SLRC61002HN,151 - NXP - Datasheet.Online

SLRC610

High-performance ICODE frontend SLRC610 and SLRC610

plus

Rev. 4.6 — 12 September 2018 Product data sheet

227646 COMPANY PUBLIC

1 General description

SLRC610, the low-cost RFID frontend.

The SLRC610 multi-protocol NFC frontend IC supports the following operating modes:

•Read/write mode supporting ISO/IEC 15693

•Read/write mode supporting ICODE EPC UID/ EPC OTP

•Read/write mode supporting ISO/IEC 18000-3 mode 3/ EPC Class-1 HF

The SLRC610 supports the vicinity protocol according to ISO/IEC15693, EPC UID and

ISO/IEC 18000-3 mode 3/ EPC Class-1 HF.

The following host interfaces are supported:

•Serial Peripheral Interface (SPI)

•Serial UART (similar to RS232 with voltage levels dependent on pin voltage supply)

•I2C-bus interface (two versions are implemented: I2C and I2CL)

The SLRC610 supports the connection of a secure access module (SAM). A dedicated

separate I2C interface is implemented for a connection of the SAM. The SAM can be

used for high secure key storage and acts as a very performant crypto coprocessor. A

dedicated SAM is available for connection to the SLRC610.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 2 / 146

2 Features and benefits

•RFID frontend

•Supports ISO/IEC15693, ICODE EPC UID and ISO/IEC 18000-3 mode 3/ EPC Class-1

•Low-power card detection

•Antenna connection with minimum number of external components

•Supported host interfaces:

–SPI up to 10 Mbit/s

–I2C-bus interfaces up to 400 kBd in Fast mode, up to 1000 kBd in Fast mode plus

–RS232 Serial UART up to 1228.8 kBd, with voltage levels dependent on pin voltage

supply

•Separate I2C-bus interface for connection of a secure access module (SAM)

•FIFO buffer with size of 512 byte for highest transaction performance

•Flexible and efficient power saving modes including hard power down, standby and

low-power card detection

•Cost saving by integrated PLL to derive system clock from 27.12 MHz RF quartz crystal

•3 V to 5.5 V power supply (SLRC61002)

2.5 V to 5.5 V power supply (SLRC61003)

•Up to 8 free programmable input/output pins

•The version SLRC61003 offers a more flexible configuration for Low-Power Card

detection compared to the SLRC6102 with the new register LPCD_OPTIONS. In

addition, the SLRC61003 offers new additional settings for the Load Protocol which fit

very well to smaller antennas. The SLRC61003 is therefore the recommended version

for new designs

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 3 / 146

3 Quick reference data

Table 1. Quick reference data SLRC61002HN

Symbol Parameter Conditions Min Typ Max Unit

VDD supply voltage 3.0 5.0 5.5 V

VDD(PVDD) PVDD supply voltage [1] 3.0 5.0 VDD V

VDD(TVDD) TVDD supply voltage 3.0 5.0 5.5 V

Ipd power-down current PDOWN pin pulled HIGH [2] - 8 40 nA

IDD supply current - 17 20 mA

IDD(TVDD) TVDD supply current - 100 250 mA

Tamb operating ambient temperature -25 +25 +85 °C

Tstg storage temperature no supply voltage applied -55 +25 +125 °C

[1] VDD(PVDD) must always be the same or lower voltage than VDD.

[2] Ipd is the sum of all supply currents

Table 2. Quick reference data SLRC61003HN

Symbol Parameter Conditions Min Typ Max Unit

VDD supply voltage 2.5 5.0 5.5 V

VDD(PVDD) PVDD supply voltage [1] 2.5 5.0 VDD V

VDD(TVDD) TVDD supply voltage 2.5 5.0 5.5 V

Ipd power-down current PDOWN pin pulled HIGH [2] - 8 40 nA

IDD supply current - 17 20 mA

- 180 350 mAIDD(TVDD) TVDD supply current

absolute limiting value - - 500 mA

Tamb operating ambient temperature device mounted on PCB which

allows sufficient heat dissipation

-40 +25 +105 °C

Tstg storage temperature no supply voltage applied -55 +25 +125 °C

[1] VDD(PVDD) must always be the same or lower voltage than VDD.

[2] Ipd is the sum of all supply currents

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 4 / 146

4 Ordering information

Table 3. Ordering information

PackageType number

Name Description Version

SLRC61002HN/TRAYB[1]

SLRC61002HN/TRAYBM[2]

SLRC61002HN/T/R[3]

plastic thermal enhanced very thin quad flat package; no

leads; MSL1, 32 terminals + 1 central ground; body 5 × 5

× 0.85 mm

SLRC61003HN/TRAYB[4]

SLRC61003HN/T/R[5]

HVQFN32

plastic thermal enhanced very thin quad flat package; no

leads; MSL2, 32 terminals + 1 central ground; body 5 × 5

× 0.85 mm, wettable flanks

SOT617-1

[1] Delivered in one tray

[2] Delivered in five trays

[3] Delivered on reel with 6000 pieces

[4] Delivered in one tray, MOQ (Minimum order quantity) : 490 pcs

[5] Delivered on reel with 6000 pieces; MOQ (Minimum order quantity) : 6000 pcs

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 5 / 146

5 Block diagram

The analog interface handles the modulation and demodulation of the antenna signals for

the contactless interface.

The contactless UART manages the protocol dependency of the contactless interface

settings managed by the host.

The FIFO buffer ensures fast and convenient data transfer between host and the

contactless UART.

The register bank contains the settings for the analog and digital functionality.

001aaj627

HOST

ANTENNA FIFO

BUFFER

ANALOG

INTERFACE

CONTACTLESS

UART SERIAL UART

SPI

I2C-BUS

Figure 1. Simplified block diagram of the SLRC610

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 6 / 146

6 Pinning information

001aam004

heatsink

Transparent top view

TX1

(1)

DVDD

VDD

TVDD

SIGOUT XTAL1

SIGIN/OUT7 XTAL2

TCK/OUT3 PDOWN

TMS/OUT2 CLKOUT/OUT6

TDI/OUT1 SCL

TDO/OUT0 SDA

AVDD

AUX1

AUX2

RXP

RXN

VMID

TX2

TVSS

8 17

7 18

6 19

5 20

4 21

3 22

2 23

1 24

terminal 1

index area

(1) Pin 33 VSS - heatsink connection

Figure 2. Pinning configuration HVQFN32 (SOT617-1)

6.1 Pin description

Table 4. Pin description

Pin Symbol Type Description

1 TDO / OUT0 O test data output for boundary scan interface / general purpose output 0

2 TDI / OUT1 I test data input boundary scan interface / general purpose output 1

3 TMS / OUT2 I test mode select boundary scan interface / general purpose output 2

4 TCK / OUT3 I test clock boundary scan interface / general purpose output 3

5 SIGIN /OUT7 I/O Contactless communication interface output. / general purpose output 7

6 SIGOUT O Contactless communication interface input.

7 DVDD PWR digital power supply buffer [1]

8 VDD PWR power supply

9 AVDD PWR analog power supply buffer [1]

10 AUX1 O auxiliary outputs: Pin is used for analog test signal

11 AUX2 O auxiliary outputs: Pin is used for analog test signal

12 RXP I receiver input pin for the received RF signal.

13 RXN I receiver input pin for the received RF signal.

14 VMID PWR internal receiver reference voltage [1]

15 TX2 O transmitter 2: delivers the modulated 13.56 MHz carrier

16 TVSS PWR transmitter ground, supplies the output stage of TX1, TX2

17 TX1 O transmitter 1: delivers the modulated 13.56 MHz carrier

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 7 / 146

Pin Symbol Type Description

18 TVDD PWR transmitter voltage supply

19 XTAL1 I crystal oscillator input: Input to the inverting amplifier of the oscillator. This pin is

also the input for an externally generated clock (fosc = 27.12 MHz)

20 XTAL2 O crystal oscillator output: output of the inverting amplifier of the oscillator

21 PDOWN I Power Down (RESET)

22 CLKOUT / OUT6 O clock output / general purpose output 6

23 SCL O Serial Clock line

24 SDA I/O Serial Data Line

25 PVDD PWR pad power supply

26 IFSEL0 / OUT4 I host interface selection 0 / general purpose output 4

27 IFSEL1 / OUT5 I host interface selection 1 / general purpose output 5

28 IF0 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

29 IF1 I/O interface pin, multifunction pin: Can be assigned to host interface SPI, I2C, I2C-L

30 IF2 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

31 IF3 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

32 IRQ O interrupt request: output to signal an interrupt event

33 VSS PWR ground and heat sink connection

[1] This pin is used for connection of a buffer capacitor. Connection of a supply voltage might damage the device.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 8 / 146

7 Functional description

001aam005

I2C,

LOGICAL

FIFO

512 Bytes

REGISTERS

STATEMACHINES

EEPROM

8 kByte

SPI

SAM interface

VOLTAGE

REGULATOR

3/5 V =>

1.8 V

DVDD

POR

ADC PLLLFO

RX OSCTX

VOLTAGE

REGULATOR

3/5 V =>

1.8 V

AVDD

RNG

ANALOGUE FRONT-END

BOUNDARY

SCAN

IF0

IFSEL0

IFSEL1

IF1

IF2

IF3

TCK

TDI

TMS

TDO

RESET

LOGIC PDOWN

I2C

UART

SPI

host interfaces

INTERRUPT

CONTROLLER

IRQ SIGIN

TIMER0..3

CRC

TIMER4

(WAKE-UP

TIMER)

SIGPRO

CODEC

DECOD

CL-

COPRO

SIGIN/

SIGOUT

CONTROL

SIGOUT VMID RXN

RXP

TX1

TX2

XTAL1

XTAL2

SDA

SCL

VDD

VSS

PVDD

TVDD

TVSS

AUX1

AUX2

AVDD

DVDD

CLKOUT

Figure 3. Detailed block diagram of the SLRC610

7.1 Interrupt controller

The interrupt controller handles the enabling/disabling of interrupt requests. All of the

interrupts can be configured by firmware. Additionally, the firmware has possibilities to

trigger interrupts or clear pending interrupt requests. Two 8-bit interrupt registers IRQ0

and IRQ1 are implemented, accompanied by two 8-bit interrupt enable registers IRQ0En

and IRQ1En. A dedicated functionality of bit 7 to set and clear bits 0 to 6 in this interrupt

controller registers is implemented.

