12 ns Enable Access Time tELQV -- 8 -- 10 -- 12 ns Output Enable Access Time tGLQV -- 4 -- 5 -- 6 ns Output Hold from Address Change tAXQX 3 -- 3 -- 3 -- ns Enable Low to Output Active tELQX 3 -- 3 -- 3 -- ns 4,5,6 Output Enable Low to Output Active tGLQX 0 -- 0 -- 0 -- ns 4,5,6 Enable High to Output High-Z tEHQZ -- 4 -- 5 -- 6 ns 4,5,6 Output Enable High to Output High-Z tGHQZ -- 4 -- 5 -- 6 ns 4,5,6 NOTES: 1. W is high for read cycle. 2. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycles. 3. All read cycle timings are referenced from the last valid address to the first transitioning address. 4. At any given voltage and temperature, tEHQZ max < tELQX min, and tGHQZ max < tGLQX min, both for a given device and from device to device. 5. Transition is measured 200 mV from steady-state voltage with load of Figure 1b. 6. This parameter is sampled and not 100% tested. 7. Device is continuously selected (E = VIL, G = VIL). 8. Addresses valid prior to or coincident with E going low. TIMING LIMITS +5 V 480 OUTPUT RL = 50 Z0 = 50 OUTPUT 255 5 pF VL = 1.5 V (a) The table of timing values shows either a minimum or a maximum limit for each parameter. Input requirements are specified from the external system point of view. Thus, address setup time is shown as a minimum since the system must supply at least that much time. On the other hand, responses from the memory are specified from the device point of view. Thus, the access time is shown as a maximum since the device never provides data later than that time. (b) Figure 1. AC TEST LOADS MOTOROLA FAST SRAM MCM6726D 3 READ CYCLE 1 (See Note 7) tAVAV A (ADDRESS) tAXQX Q (DATA OUT) PREVIOUS DATA VALID DATA VALID tAVQV READ CYCLE 2 (See Note 8) tAVAV A (ADDRESS) tAVQV tELQV E (CHIP ENABLE) tEHQZ tELQX G (OUTPUT ENABLE) tGHQZ tGLQV tGLQX Q (DATA OUT) MCM6726D 4 DATA VALID MOTOROLA FAST SRAM WRITE CYCLE 1 (W Controlled, See Notes 1 and 2) 6726D-8 Parameter 6726D-10 6726D-12 Symbol Min Max Min Max Min Max Unit Notes tAVAV 8 -- 10 -- 12 -- ns 3 Address Setup Time tAVWL 0 -- 0 -- 0 -- ns Address Valid to End of Write tAVWH 8 -- 9 -- 10 -- ns Address Valid to End of Write, G High tAVWH 7 -- 8 -- 9 -- ns Write Pulse Width tWLWH, tWLEH 8 -- 9 -- 10 -- ns Write Pulse Width, G High tWLWH, tWLEH 7 -- 8 -- 9 -- ns Data Valid to End of Write tDVWH 4 -- 5 -- 6 -- ns Data Hold Time tWHDX 0 -- 0 -- 0 -- ns Write Low to Data High-Z tWLQZ -- 4 -- 5 -- 6 ns 4,5,6 Write High to Output Active tWHQX 3 -- 3 -- 3 -- ns 4,5,6 Write Recovery Time tWHAX 0 -- 0 -- 0 -- ns Write Cycle Time NOTES: 1. A write occurs during the overlap of E low and W low. 2. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycles. 3. All write cycle timings are referenced from the last valid address to the first transitioning address. 4. Transition is measured 200 mV from steady-state voltage with load of Figure 1b. 5. This parameter is sampled and not 100% tested. 6. At any given voltage and temperature, tWLQZ max < tWHQX min both for a given device and from device to device. WRITE CYCLE 1 tAVAV A (ADDRESS) tAVWH tWHAX E (CHIP ENABLE) tWLEH tWLWH W (WRITE ENABLE) tDVWH tAVWL D (DATA IN) tWHDX DATA VALID tWLQZ Q (DATA OUT) HIGH-Z HIGH-Z tWHQX MOTOROLA FAST SRAM MCM6726D 5 WRITE CYCLE 2 (E Controlled, See Notes 1 and 2) 6726D-8 Parameter 6726D-10 6726D-12 Symbol Min Max Min Max Min Max Unit Notes tAVAV 8 -- 10 -- 12 -- ns 3 Address Setup Time tAVEL 0 -- 0 -- 0 -- ns Address Valid to End of Write tAVEH 7 -- 8 -- 9 -- ns Enable to End of Write tELEH, tELWH 7 -- 8 -- 9 -- ns Data Valid to End of Write tDVEH 4 -- 5 -- 6 -- ns Data Hold Time tEHDX 0 -- 0 -- 0 -- ns Write Recovery Time tEHAX 0 -- 0 -- 0 -- ns Write Cycle Time 4,5 NOTES: 1. A write occurs during the overlap of E low and W low. 2. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycles. 3. All write cycle timings are referenced from the last valid address to the first transitioning address. 4. If E goes low coincident with or after W goes low, the output will remain in a high impedance condition. 5. If E goes high coincident with or before W goes high, the output will remain in a high impedance condition. WRITE CYCLE 2 tAVAV A (ADDRESS) tAVEH tELEH E (CHIP ENABLE) tAVEL tELWH tEHAX W (WRITE ENABLE) tDVEH D (DATA IN) tEHDX DATA VALID HIGH-Z Q (DATA OUT) ORDERING INFORMATION (Order by Full Part Number) MCM 6726D WJ XX X Motorola Memory Prefix Shipping Method (R = Tape and Reel, Blank = Rails) Part Number Speed (8 = 8 ns, 10 = 10 ns, 12 = 12 ns) Package (WJ = 400 mil SOJ) Full Part Numbers -- MCM6726DWJ8 MCM6726DWJ8R MCM6726D 6 MCM6726DWJ10 MCM6726DWJ10R MCM6726DWJ12 MCM6726DWJ12R MOTOROLA FAST SRAM PACKAGE DIMENSIONS 32-LEAD 400 MIL SOJ CASE 857A-02 F 32 PL 0.17 (0.007) T B S S A S N 32 D 32 PL 0.17 (0.007) S 17 1 T B A S S NOTE 3 DETAIL Z 16 0.17 (0.007) -A- S T A S B S P L G -BE C 0.10 (0.004) K DETAIL Z -T- SEATING PLANE S RADIUS R 0.25 (0.010) S T A S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TO BE DETERMINED AT PLANE -T-. 4. DIMENSION A & B DO NOT INCLUDE MOLD PROTRUSION. MOLD PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 5. DIMENSION A & B INCLUDE MOLD MISMATCH AND ARE DETERMINED AT THE PARTING LINE. B S NOTE 3 DIM A B C D E F G K L N P R S INCHES MIN MAX 0.820 0.830 0.395 0.405 0.128 0.148 0.016 0.020 0.088 0.098 0.026 0.032 0.050 BSC 0.035 0.045 0.025 BSC 0.030 0.045 0.435 0.445 0.365 0.375 0.030 0.040 MILLIMETERS MIN MAX 20.83 21.08 10.03 10.29 3.75 3.26 0.50 0.41 2.48 2.24 0.81 0.67 1.27 BSC 1.14 0.89 0.64 BSC 1.14 0.76 11.05 11.30 9.52 9.27 1.01 0.77 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. 81-3-5487-8488 Mfax: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 INTERNET: http://motorola.com/sps MOTOROLA FAST SRAM MCM6726D/D MCM6726D 7