The SLRC610 indicates certain events by setting bit IRQ in the register Status1Reg and

additionally, if activated, by pin IRQ. The signal on pin IRQ may be used to interrupt the

host using its interrupt handling capabilities. This allows the implementation of efficient

host software.

Table 4. shows the available interrupt bits, the corresponding source and the condition

for its activation. The interrupt bits Timer0IRQ, Timer1IRQ, Timer2IRQ, Timer3OIRQ, in

underflows.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 9 / 146

The TxIRQ bit in register IRQ0 indicates that the transmission is finished. If the state

changes from sending data to transmitting the end of the frame pattern, the transmitter

unit sets the interrupt bit automatically.

The bit RxIRQ in register IRQ0 indicates an interrupt when the end of the received data is

detected.

The bit IdleIRQ in register IRQ0 is set if a command finishes and the content of the

command register changes to idle.

The register WaterLevel defines both - minimum and maximum warning levels - counting

from top and from bottom of the FIFO by a single value.

The bit HiAlertIRQ in register IRQ0 is set to logic 1 if the HiAlert bit is set to logic 1, that

means the FIFO data number has reached the top level as configured by the register

WaterLevel and bit WaterLevelExtBit.

The bit LoAlertIRQ in register IRQ0 is set to logic 1 if the LoAlert bit is set to logic 1, that

means the FIFO data number has reached the bottom level as configured by the register

WaterLevel.

The bit ErrIRQ in register IRQ0 indicates an error detected by the contactless UART

during receive. This is indicated by any bit set to logic 1 in register Error.

The bit LPCDIRQ in register IRQ0 indicates a card detected.

The bit RxSOFIRQ in register IRQ0 indicates a detection of a SOF or a subcarrier by the

contactless UART during receiving.

The bit GlobalIRQ in register IRQ1 indicates an interrupt occurring at any other interrupt

source when enabled.

Table 5. Interrupt sources

Interrupt bit Interrupt source Is set automatically, when

Timer0IRQ Timer Unit the timer register T0 CounterVal underflows

Timer1IRQ Timer Unit the timer register T1 CounterVal underflows

Timer2IRQ Timer Unit the timer register T2 CounterVal underflows

Timer3IRQ Timer Unit the timer register T3 CounterVal underflows

TxIRQ Transmitter a transmitted data stream ends

RxIRQ Receiver a received data stream ends

IdleIRQ Command Register a command execution finishes

HiAlertIRQ FIFO-buffer pointer the FIFO data number has reached the top level as

configured by the register WaterLevel

LoAlertIRQ FIFO-buffer pointer the FIFO data number has reached the bottom level as

configured by the register WaterLevel

ErrIRQ contactless UART a communication error had been detected

LPCDIRQ LPCD a card was detected when in low-power card detection

mode

RxSOFIRQ Receiver detection of a SOF or a subcarrier

GlobalIRQ all interrupt sources will be set if another interrupt request source is set

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 10 / 146

7.2 Timer module

Timer module overview

The SLRC610 implements five timers. Four timers -Timer0 to Timer3 - have an input

clock that can be configured by register T(x)Control to be 13.56 MHz, 212 kHz, (derived

from the 27.12 MHz quartz) or to be the underflow event of the fifth Timer (Timer4). Each

timer implements a counter register which is 16 bit wide. A reload value for the counter

is defined in a range of 0000h to FFFFh in the registers TxReloadHi and TxReloadLo.

The fifth timer Timer4 is intended to be used as a wakeup timer and is connected to the

internal LFO (Low Frequency Oscillator) as input clock source.

The TControl register allows the global start and stop of each of the four timers Timer0

to Timer3. Additionally, this register indicates if one of the timers is running or stopped.

Each of the five timers implements an individual configuration register set defining timer

reload value (e.g. T0ReloadHi,T0ReloadLo), the timer value (e.g. T0CounterValHi,

T0CounterValLo) and the conditions which define start, stop and clockfrequency (e.g.

T0Control).

The external host may use these timers to manage timing relevant tasks. The timer unit

may be used in one of the following configurations:

•Time-out counter

•Watch-dog counter

•Stop watch

•Programmable one-shot timer

•Periodical trigger

The timer unit can be used to measure the time interval between two events or to

indicate that a specific event has occurred after an elapsed time. The timer register

content is modified by the timer unit, which can be used to generate an interrupt to allow

an host to react on this event.

The counter value of the timer is available in the registers T(x)CounterValHi,

T(x)CounterValLo. The content of these registers is decremented at each timer clock.

If the counter value has reached a value of 0000h and the interrupts are enabled for this

specific timer, an interrupt will be generated as soon as the next clock is received.

If enabled, the timer event can be indicated on the pin IRQ (interrupt request). The bit

Timer(x)IRQ can be set and reset by the host controller. Depending on the configuration,

the timer will stop counting at 0000h or restart with the value loaded from registers

T(x)ReloadHi, T(x)ReloadLo.

The counting of the timer is indicated by bit TControl.T(x)Running.

The timer can be started by setting bits TControl.T(x)Running and

TControl.T(x)StartStopNow or stopped by setting the bits TControl.T(x)StartStopNow and

clearing TControl.T(x)Running.

Another possibility to start the timer is to set the bit T(x)Mode.T(x)Start, this can be useful

if dedicated protocol requirements need to be fulfilled.

7.2.1 Timer modes

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 11 / 146

7.2.1.1 Time-Out- and Watch-Dog-Counter

Having configured the timer by setting register T(x)ReloadValue and starting the counting

of Timer(x) by setting bit TControl.T(x)StartStop and TControl.T(x)Running, the timer unit

decrements the T(x)CounterValue Register beginning with the configured start event. If

the configured stop event occurs before the Timer(x) underflows (e.g. a bit is received

from the card), the timer unit stops (no interrupt is generated).

If no stop event occurs, the timer unit continues to decrement the counter registers

until the content is zero and generates a timer interrupt request at the next clock cycle.

This allows to indicate to a host that the event did not occur during the configured time

interval.

7.2.1.2 Wake-up timer

The wake-up Timer4 allows to wakeup the system from standby after a predefined time.

The system can be configured in such a way that it is entering the standby mode again in

case no card had been detected.

This functionality can be used to implement a low-power card detection (LPCD). For

the low-power card detection it is recommended to set T4Control.T4AutoWakeUp and

T4Control.T4AutoRestart, to activate the Timer4 and automatically set the system

in standby. The internal low frequency oscillator (LFO) is then used as input clock

for this Timer4. If a card is detected the host-communication can be started. If bit

T4Control.T4AutoWakeUp is not set, the SLRC610 will not enter the standby mode again

in case no card is detected but stays fully powered.

7.2.1.3 Stop watch

If an underflow occurred which can be identified by evaluating the corresponding IRQ bit,

the performed time measurement according to the formula above is not correct.

The elapsed time between a configured start- and stop event may be measured by the

CLRC663 timer unit. By setting the registers T(x)ReloadValueHi, T(x)reloadValueLo the

timer starts to decrement as soon as activated. If the configured stop event occurs, the

timer stops decrementing. The elapsed time between start and stop event can then be

calculated by the host dependent on the timer interval TTimer:

(1)

If an underflow occurred which can be identified by evaluating the corresponding IRQ bit,

the performed time measurement according to the formula above is not correct.

7.2.1.4 Programmable one-shot timer

The host configures the interrupt and the timer, starts the timer and waits for the interrupt

event on pin IRQ. After the configured time the interrupt request will be raised.

7.2.1.5 Periodical trigger

If the bit T(x)Control.T(x)AutoRestart is set and the interrupt is activated, an interrupt

request will be indicated periodically after every elapsed timer period.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 12 / 146

7.3 Contactless interface unit

The contactless interface unit of the SLRC610 supports the following read/write operating

modes:

•ISO/IEC15693/ICODE

•ICODE EPC UID

•ISO/IEC 18000-3 mode 3/ EPC Class-1 HF

aaa-002468

BATTERY/POWER SUPPLY

reader/writer

MICROCONTROLLER

READER IC ISO/IEC 15693 TAG

Figure 4. Read/write mode

A typical system using the SLRC610 is using a microcontroller to implement the higher

levels of the contactless communication protocol and a power supply (battery or external

supply).

7.3.1 ISO/IEC15693 functionality

The physical parameters are described in Table 5.

Table 6. Communication overview for ISO/IEC 15693 reader/writer reader to label

Transfer speedCommunication

direction

Signal type

fc / 8192 kbit/s fc / 512 kbit/s

reader side

modulation

10 % to 30 % ASK or

100 % ASK

10 % to 30 % ASK 90 %

to 100 % ASK

bit encoding 1/256 1/4

Reader to label

(send data from the

SLRC610 to a card)

data rate 1,66 kbit/s 26,48kbit/s

Table 7. Communication overview for ISO/IEC 15693 reader/writer label to reader

Transfer speedCommunication

direction

Signal type

6.62 (6.67)

kbit/s

13.24 kbit/s[1] 26.48

(26.69) kbit/s

52.96 kbit/s

card side

modulation

not

supported

not supported single (dual)

subcarrier load

modulation

ASK

single

subcarrier

load

modulation

ASK

bit length

(μs)

- - 37.76 (37.46) 18.88

Label to reader

(SLRC610

receives data

from a card)

fc = 13.56 MHz

bit encoding - - Manchester

coding

Manchester

coding

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 13 / 146

Transfer speedCommunication

direction

Signal type

6.62 (6.67)

kbit/s

13.24 kbit/s[1] 26.48

(26.69) kbit/s

52.96 kbit/s

subcarrier

frequency

[MHz]

- - fc / 32 (fc / 28) fc / 32

[1] Fast inventory (page) read command only (ICODE proprietary command).

001aam272

pulse

modulated

carrier

~9.44 µs

0 1 2 3 4

~18.88 µs

. 2 . . . ..... . . . . . . . . . 22..... 2 2

2 55 5 5

5~4,833 ms 32 4 5

Figure 5. Data coding according to ISO/IEC 15693. standard mode reader to label

7.3.2 EPC-UID/UID-OTP functionality

The physical parameters are described in Table 7.

Table 8. Communication overview for EPC/UID

Transfer speedCommunication

direction

Signal type

26.48 kbit/s 52.96 kbit/s

reader side modulation 10 % to 30 % ASK

bit encoding RTZ

Reader to card

(send data from the

SLRC610 to a card)

bit length 37.76 μs

card side modulation single subcarrier load

modulation

bit length 18.88 μs

Card to reader

(SLRC610 receives

data from a card)

bit encoding Manchester coding

Data coding and framing according to EPC global 13.56 MHz ISM (industrial, scientific

and medical) Band Class 1 Radio Frequency Identification Tag Interface Specification

(Candidate Recommendation, Version 1.0.0).

7.3.3 ISO/IEC 18000-3 mode 3/ EPC Class-1 HF functionality

The ISO/IEC 18000-3 mode 3/ EPC Class-1 HF is not described in this document. For a

detailed explanation of the protocol, refer to the ISO/IEC 18000-3 mode 3/ EPC Class-1

HF standard.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 14 / 146

7.3.3.1 Data encoding ICODE

The ICODE protocols have mainly three different methods of data encoding:

•"1" out of "4" coding scheme

•"1" out of "256" coding scheme

•"Return to Zero" (RZ) coding scheme

Data encoding for all three coding schemes is done by the ICODE generator.

The supported EPC Class-1 HF modes are:

•2 pulse for 424 kbit subcarrier

•4 pulse for 424 kbit subcarrier

•2 pulse for 848 kbit subcarrier

•4 pulse for 848 kbit subcarrier

7.4 Host interfaces

7.4.1 Host interface configuration

The SLRC610 supports direct interfacing of various hosts as the SPI, I2C, I2CL and

serial UART interface type. The SLRC610 resets its interface and checks the current

host interface type automatically having performed a power-up or resuming from power

down. The SLRC610 identifies the host interface by the means of the logic levels on

the control pins after the Cold Reset Phase. This is done by a combination of fixed

pin connections.The following table shows the possible configurations defined by

IFSEL1,IFSEL0:

Table 9. Connection scheme for detecting the different interface types

Pin Pin Symbol UART SPI I2C I2C-L

28 IF0 RX MOSI ADR1 ADR1

29 IF1 n.c. SCK SCL SCL

30 IF2 TX MISO ADR2 SDA

31 IF3 PAD_VDD NSS SDA ADR2

26 IFSEL0 VSS VSS PAD_VDD PAD_VDD

27 IFSEL1 VSS PAD_VDD VSS PAD_VDD

7.4.2 SPI interface

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 15 / 146

7.4.2.1 General

001aal998

READER IC

IF1

SCK

IF0

MOSI

IF2

MISO

IF3

NSS

Figure 6. Connection to host with SPI

The SLRC610 acts as a slave during the SPI communication. The SPI clock SCK has to

be generated by the master. Data communication from the master to the slave uses the

Line MOSI. Line MISO is used to send data back from the SLRC610 to the master.

A serial peripheral interface (SPI compatible) is supported to enable high speed

communication to a host. The implemented SPI compatible interface is according to a

standard SPI interface. The SPI compatible interface can handle data speed of up to

10 Mbit/s. In the communication with a host SLRC610 acts as a slave receiving data

from the external host for register settings and to send and receive data relevant for the

communication on the RF interface.

NSS (Not Slave Select) enables or disables the SPI interface. When NSS is logical high,

the interface is disabled and reset. Between every SPI command the NSS must go to

logical high to be able to start the next command read or write.

On both data lines (MOSI, MISO) each data byte is sent by MSB first. Data on MOSI

line shall be stable on rising edge of the clock line (SCK) and is allowed to change on

falling edge. The same is valid for the MISO line. Data is provided by the SLRC610 on

the falling edge and is stable on the rising edge.The polarity of the clock is low at SPI

idle.

7.4.2.2 Read data

To read out data from the SLRC610 by using the SPI compatible interface the following

byte order has to be used.

The first byte that is sent defines the mode (LSB bit) and the address.

Table 10. Byte Order for MOSI and MISO

byte 0 byte 1 byte 2 byte 3 to n-1 byte n byte n+1

MOSI address 0 address 1 address 2 …….. address n 00h

MISO X data 0 data 1 …….. data n - 1 data n

Remark: The Most Significant Bit (MSB) has to be sent first.

7.4.2.3 Write data

To write data to the SLRC610 using the SPI interface the following byte order has to

be used. It is possible to write more than one byte by sending a single address byte

(see.8.5.2.4).

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 16 / 146

The first send byte defines both, the mode itself and the address byte.

Table 11. Byte Order for MOSI and MISO

byte 0 byte 1 byte 2 3 to n-1 byte n byte n + 1

MOSI address 0 data 0 data 1 …….. data n - 1 data n

MISO X X X …….. X X

Remark: The Most Significant Bit (MSB) has to be sent first.

7.4.2.4 Address byte

The address byte has to fulfil the following format:

The LSB bit of the first byte defines the used mode. To read data from the SLRC610 the

LSB bit is set to logic 1. To write data to the SLRC610 the LSB bit has to be cleared. The

bits 6 to 0 define the address byte.

NOTE: When writing the sequence [address byte][data0][data1][data2]..., [data0] is

written to address [address byte], [data1] is written to address [address byte + 1] and

[data2] is written to [address byte + 2].

Exception: This auto increment of the address byte is not performed if data is written to

the FIFO address

Table 12. Address byte 0 register; address MOSI

76543210

address 6 address 5 address 4 address 3 address 2 address 1 address 0 1 (read)

0 (write)

MSB LSB

7.4.2.5 Timing Specification SPI

The timing condition for SPI interface is as follows:

Table 13. Timing conditions SPI

Symbol Parameter Min Typ Max Unit

tSCKL SCK LOW time 50 - - ns

tSCKH SCK HIGH time 50 - - ns

th(SCKH-D) SCK HIGH to data input hold time 25 - - ns

tsu(D-SCKH) data input to SCK HIGH set-up time 25 - - ns

th(SCKL-Q) SCK LOW to data output hold time - - 25 ns

t(SCKL-NSSH) SCK LOW to NSS HIGH time 0 - - ns

tNSSH NSS HIGH time 50 - - ns

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 17 / 146

aaa-016093

tSCKL

tNSSH tSCKH tSCKL

tsu(D-SCKH) th(SCKH-D)

th(SCKL-Q)

t(SCKL-NSSH)

SCK

MOSI

MISO

MSB

LSB

NSS

Figure 7. Connection to host with SPI

Remark: To send more bytes in one data stream the NSS signal must be LOW during

the send process. To send more than one data stream the NSS signal must be HIGH

between each data stream.

7.4.3 RS232 interface

7.4.3.1 Selection of the transfer speeds

The internal UART interface is compatible to a RS232 serial interface. The levels

supplied to the pins are between VSS and PVDD. To achieve full compatibility of the

voltage levels to the RS232 specification, a RS232 level shifter is required.

Table 14 "Selectable transfer speeds" describes examples for different transfer speeds

and relevant register settings. The resulting transfer speed error is less than 1.5 % for all

described transfer speeds. The default transfer speed is 115.2 kbit/s.

To change the transfer speed, the host controller has to write a value for the new transfer

speed to the register SerialSpeedReg. The bits BR_T0 and BR_T1 define factors to set

the transfer speed in the SerialSpeedReg.

Table 13 "Settings of BR_T0 and BR_T1" describes the settings of BR_T0 and BR_T1.

Table 14. Settings of BR_T0 and BR_T1

BR_T0 01234567

factor BR_T0 1 1 2 4 8 16 32 64

range BR_T1 1 to 32 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64

Table 15. Selectable transfer speeds

Serial SpeedRegTransfer speed (kbit/s)

(Hex.)

Transfer speed accuracy (%)

7.2 FA -0.25

9.6 EB 0.32

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 18 / 146

Serial SpeedRegTransfer speed (kbit/s)

(Hex.)

Transfer speed accuracy (%)

14.4 DA -0.25

19.2 CB 0.32

38.4 AB 0.32

57.6 9A -0.25

115.2 7A -0.25

128 74 -0.06

230.4 5A -0.25

460.8 3A -0.25

921.6 1C 1.45

1228.8 15 0.32

The selectable transfer speeds as shown are calculated according to the following

formulas:

if BR_T0 = 0: transfer speed = 27.12 MHz / (BR_T1 + 1)

if BR_T0 > 0: transfer speed = 27.12 MHz / (BR_T1 + 33)/2(BR_T0 - 1)

Remark: Transfer speeds above 1228.8 kBits/s are not supported.

7.4.3.2 Framing

Table 16. UART framing

Bit Length Value

Start bit (Sa) 1 bit 0

Data bits 8 bit Data

Stop bit (So) 1 bit 1

Remark: For data and address bytes the LSB bit has to be sent first. No parity bit is

used during transmission.

Read data: To read out data using the UART interface the flow described below has to

be used. The first send byte defines both the mode itself and the address.The Trigger on

pin IF3 has to be set, otherwise no read of data is possible.

Table 17. Byte Order to Read Data

Mode byte 0 byte 1

RX address -

TX - data 0

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 19 / 146

001aam298

A0 A1Sa A2 A3

RX A4 A5 A6 RD/

NWR

DATA

ADDRESS

D1Sa D2 D3 D4 D5 D6 D7 So

Figure 8. Example for UART Read

Write data:

To write data to the SLRC610 using the UART interface the following sequence has to be

used.

The first send byte defines both, the mode itself and the address.

Table 18. Byte Order to Write Data

Mode byte 0 byte 1

RX address 0 data 0

TX address 0

001aam299

A0 A1Sa A2 A3

RX A4 A5 A6 RD/

NWR

ADDRESS

A1Sa A2 A3 A4 A5 A6 RD/

NWR

DATA

D1Sa D2 D3 D4 D5 D6 D7 So

Figure 9. Example diagram for a UART write

Remark: Data can be sent before address is received.

7.4.4 I2C-bus interface

7.4.4.1 General

An Inter IC (I2C) bus interface is supported to enable a low cost, low pin count serial bus

interface to the host. The implemented I2C interface is mainly implemented according the

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 20 / 146

NXP Semiconductors I2C interface specification, rev. 3.0, June 2007. The SLRC610 can

act as a slave receiver or slave transmitter in standard mode, fast mode and fast mode

plus.

The following features defined by the NXP Semiconductors I2C interface specification,

rev. 3.0, June 2007 are not supported:

•The SLRC610 I2C interface does not stretch the clock

•The SLRC610 I2C interface does not support the general call. This means that the

SLRC610 does not support a software reset

•The SLRC610 does not support the I2C device ID

•The implemented interface can only act in slave mode. Therefore no clock generation

and access arbitration is implemented in the SLRC610.

•High speed mode is not supported by the SLRC610

001aam000

READER IC

SDA

SCL

PULL-UP

NETWORK

PULL-UP

NETWORK

MICROCONTROLLER

Figure 10. I2C-bus interface

The voltage level on the I2C pins is not allowed to be higher than PVDD.

SDA is a bidirectional line, connected to a positive supply voltage via a pull-up resistor.

Both lines SDA and SCL are set to HIGH level if no data is transmitted. Data on the I2C-

bus can be transferred at data rates of up to 400 kbit/s in fast mode, up to 1 Mbit/s in the

fast mode+.

If the I2C interface is selected, a spike suppression according to the I2C interface

specification on SCL and SDA is automatically activated.

For timing requirements refer to Table 200 "I2C-bus timing in fast mode and fast mode

plus"

7.4.4.2 I2C Data validity

Data on the SDA line shall be stable during the HIGH period of the clock. The HIGH state

or LOW state of the data line shall only change when the clock signal on SCL is LOW.

001aam300

data line stable;

data valid

change

of data

allowed

SDA

SCL

Figure 11. Bit transfer on the I2C-bus.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 21 / 146

7.4.4.3 I2C START and STOP conditions

To handle the data transfer on the I2C-bus, unique START (S) and STOP (P) conditions

are defined.

A START condition is defined with a HIGH-to-LOW transition on the SDA line while SCL

is HIGH.

A STOP condition is defined with a LOW-to-HIGH transition on the SDA line while SCL is

HIGH.

The master always generates the START and STOP conditions. The bus is considered to

be busy after the START condition. The bus is considered to be free again a certain time

after the STOP condition.

The bus stays busy if a repeated START (Sr) is generated instead of a STOP condition.

In this respect, the START (S) and repeated START (Sr) conditions are functionally

identical. Therefore, the S symbol will be used as a generic term to represent both the

START and repeated START (Sr) conditions.

001aam301

START condition

SCL

SDA

SCL

SDA

STOP condition

Figure 12. START and STOP conditions

7.4.4.4 I2C byte format

Each byte has to be followed by an acknowledge bit. Data is transferred with the MSB

first, see Figure 12 "START and STOP conditions". The number of transmitted bytes

during one data transfer is unrestricted but shall fulfil the read/write cycle format.

7.4.4.5 I2C Acknowledge

An acknowledge at the end of one data byte is mandatory. The acknowledge-related

clock pulse is generated by the master. The transmitter of data, either master or slave,

releases the SDA line (HIGH) during the acknowledge clock pulse. The receiver shall pull

down the SDA line during the acknowledge clock pulse so that it remains stable LOW

during the HIGH period of this clock pulse.

The master can then generate either a STOP (P) condition to stop the transfer, or a

repeated START (Sr) condition to start a new transfer.

A master-receiver shall indicate the end of data to the slave- transmitter by not

generating an acknowledge on the last byte that was clocked out by the slave. The slave-

transmitter shall release the data line to allow the master to generate a STOP (P) or

repeated START (Sr) condition.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 22 / 146

001aam302

clock pulse for

acknowledgement

SCL FROM

MASTER

DATA OUTPUT

BY RECEIVERER

DATA OUTPUT

BY TRANSMITTER

2 8 9

acknowledge

START

condition

not acknowledge

Figure 13. Acknowledge on the I2C- bus

001aam303

MSB acknowledgement

signal from slave

acknowledgement

signal from receiver

clock line held low while

interrupts are serviced

byte complete,

interrupt within slave

1 2 7 8 9 1 2 9

ACK ACK

3 - 8 Sr

Figure 14. Data transfer on the I2C- bus

7.4.4.6 I2C 7-bit addressing

During the I2C-bus addressing procedure, the first byte after the START condition is used

to determine which slave will be selected by the master.

Alternatively the I2C address can be configured in the EEPROM. Several address

numbers are reserved for this purpose. During device configuration, the designer has to

ensure, that no collision with these reserved addresses in the system is possible. Check

the corresponding I2C specification for a complete list of reserved addresses.

For all SLRC610 devices the upper 5 bits of the device bus address are reserved by NXP

and set to 01010(bin). The remaining 2 bits (ADR_2, ADR_1) of the slave address can

be freely configured by the customer in order to prevent collisions with other I2C devices

by using the interface pins (refer to Table 8) or the value of the I2C address EEPROM

001aam304

Bit 6 Bit 5 Bit 4

slave address

Bit 3 Bit 2 Bit 1 Bit 0 R/W

MSB LSB

Figure 15. First byte following the START procedure

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 23 / 146

7.4.4.7 I2C-register write access

To write data from the host controller via I2C to a specific register of the SLRC610 the

following frame format shall be used.

The read/write bit shall be set to logic 0.

The first byte of a frame indicates the device address according to the I2C rules. The

second byte indicates the register address followed by up to n-data bytes. In case the

address indicates the FIFO, in one frame all n-data bytes are written to the FIFO register

address. This enables for example a fast FIFO access.

7.4.4.8 I2C-register read access

To read out data from a specific register address of the SLRC610 the host controller shall

use the procedure:

First a write access to the specific register address has to be performed as indicated in

the following frame:

The first byte of a frame indicates the device address according to the I2C rules. The

second byte indicates the register address. No data bytes are added.

The read/write bit shall be logic 0.

Having performed this write access, the read access starts. The host sends the device

address of the SLRC610. As an answer to this device address the SLRC610 responds

with the content of the addressed register. In one frame n-data bytes could be read

using the same register address. The address pointing to the register is incremented

automatically (exception: FIFO register address is not incremented automatically).

This enables a fast transfer of register content. The address pointer is incremented

automatically and data is read from the locations [address], [address+1], [address+2]...

[address+(n-1)]

In order to support a fast FIFO data transfer, the address pointer is not incremented

automatically in case the address is pointing to the FIFO.

The read/write bit shall be set to logic 1.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 24 / 146

001aam305

Ack

(W) Ack 0SA I2C slave address

A7-A0

Frontend IC register

address A6-A0 Ack

DATA

[7..0]

[0..n]

Ack

(W) Ack

Optional, if the previous access was on the same register address

Read Cycle

Write Cycle

0SA I2C slave address

A7-A0

Frontend IC register

address A6-A0

(R) AckSA

sent by master

sent by slave

I2C slave address

A7-A0 Ack

DATA

[7..0]

[0..n]

0..n

Nack

DATA

[7..0]

Figure 16. Register read and write access

7.4.4.9 I2CL-bus interface

The SLRC610 provides an additional interface option for connection of a SAM. This

logical interface fulfills the I2C specification, but the rise/fall timings will not be compliant

to the I2C standard. The I2CL interface uses standard I/O pads, and the communication

speed is limited to 5 MBaud. The protocol itself is equivalent to the fast mode protocol of

I2C. The SCL levels are generated by the host in push/pull mode. The RC610 does not

stretch the clock. During the high period of SCL the status of the line is maintained by a

bus keeper.

The address is 01010xxb, where the last two bits of the address can be defined by the

application. The definition of this bits can be done by two options. With a pin, where the

higher bit is fixed to 0 or the configuration can be defined via EEPROM. Refer to the

EEPROM configuration in Section 7.7.

Table 19. Timing parameter I2CL

Parameter Min Max Unit

fSCL 0 5 MHz

tHD;STA 80 - ns

tLOW 100 - ns

tHIGH 100 - ns

tSU;SDA 80 - ns

tHD;DAT 0 50 ns

tSU;DAT 0 20 ns

tSU;STO 80 - ns

tBUF 200 - ns

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 25 / 146

The pull-up resistor is not required for the I2CL interface. Instead, a on chip buskeeper

is implemented in the SLRC610 for SDA of the I2CL interface. This protocol is intended

to be used for a point to point connection of devices over a short distance and does

not support a bus capability.The driver of the pin must force the line to the desired

logic voltage. To avoid that two drivers are pushing the line at the same time following

regulations must be fulfilled:

SCL: As there is no clock stretching, the SCL is always under control of the Master.

SDA: The SDA line is shared between master and slave. Therefore the master and the

slave must have the control over the own driver enable line of the SDA pin. The following

rules must be followed:

•In the idle phase the SDA line is driven high by the master

•In the time between start and stop condition the SDA line is driven by master or slave

when SCL is low. If SCL is high the SDA line is not driven by any device

•To keep the value on the SDA line a on chip buskeeper structure is implemented for

the line

7.4.5 SAM interface

7.4.5.1 SAM functionality

The SLRC610 implements a dedicated I2C or SPI interface to integrate a SAM (Secure

Access Module) in a very convenient way into applications (e.g. a proximity reader).

The SAM can be connected to the microcontroller to operate like a cryptographic co-

processor. For any cryptographic task, the microcontroller requests a operation from the

SAM, receives the answer and sends it over a host interface (e.g. I2C, SPI) interface to

the connected reader IC.

7.4.5.2 SAM connection

The SLRC610 provides an interface to connect a SAM dedicated to the SLRC610. Both

interface options of the SLRC610, I2C, I2CL or SPI can be used for this purpose. The

interface option of the SAM itself is configured by a host command sent from the host to

the SAM.

The I2CL interface is intended to be used as connection between two IC’s over a short

distance. The protocol fulfills the I2C specification, but does support a single device

connected to the bus only.

The SPI block for SAM connection is identical with the SPI host interface block.

The pins used for the SAM SPI are described in Table 19.

Table 20. SPI SAM connection

SPI functionality PIN

MISO SDA2

SCL SCL2

MOSI IFSEL1

NSS IFSEL0

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 26 / 146

7.4.6 Boundary scan interface

The SLRC610 provides a boundary scan interface according to the IEEE 1149.1. This

interface allows to test interconnections without using physical test probes. This is done

by test cells, assigned to each pin, which override the functionality of this pin.

To be able to program the test cells, the following commands are supported:

Table 21. Boundary scan command

Value

(decimal)

Command Parameter in Parameter out

0 bypass - -

1 preload data (24) -

1 sample - data (24)

2 ID code (default) - data (32)

3 USER code - data (32)

4 Clamp - -

5 HIGH Z - -

7 extest data (24) data (24)

8 interface on/off interface (1) -

9 register access read address (7) data (8)

10 register access write address (7) - data (8) -

The Standard IEEE 1149.1 describes the four basic blocks necessary to use this

interface: Test Access Port (TAP), TAP controller, TAP instruction register, TAP data

7.4.6.1 Interface signals

The boundary scan interface implements a four line interface between the chip and the

environment. There are three Inputs: Test Clock (TCK); Test Mode Select (TMS); Test

Data Input (TDI) and one output Test Data Output (TDO). TCK and TMS are broadcast

signals, TDI to TDO generate a serial line called Scan path.

Advantage of this technique is that independent of the numbers of boundary scan

devices the complete path can be handled with four signal lines.

The signals TCK, TMS are directly connected with the boundary scan controller. Because

these signals are responsible for the mode of the chip, all boundary scan devices in one

scan path will be in the same boundary scan mode.

7.4.6.2 Test Clock (TCK)

The TCK pin is the input clock for the module. If this clock is provided, the test logic

is able to operate independent of any other system clocks. In addition, it ensures that

multiple boundary scan controllers that are daisy-chained together can synchronously

communicate serial test data between components. During normal operation, TCK

is driven by a free-running clock. When necessary, TCK can be stopped at 0 or 1 for

extended periods of time. While TCK is stopped at 0 or 1, the state of the boundary scan

controller does not change and data in the Instruction and Data Registers is not lost.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 27 / 146

The internal pull-up resistor on the TCK pin is enabled. This assures that no clocking

occurs if the pin is not driven from an external source.

7.4.6.3 Test Mode Select (TMS)

The TMS pin selects the next state of the boundary scan controller. TMS is sampled on

the rising edge of TCK. Depending on the current boundary scan state and the sampled

value of TMS, the next state is entered. Because the TMS pin is sampled on the rising

edge of TCK, the IEEE Standard 1149.1 expects the value on TMS to change on the

falling edge of TCK.

Holding TMS high for five consecutive TCK cycles drives the boundary scan controller

state machine to the Test-Logic-Reset state. When the boundary scan controller enters

the Test-Logic-Reset state, the Instruction Register (IR) resets to the default instruction,

IDCODE. Therefore, this sequence can be used as a reset mechanism.

The internal pull-up resistor on the TMS pin is enabled.

7.4.6.4 Test Data Input (TDI)

The TDI pin provides a stream of serial information to the IR chain and the DR chains.

TDI is sampled on the rising edge of TCK and, depending on the current TAP state and

the current instruction, presents this data to the proper shift register chain. Because the

TDI pin is sampled on the rising edge of TCK, the IEEE Standard 1149.1 expects the

value on TDI to change on the falling edge of TCK.

The internal pull-up resistor on the TDI pin is enabled.

7.4.6.5 Test Data Output (TDO)

The TDO pin provides an output stream of serial information from the IR chain or the

DR chains. The value of TDO depends on the current TAP state, the current instruction,

and the data in the chain being accessed. In order to save power when the port is not

being used, the TDO pin is placed in an inactive drive state when not actively shifting out

data. Because TDO can be connected to the TDI of another controller in a daisy-chain

configuration, the IEEE Standard 1149.1 expects the value on TDO to change on the

falling edge of TCK.

7.4.6.6 Data register

According to the IEEE1149.1 standard there are two types of data register defined:

bypass and boundary scan

The bypass register enable the possibility to bypass a device when part of the scan

path.Serial data is allowed to be transferred through a device from the TDI pin to the

TDO pin without affecting the operation of the device.

The boundary scan register is the scan-chain of the boundary cells. The size of this

7.4.6.7 Boundary scan cell

The boundary scan cell opens the possibility to control a hardware pin independent of its

normal use case. Basically the cell can only do one of the following: control, output and

input.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 28 / 146

001aam306

TAP

LOG

TAP

IC1 IC2

TCK TMSTCK TMS

TDOTDO

Boundary scan cell

TDITDI

Figure 17. Boundary scan cell path structure

7.4.6.8 Boundary scan path

This chapter shows the boundary scan path of the SLRC610.

Table 22. Boundary scan path of the SLRC610

Number (decimal) Cell Port Function

23 BC_1 - Control

22 BC_8 CLKOUT Bidir

21 BC_1 - Control

20 BC_8 SCL2 Bidir

19 BC_1 - Control

18 BC_8 SDA2 Bidir

17 BC_1 - Control

16 BC_8 IFSEL0 Bidir

15 BC_1 - Control

14 BC_8 IFSEL1 Bidir

13 BC_1 - Control

12 BC_8 IF0 Bidir

11 BC_1 - Control

10 BC_8 IF1 Bidir

9 BC_1 - Control

8 BC_8 IF2 Bidir

7 BC_1 IF2 Output2

6 BC_4 IF3 Bidir

5 BC_1 - Control

4 BC_8 IRQ Bidir

3 BC_1 - Control

2 BC_8 SIGIN Bidir

1 BC_1 - Control

0 BC_8 SIGOUT Bidir

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 29 / 146

Refer to the SLRC610 BSDL file.

7.4.6.9 Boundary Scan Description Language (BSDL)

All of the boundary scan devices have a unique boundary structure which is necessary to

know for operating the device. Important components of this language are:

•available test bus signal

•compliance pins

•command register

•data register

•boundary scan structure (number and types of the cells, their function and the

connection to the pins.)

The SLRC610 is using the cell BC_8 for the IO-Lines. The I2C Pin is using a BC_4 cell.

For all pad enable lines the cell BC1 is used.

The manufacturer's identification is 02Bh.

•attribute IDCODEISTER of SLRC610: entity is "0001" and -- version

•"0011110010000010b" and -- part number (3C82h)

•"00000010101b" and -- manufacturer (02Bh)

•"1b"; -- mandatory

The user code data is coded as followed:

•product ID (3 bytes)

•version

These four bytes are stored as the first four bytes in the EEPROM.

7.4.6.10 Non-IEEE1149.1 commands

Interface on/off: With this command the host/SAM interface can be deactivated and the

Read and Write command of the boundary scan interface is activated. (Data = 1). With

Update-DR the value is taken over.

Shifting the DR is shifting in a new address. With Update-DR this address is taken over

into the actual address.

the DR. The data is copied into the internal register at the given address.

7.5 Buffer

7.5.1 Overview

An 512 × 8-bit FIFO buffer is implemented in the SLRC610. It buffers the input and output

data stream between the host and the internal state machine of the SLRC610. Thus, it

is possible to handle data streams with lengths of up to 512 bytes without taking timing

constraints into account. The FIFO can also be limited to a size of 255 byte. In this case

all the parameters (FIFO length, Watermark...) require a single byte only for definition. In

case of a 512 byte FIFO length the definition of this values requires 2 bytes.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 30 / 146

7.5.2 Accessing the FIFO buffer

When the μ-Controller starts a command, the SLRC610 may, while the command is in

progress, access the FIFO-buffer according to that command. Physically only one FIFO-

buffer is implemented, which can be used in input and output direction. Therefore the μ-

Controller has to take care, not to access the FIFO buffer in a way that corrupts the FIFO

data.

7.5.3 Controlling the FIFO buffer

Besides writing to and reading from the FIFO buffer, the FIFO-buffer pointers might be

reset by setting the bit FIFOFlush in FIFOControl to 1. Consequently, the FIFOLevel bits

are set to logic 0, the actually stored bytes are not accessible any more and the FIFO

buffer can be filled with another 512 bytes (or 255 bytes if the bit FIFOSize is set to 1)

again.

7.5.4 Status Information about the FIFO buffer

The host may obtain the following data about the FIFO-buffers status:

•Number of bytes already stored in the FIFO-buffer. Writing increments, reading

decrements the FIFO level: FIFOLength in register FIFOLength (and FIFOControl

•Warning, that the FIFO-buffer is almost full: HiAlert in register FIFOControl according

to the value of the water level in register WaterLevel (Register 02h bit [2], Register 03h

bit[7:0])

•Warning, that the FIFO-buffer is almost empty: LoAlert in register FIFOControl

according to the value of the water level in register WaterLevel (Register 02h bit [2],

•FIFOOvl bit indicates, that bytes were written to the FIFO buffer although it was already

full: ErrIRQ in register IRQ0.

WaterLevel is one single value defining both HiAlert (counting from the FIFO top) and

LoAlert (counting from the FIFO bottom). The SLRC610 can generate an interrupt signal

if:

•LoAlertIRQEn in register IRQ0En is set to logic 1 it will activate pin IRQ when LoAlert in

the register FIFOControl changes to 1.

•HiAlertIRQEN in register IRQ0En is set to logic 1 it will activate pin IRQ when HiAlert in

the register FIFOControl changes to 1.

The bit HiAlert is set to logic 1 if maximum water level bytes (as set in register

WaterLevel) or less can be stored in the FIFO-buffer. It is generated according to the

following equation:

(2)

The bit LoAlert is set to logic 1 if water level bytes (as set in register WaterLevel) or less

are actually stored in the FIFO-buffer. It is generated according to the following equation:

(3)

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 31 / 146

7.6 Analog interface and contactless UART

7.6.1 General

The integrated contactless UART supports the external host online with framing and

error checking of the protocol requirements up to 848 kbit/s. An external circuit can be

connected to the communication interface pins SIGIN and SIGOUT to modulate and

demodulate the data.

The contactless UART handles the protocol requirements for the communication

schemes in co-operation with the host. The protocol handling itself generates bit- and

byte-oriented framing and handles error detection like Parity and CRC according to the

different contactless communication schemes.

The size, the tuning of the antenna, and the supply voltage of the output drivers have an

impact on the achievable field strength. The operating distance between reader and card

depends additionally on the type of card used.

7.6.2 TX transmitter

The signal delivered on pin TX1 and pin TX2 is the 13.56 MHz carrier modulated by an

envelope signal for energy and data transmission. It can be used to drive an antenna

directly, using a few passive components for matching and filtering, see Section 13

"Application information". The signal on TX1 and TX2 can be configured by the register

DrvMode, see Section 8.8.1 "TxMode".

The modulation index can be set by the TxAmp.

Following figure shows the general relations during modulation

001aan355

time

influenced by set_clk_mode envelope

TX ASK100

1: Defined by set_cw_amplitude.

2: Defined by set_residual_carrier.

TX ASK10 (1)

(2)

Figure 18. General dependences of modulation

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 32 / 146

Note: When changing the continuous carrier amplitude, the residual carrier amplitude

also changes, while the modulation index remains the same.

The registers Section 8.8 and Section 8.10 control the data rate, the framing during

transmission and the setting of the antenna driver to support the requirements at the

different specified modes and transfer speeds.

Table 23. Settings for TX1 and TX2

TxClkMode

(binary)

Tx1 and TX2 output Remarks

000 High impedance -

001 0 output pulled to 0 in any case

010 1 output pulled to 1 in any case

110 RF high side push open drain, only high side (push) MOS supplied

with clock, clock parity defined by invtx; low

side MOS is off

101 RF low side pull open drain, only low side (pull) MOS supplied

with clock, clock parity defined by invtx; high

side MOS is off

111 13.56 MHz clock derived

from 27.12 MHz quartz

divided by 2

push/pull Operation, clock polarity defined by

invtx; setting for 10% modulation

Table 24. Setting residual carrier and modulation index by TXamp.set_residual_carrier

set_residual_carrier (decimal) residual carrier [%] modulation index [%]

0 99 0.5

1 98 1.0

2 96 2.0

3 94 3.1

4 91 4.7

5 89 5.8

6 87 7.0

7 86 7.5

8 85 8.1

9 84 8.7

10 83 9.3

11 82 9.9

12 81 10.5

13 80 11.1

14 79 11.7

15 78 12.4

16 77 13.0

17 76 13.6

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 33 / 146

set_residual_carrier (decimal) residual carrier [%] modulation index [%]

18 75 14.3

19 74 14.9

20 72 16.3

21 70 17.6

22 68 19.0

23 65 21.2

24 60 25.0

25 55 29.0

26 50 33.3

27 45 37.9

28 40 42.9

29 35 48.1

30 30 53.8

31 25 60.0

Note: At VDD(TVDD) <5 V and residual carrier settings <50%, the accuracy of the

modulation index may be low in dependency of the antenna tuning impedance

7.6.2.1 Overshoot protection

The SLRC610 provides an overshoot protection for 100% ASK to avoid overshoots

during a PCD communication. Therefore two timers overshoot_t1 and overshoot_t2 can

be used.

During the timer overshoot_t1 runs an amplitude defined by set_cw_amplitude bits is

provided to the output driver. Followed by an amplitude denoted by set_residual_carrier

bits with the duration of overshoot_t2.

001aan356

2.50 3.03 3.56 4.10

time ( s)

7.0

5.0

(V)

3.0

1.0

-1.0

Figure 19. Example 1: overshoot_t1 = 2d; overhoot_t2 = 5d.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 34 / 146

001aan357

-1.0 1 2 3 4 5

time ( s)

1.0

3.0

5.0

(V)

7.0

Figure 20. Example 2: overshoot_t1 = 0d; overhoot_t2 = 5d

7.6.2.2 Bit generator

The default coding of a data stream is done by using the Bit-Generator. It is activated

when the value of TxFrameCon.DCodeType is set to 0000 (bin). The Bit-Generator

encodes the data stream byte-wise and can apply the following encoding steps to each

data byte.

1. Add a start-bit of specified type at beginning of every byte

2. Add a stop-bit and EGT bits of a specified type. The maximum number of EGT bit is 6,

only full bits are supported

3. Add a parity-bit of a specified type

4. TxLastBits (skips a given number of bits at the end of the last byte in a frame)

5. Encrypt data-bit (MIFARE Classic encryption)

It is not possible to skip more than 8 bit of a single byte!

By default, data bytes are always treated LSB first.

7.6.3 Receiver circuitry

7.6.3.1 General

The SLRC610 features a versatile quadrature receiver architecture with fully differential

signal input at RXP and RXN. It can be configured to achieve optimum performance for

reception of various 13.56 MHz based protocols.

For all processing units various adjustments can be made to obtain optimum

performance.

7.6.3.2 Block diagram

Figure 21 shows the block diagram of the receiver circuitry. The receiving process

includes several steps. First the quadrature demodulation of the carrier signal of 13.56

MHz is done. Several tuning steps in this circuit are possible.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 35 / 146

001aan358

13.56 MHz

I/O CLOCK

GENERATION

I-clks

Q-clks

clk_27 MHz

TIMING

GENERATION

ADC

DATA

Adc_data_readyclk_27 MHz

mixer mix_out_i_p

2-stage BBA

mix_out_i_n

out_i_p

out_i_n

rx_p

rx_n

rx_p

rx_n

mixer

mix_out_q_p

2-stage BBA

mix_out_q_n

out_q_p

out_q_n

rcv_gain<1:0>

rcv_hpcf<1:0>fully/quasi-differential

fully/quasi-differential

rcv_gain<1:0>

rcv_hpcf<1:0>

rx_p

rx_n

Figure 21. Block diagram of receiver circuitry

The receiver can also be operated in a single ended mode. In this case the

Rcv_RX_single bit has to be set. In the single ended mode, the two receiver pins RXP

and RXN need to be connected together and will provide a single ended signal to the

receiver circuitry.

When using the receiver in a single ended mode the receiver sensitivity is decreased

and the achievable reading distance might be reduced, compared to the fully differential

mode.

Table 25. Configuration for single or differential receiver

Mode rcv_rx_single pins RXP and RXN

Fully differential 0 provide differential signal from

differential antenna by separate rx-

coupling branches

Quasi differential 1 connect RXP and RXN together

and provide single ended signal

from antenna by a single rx-

coupling branch

The quadrature-demodulator uses two different clocks, Q-clock and I-clock, with a

phase shift of 90° between them. Both resulting baseband signals are amplified, filtered,

digitized and forwarded to a correlation circuitry.

The typical application is intended to implement the Fully differential mode and

will deliver maximum reader/writer distance. The Quasi differential mode can be

used together with dedicated antenna topologies that allow a reduction of matching

components at the cost of overall reading performance.

During low power card detection the DC levels at the I- and Q-channel mixer outputs

are evaluated. This requires that mixers are directly connected to the ADC. This can be

configured by setting the bit Rx_ADCmode in register Rcv (38h).

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 36 / 146

7.6.4 Active antenna concept

Two main blocks are implemented in the SLRC610. A digital circuitry, comprising state

machines, coder and decoder logic and an analog circuitry with the modulator and

antenna drivers, receiver and amplification circuitry. For example, the interface between

these two blocks can be configured in the way, that the interfacing signals may be routed

to the pins SIGIN and SIGOUT. The most important use of this topology is the active

antenna concept where the digital and the analog blocks are separated. This opens the

possibility to connect e.g. an additional digital block of another SLRC610 device with a

single analog antenna front-end.

001aam307

SIGIN

SIGINSIGOUT

SIGOUT

READER IC

(DIGITAL)

READER IC

(ANTENNA)

Figure 22. Block diagram of the active Antenna concept

The Table 25 and Table 26 describe the necessary register configuration for the use

case active antenna concept.

Table 26. Register configuration of SLRC610 active antenna concept (DIGITAL)

SigOut.SigOutSel 0100 TxEnvelope

Rcv.SigInSel 11 Receive over SigIn (Generic Code)

DrvCon.TxSel 00 Low (idle)

Table 27. Register configuration of SLRC610 active antenna concept (Antenna)

SigOut.SigOutSel 0110 Generic Code (Manchester)

Rcv.SigInSel 01 Internal

DrvCon.TxSel 10 External (SigIn)

RxCtrl.RxMultiple 1 RxMultiple on

The interface between these two blocks can be configured in the way, that the interfacing

signals may be routed to the pins SIGIN and SIGOUT (see Figure 23 "Overview SIGIN/

SIGOUT Signal Routing").

This topology supports, that some parts of the analog part of the SLRC610 may be

connected to the digital part of another device.

The switch SigOutSel in registerSigOut can be used to measure signals. This is

especially important during the design In phase or for test purposes to check the

transmitted and received data.

However, the most important use of SIGIN/SIGOUT pins is the active antenna concept.

An external active antenna circuit can be connected to the digital circuit of the SLRC610.

SigOutSel has to be configured in that way that the signal of the internal Miller Coder

is sent to SIGOUT pin (SigOutSel = 4). SigInSel has to be configured to receive

Manchester signal with sub-carrier from SIGIN pin (SigInSel = 1).

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 37 / 146

It is possible, to connect a passive antenna to pins TX1, TX2 and RX (via the appropriate

filter and matching circuit) and at the same time an active antenna to the pins SIGOUT

and SIGIN. In this configuration, two RF-parts may be driven (one after another) by a

single host processor.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 38 / 146

001aam001

CODER SIGOUTSel[4:0]

Sigpro_in_sel

[1:0]

SIGOUT

SIGIN

TX bit stream

DIGITAL MODULE ANALOG MODULE

RX bit stream

0, 1

tri-state

LOW

HIGH

TX envelope

TX active

S3C signal

RX envelope

8RX active

RX bit signal

DECODER

SUBCARRIER

DEMODULATOR

TxCon.TxSel

[1:0]

No_nodulation

TX envelope

RFU

SIGIN

tri-state

internal analog block

SIGIN over envelope

SIGIN generic

MODULATOR DRIVER

TX2

TX1

RXN

RXP

DEMODULATOR

Figure 23. Overview SIGIN/SIGOUT Signal Routing

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 39 / 146

7.6.5 Symbol generator

The symbol generator is used to create various protocol symbols like the CS symbol as

used by the ICODE EPC protocol.

Symbols are defined by means of the symbol definition registers and the mode registers.

Four different symbols can be used. Two of them, Symbol0 and Symbol1 have a

maximum pattern length of 16 bit and feature a burst length of up to 256 bits of either

logic "0" or logic "1". The Symbol2 and Symbol3 are limited to 8 bit pattern length and do

not support a burst.

The definition of symbol patterns is done by writing the bit sequence of the pattern to

the appropriate register. The last bit of the pattern to be sent is located at the LSB of

the register. By setting the symbol length in the symbol-length register (TxSym10Len

and TxSym32Len) the definition of the symbol pattern is completed. All other bits at bit-

position higher than the symbol length in the definition register are ignored. (Example:

length of Symbol2 = 5, bit7 and bit6 are ignored, bit5 to bit0 define the symbol pattern,

bit5 is sent first)

Which symbol-pattern is sent can be configured in the TxFrameCon register. Symbol0,

Symbol1 and Symbol2 can be sent before data packets, Symbol1, Symbol2 and Symbol3

can be sent after data packets. Each symbol is defined by a set of registers. Symbols are

configured by a pair of registers. Symbol0 and Symbol1 share the same configuration

and Symbol2 and Symbol3 share the same configuration. The configuration includes

setting of bit-clock- and subcarrier-frequency, as well as selection of the pulse type/length

and the envelope type.

7.7 Memory

7.7.1 Memory overview

The SLRC610 implements three different memories: EEPROM, FIFO and Registers.

At startup, the initialization of the registers which define the behavior of the IC is

performed by an automatic copy of an EEPROM area (read/write EEPROM section1 and

section2, register reset) into the registers. The behavior of the SLRC610 can be changed

by executing the command LoadProtocol, which copies a selected default protocol from

the EEPROM (read only EEPROM section4, register Set Protocol area) into the registers.

The read/write EEPROM section2 can be used to store any user data or predefined

"LoadRegister" into the internal registers.

The FIFO is used as Input/Out buffer and is able to improve the performance of a system

with limited interface speed.

7.7.2 EEPROM memory organization

The SLRC610 has implemented a EEPROM non-volatile memory with a size of 8

kB.The EEPROM is organized in pages of 64 bytes. One page of 64 bytes can be

programmed at a time. Defined purposes had been assigned to specific memory areas

of the EEPROM, which are called Sections. Five sections 0..4 with different purpose do

exist.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 40 / 146

Table 28. EEPROM memory organization

Section Page Byte

addresses

Access

rights

Memory content

00 to 31 r product information and configuration0 0

32 to 63 r/w product configuration

1 1 to 2 64 to 191 r/w register reset

2 3 to 111 192 to 7167 r/w free

3 112 to 128 7168 to 8191 r Register Set Protocol (RSP, TX and RX)

The following figure show the structure of the EEPROM:

aaa-002467

Production and configSection 0:

FreeSection 2:

RSP-Area for TXSection 3_TX:

RSP-Area for RXSection 3_RX:

Figure 24. Sector arrangement of the EEPROM

7.7.2.1 Product information and configuration - Page 0

The first EEPROM page includes production data as well as configuration information.

Table 29. Production area (Page 0)

Address

(Hex.)

0 1 2 3 4 5 6 7

00 ProductID Version Unique Identifier

08 Unique Identifier Manufacturer

Data

10 ManufacturerData

18 ManufacturerData

ProductID: Identifier for this SLRC610 product, only address 01h shall be evaluated for

identifying the Product SLRC6103, address 00h and 02h shall be ignored by software.

Please note, that the silicon versions of SLRC61002 and SLRC61003 can be identified

on register address 7Fh, it is not coded in the EEPROM production area.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 41 / 146

Table 30. Product ID overview of CLRC663 family

Address 01h Product ID

CLRC663 01h

MFRC631 C0h

MFRC630 80h

SLRC610 20h

Version: This register indicates the version of the EEPROM initialization data during

production. (Identification of the Hardware version is available in the register 7Fh, not in

the EEPROM Version address. The hardware information in register 7Fh is hardwired

and therefore independent from any EEPROM configuration.)

Unique Identifier: Unique number code for this device

Manufacturer Data: This data is programmed during production. The content is not

intended to be used by any application and might be not the same for different devices.

Therefore this content needs to be considered to be undefined.

Table 31. Configuration area (Page 0)

Address

(Hex.)

0 1 2 3 4 5 6 7

20 I2C_Address Interface I2C SAM_Address DefaultProtRx DefaultProtTx - TxCRCPreset

28 RxCRCPreset - - - - - -

30 -

38 -

I2C-Address: Two possibilities exist to define the address of the I2C interface. This can

be done either by configuring the pins IF0, IF2 (address is then 10101xx, xx is defined by

the interface pins IF0, IF2) or by writing value into the I2C address area. The selection,

which of this 2-information pin configuration or EEPROM content - is used as I2C-address

is done at EEPROM address 21h (Interface, bit4)

InterfaceThis section describes the interface byte configuration.

Table 32. Interface byte

Bit 7 6 5 4 3 2 1 0

I2C_HSP - - I2C_Address Boundary Scan Host

access rights r/w RFU RFU r/w r/w - - -

Table 33. Interface bits

Bit Symbol Description

7 I2C_HSP when cleared, the high speed mode is used

when set, the high speed+ mode is used (default)

6, 5 RFU -

4 I2C_Address when cleared, the pins are used (default)

when set, the EEPROM is used

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 42 / 146

Bit Symbol Description

3 Boundary

Scan

when cleared, the boundary scan interface is ON (default)

when set, the boundary scan is OFF

2 to 0 Host 000b - RS232

001b - I2C

010b - SPI

011b - I2CL

1xxb - pin selection

I2C_SAM_Address: The I2C SAM Address is always defined by the EEPROM content.

The Register Set Protocol (RSP) Area contains settings for the TX registers (16 bytes)

and for the RX registers (8 bytes).

Table 34. Tx and Rx arrangements in the register set protocol area

Section

Section 4 TX Tx0 Tx1 TX2 Tx3

Section 4 TX Tx4 Tx5 TX6 TX7

Section 4 Rx RX0 RX1 RX2 RX3 RX4 RX5 RX6 RX7

Section 4 Rx RX8 RX9 RX10 RX11 RX12 RX13 RX14 RX15

TxCrcPresetThe data bits are send by the analog module and are automatically

extended by a CRC.

7.7.3 EEPROM initialization content LoadProtocol

The SLRC610 EEPROM is initialized at production with values which are used to reset

certain registers of the SLRC610 to default settings by copying the EEprom content

to the registers. Only registers or bits with "read/write" or "dynamic" access rights are

initialized with this default values copied from the EEProm.

Note that the addresses used for copying reset values from EEprom to registers are

dependent on the configured protocol and can be changed by the user.

Table 35. Register reset values (Hex.) (Page0)

Address 0 (8) 1 (9) 2 (A) 3 (B) 4 (C) 5 (D) 6 (E) 7 (F)

Function Product ID Version Unique Identifier

00 XX see table 30 XX XX XX XX XX XX

Function Unique Identifier Factory trim

value

08 XX XX XX XX XX XX XX XX

Function TrimLFO Factory trim values

10 XX XX XX XX XX XX XX XX

Function Factory trim values

18.... XX XX XX XX XX XX XX XX

Factory trim values

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 43 / 146

Address 0 (8) 1 (9) 2 (A) 3 (B) 4 (C) 5 (D) 6 (E) 7 (F)

....38 XX XX XX XX XX XX XX XX

The register reset values are configuration parameters used after startup of the IC. They

can be changed to modify the default behavior of the device. In addition to this register

reset values, is the possibility to load settings for various user implemented protocols.The

load protocol command is used for this purpose.

Table 36. Register reset values (Hex.)(Page1 and page 2)

Address 0 (8) 1 (9) 2 (A) 3 (B) 4 (C) 5 (D) 6 (E) 7 (F)

Command HostCtrl FiFoControl WaterLevel FiFoLength FiFoData IRQ0 IRQ1

40 40 00 80 05 00 00 00 00

IRQ0En IRQ1En Error Status RxBitCtrl RxColl TControl T0Control

48 10 00 00 00 00 00 00 00

T0ReloadHi T0ReloadLo T0Counter

ValHi

T0Counter

ValLo

T1Control T1ReloadHi T1ReloadLo T1Counter

ValHi

50 00 80 00 00 00 00 80 00

T1Counter

ValLo

T2Control T2ReloadHi T2ReloadLo T2Counter

ValHi

T2Counter

ValLo

T3Control T3ReloadHi

58 00 00 00 80 00 00 00 00

T3ReloadLo T3Counter

ValHi

T3Counter

ValHi

T4Control T4ReloadHi T4ReloadLo T4Counter

ValHi

T4Counter

ValLo

60 80 00 00 00 00 80 00 00

DrvMode TxAmp DrvCon Txl TxCRC

Preset

RxCRC

Preset

TxDataNum TxModWith

68 86 15 11 06 18 18 08 27

TxSym10

BurstLen

TxWaitCtrl TxWaitLo FrameCon RxSofD RxCtrl RxWait RxThres

hold

70 00 C0 12 CF 00 04 90 3F

Rcv RxAna RFU SerialSpeed LFO_trimm PLL_Ctrl PLL_Div LPCD_QMin

78 12 0A 00 7A 80 04 20 48

LPCD_

QMax

LPCD_IMin LPCD

_result_I

LPCD

_result_Q

PadEn PadOut PadIn SigOut

80 12 88 00 00 00 00 00 00

TxBitMod RFU TxDataCon TxDataMod TxSymFreq TxSym0H TySym0L TxSym1H

88 20 xx 04 50 40 00 00 00

TxSym1L TxSym2 TxSym3 TxSym10Le

ngth

TxSym32Le

ngth

TxSym32Bu

rstCtrl

TxSym10M

TxSym32M

90 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x50

RxBitMod RxEOFSym RxSyncValH RxSyncValL RxSyncMod RxMod RXCorr FabCal

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 44 / 146

Address 0 (8) 1 (9) 2 (A) 3 (B) 4 (C) 5 (D) 6 (E) 7 (F)

98 0x02 0x00 0x00 0x01 0x00 0x08 0x08 0xB2

7.8 Clock generation

7.8.1 Crystal oscillator

The clock applied to the SLRC610 acts as time basis for generation of the carrier sent

out at TX and for the quadrature mixer I and Q clock generation as well as for the coder

and decoder of the synchronous system. Therefore stability of the clock frequency is an

important factor for proper performance. To obtain highest performance, clock jitter has

to be as small as possible. This is best achieved by using the internal oscillator buffer

with the recommended circuitry.

001aam308

27.12 MHz

XTAL1 XTAL2

READER IC

Figure 25. Quartz connection

Table 37. Crystal requirements recommendations

Symbol Parameter Conditions Min Typ max Unit

fxtal crystal frequency - 27.12 - MHz

Δfxtal/fxtal relative crystal

frequency variation

-250 - +250 ppm

ESR equivalent series

resistance

- 50 100 Ω

CLload capacitance - 10 - pF

Pxtal crystal power

dissipation

- 50 100 μW

7.8.2 IntegerN PLL clock line

The SLRC610 is able to provide a clock with configurable frequency at CLKOUT from

1 MHz to 24 MHz (PLL_Ctrl and PLL_DIV). There it can serve as a clock source to a

microcontroller which avoids the need of a second crystal oscillator in the reader system.

Clock source for the IntegerN-PLL is the 27.12 MHz crystal oscillator.

Two dividers are determining the output frequency. First a feedback integer-N divider

configures the VCO frequency to be N × fin/2 (control signal pll_set_divfb). As supported

Feedback Divider Ratios are 23, 27 and 28, VCO frequencies can be 23 × fin / 2 (312

MHz), 27 × fin / 2 (366 MHz) and 28 × fin / 2 (380 MHz).

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 45 / 146

The VCO frequency is divided by a factor which is defined by the output divider

(pll_set_divout). Table 37 "Divider values for selected frequencies using the integerN

PLL" shows the accuracy achieved for various frequencies (integer multiples of 1 MHz

and some typical RS232 frequencies) and the divider ratios to be used. The register bit

ClkOutEn enables the clock at CLKOUT pin.

The following formula can be used to calculate the output frequency:

fout = 13.56 MHz × PLLDiv_FB /PLLDiv_Out

Table 38. Divider values for selected frequencies using the integerN PLL

Frequency [MHz] 4 6 8 10 12 20 24 1.8432 3.6864

PLLDiv_FB 23 27 23 28 23 28 23 28 28

PLLDiv_Out 78 61 39 38 26 19 16 206 103

accuracy [%] 0.04 0.03 0.04 0.08 0.04 0.08 0.04 0.01 0.01

7.8.3 Low Frequency Oscillator (LFO)

The SLRC610 family implements an Low-Frequency Oscillator (LFO). Timer T4 can be

configured to use a clock generated by this LFO as input clock, and can be configured

as wakeup counter. As wakeup counter, the timer T4 allows to wake up the system in

regular time intervals which allows to design a reader that is regularly polling for card

presence or implements a low-power card detection (LPCD).

The LFO is trimmed during chip production to run at 16 kHz. Unless a high accuracy

of the LFO is required by the application, and the device is operated in an environment

with changing ambient temperatures, trimming of the LFO is not required. For a typical

application making use of the LFO for wake-up from power saving mode, the trim value

set during production can be used.

Optional trimming to achieve a higher accuracy of the 16 kHz LFO clock is supported by

a digital state machine which compares LFO-clock to a reference clock generated by the

connected 27.12Mhz crystal. As reference clock frequency for trimming of the LFO, a

13.56 MHz clock (27.12Mhz divided by 2 ) input clock to one of the timers T0,T1,T2 or T3

is used.

One of the timers T0,T1,T2,T3 with an input clock of 13,56 MHz crystal clock is used to

count one clock period of the LFO. For an LFO Clock running at 16KHz this would result

in 848 wakeup timer clocks of timer Tx (T0, T1, T2, T3). Therefrore, the timer count value

Tx at the end of a trimming cycle is expected to be 176 (wakeup timer is counting down:

1023-848=175, +/- 1 tolerance is accepted). The trim cycle is executed once in the T4

timer cycle. Therefore the T4 autoload value shall be bigger than 0x05 to ensure that

one trimming cycle takes place before T4 expires. The Tx timer value is reloaded to 1023

during the start of an Auto trim cycle. This happens every time, once after the T4 timer

underflows.

At the end of each trim cycle, the timer value is checked:

•Timer Tx value < 174: LFO Frequency is too low and the trim value is incremented by 1

on T4 Timer event

•Timer Tx value > 176: LFO Frequency is too high and the trim value is decremented by

1 on T4 Timer event

•Timer Tx value is within 174 and 176: LFO Frequency = 16 KHz and trimming

procedure is stopped

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 46 / 146

The cycle proceeds until the autotrimm function is stopped (Timer Tx value is within 174

and 176).

In addition, the trimming cycle can be aborted by sending an IDLE Command from the

host to cancel the current command execution. T3 is not allowed to be used in case

T4AutoLPCD is set in parallel. It is not required to configure a TXStart condition with

underflow. The T0/1/2/3 timer will typically not underflow. It may happen if the LPO clock

is very slow, but it is not required to take an action to generate this event.

7.9 Power management

7.9.1 Supply concept

The SLRC610 is supplied by VDD (Supply Voltage), PVDD (Pad Supply) and TVDD

(Transmitter Power Supply). These three voltages are independent from each other.

To connect the SLRC610 to a Microcontroller supplied by 3.3 V, PVDD and VDD shall be

at a level of 3.3 V, TVDD can be in a range from 3.3 V to 5.0 V. A higher supply voltage

at TVDD will result in a higher field strength.

Independent of the voltage it is recommended to buffer these supplies with blocking

capacitances close to the terminals of the package. VDD and PVDD are recommended to

be blocked with a capacitor of 100 nF min, TVDD is recommended to be blocked with 2

capacitors, 100 nF parallel to 1.0 μF

AVDD and DVDD are not supply input pins. They are output pins and shall be connected

to blocking capacitors 470 nF each.

7.9.2 Power reduction mode

7.9.2.1 Power-down

A hard power-down is enabled with HIGH level on pin PDOWN. This turns off the internal

1.8 V voltage regulators for the analog and digital core supply as well as the oscillator.

All digital input buffers are separated from the input pads and clamped internally (except

pin PDOWN itself). The output pins are switched to high impedance. HardPowerDown is

performing a reset of the IC. All registers will be reset, the Fifo will be cleared.

To leave the power-down mode the level at the pin PDOWN as to be set to LOW. This

will start the internal start-up sequence.

7.9.2.2 Standby mode

The standby mode is entered immediately after setting the bit PowerDown in the register

Command. All internal current sinks are switched off. Voltage references and voltage

regulators will be set into stand-by mode.

In opposition to the power-down mode, the digital input buffers are not separated by the

input pads and keep their functionality. The digital output pins do not change their state.

During standby mode, all registers values, the FIFO’s content and the configuration itself

will keep its current content.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 47 / 146

To leave the standby mode the bit PowerDown in the register Command is cleared. This

will trigger the internal start-up sequence. The reader IC is in full operation mode again

when the internal start-up sequence is finalized (the typical duration is 15 us).

A value of 55h must be sent to the SLRC610 using the RS232 interface to leave the

standby mode. This is must at RS232, but cannot be used for the I2C/SPI interface. Then

read accesses shall be performed at address 00h until the device returns the content of

this address. The return of the content of address 00h indicates that the device is ready

to receive further commands and the internal start-up sequence is finalized.

7.9.2.3 Modem off mode

When the ModemOff bit in the register Control is set the antenna transmitter and the

receiver are switched off.

To leave the modem off mode clears the ModemOff bit in the register Control.

7.9.3 Low-Power Card Detection (LPCD)

The low-power card detection is an energy saving mode in which the SLRC610 is not

fully powered permanently.

The LPCD works in two phases. First the standby phase is controlled by the wake-up

counter (WUC), which defines the duration of the standby of the SLRC610. Second

phase is the detection-phase. In this phase the values of the I and Q channel are

detected and stored in the register map. (LPCD_I_Result, LPCD_Q_Result).This time

period can be handled with Timer3. The value is compared with the min/max values in

the registers (LPCD_IMin, LPCD_IMax; LPCD_QMin, LPCD_QMax). If it exceeds the

limits, a LPCDIRQ is raised.

After the command LPCD the standby of the SLRC610 is activated, if selected.

The wake-up Timer4 can activate the system after a given time. For the LPCD it is

recommended to set T4AutoWakeUp and T4AutoRestart, to start the timer and then go

to standby. If a card is detected the communication can be started. If T4AutoWakeUp is

not set, the IC will not enter Standby mode in case no card is detected.

7.9.4 Reset and start-up time

A 10 μs constant high level at the PDOWN pin starts the internal reset procedure.

The following figure shows the internal voltage regulator:

001aan360

PVDD

PDown

VSS

GLITCH

FILTER

INTERNAL VOLTAGE

REGULATOR

VDD

VSS

1.8 V

AVDD

DVDD

Figure 26. Internal PDown to voltage regulator logic

When the SLRC610 has finished the reset phase and the oscillator has entered a stable

working condition the IC is ready to be used. A typical duration before the IC is ready to

receive commands after the reset had been released is 2.5ms.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 48 / 146

7.10 Command set

7.10.1 General

The behavior is determined by a state machine capable to perform a certain set of

commands. By writing a command-code to the command register the command is

executed.

Arguments and/or data necessary to process a command, are exchanged via the FIFO

buffer.

•Each command that needs a certain number of arguments will start processing only

when it has received the correct number of arguments via the FIFO buffer.

•The FIFO buffer is not cleared automatically at command start. It is recommended to

write the command arguments and/or the data bytes into the FIFO buffer and start the

command afterwards.

•Each command may be stopped by the host by writing a new command code into the

command register e.g.: the Idle-Command.

7.10.2 Command set overview

Table 39. Command set

Command No. Parameter (bytes) Short description

Idle 00h - no action, cancels current command execution

LPCD 01h - low-power card detection

AckReq 04h - performs a query, an Ack and a Req-Rn for ISO/IEC

18000-3 mode 3/ EPC Class-1 HF

Receive 05h - activates the receive circuit

Transmit 06h bytes to send: byte1, byte2,.... transmits data from the FIFO buffer

Transceive 07h bytes to send: byte1, byte2,.... transmits data from the FIFO buffer and automatically

activates the receiver after transmission finished

WriteE2 08h addressH, addressL, data; gets one byte from FIFO buffer and writes it to the

internal EEPROM

WriteE2Page 09h (page Address), data0,

[data1 ..data63];

gets up to 64 bytes (one EEPROM page) from the FIFO

buffer and writes it to the EEPROM

ReadE2 0Ah addressH, address L, length; reads data from the EEPROM and copies it into the

FIFO buffer

LoadReg 0Ch (EEPROM addressH), (EEPROM

addressL), RegAdr, (number of

reads data from the internal EEPROM and initializes

the SLRC610 registers. EEPROM address needs to be

within EEPROM sector 2

LoadProtocol 0Dh (Protocol number RX), (Protocol

number TX);

reads data from the internal EEPROM and initializes the

SLRC610 registers needed for a Protocol change

ReadRNR 1Ch - Copies bytes from the Random Number generator into

the FIFO until the FiFo is full

Soft Reset 1Fh - resets the SLRC610

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 49 / 146

7.10.3 Command functionality

7.10.3.1 Idle command

Command (00h);

This command indicates that the SLRC610 is in idle mode. This command is also used to

terminate the actual command.

7.10.3.2 LPCD command

Command (01h);

This command performs a low-power card detection and/or an automatic trimming of

the LFO. After wakeup from standby, the values of the sampled I and Q channels are

compared with the min/max threshold values in the registers. If it exceeds the limits, an

LPCD_IRQ will be raised. After the LPCD command the standby is activated, if selected.

7.10.3.3 AckReq command

Command (04h);

Performs a Query (Full command must be written into the FIFO); a Ack and a ReqRn

command. All answers to the command will be written into the FIFO. The error flag is

copied after the answer into the FIFO.

This command terminates automatically and the then active state is idle.

7.10.3.4 Receive command

Command (05h);

The SLRC610 activates the receiver path and waits for any data stream to be received,

according to its register settings. The registers must be set before starting this command

according to the used protocol and antenna configuration. The correct settings have to be

chosen before starting the command.

This command terminates automatically when the received data stream ends. This

is indicated either by the end of frame pattern or by the length byte depending on the

selected framing and speed.

7.10.3.5 Transmit command

Command (06h); data to transmit

The content of the FIFO is transmitted immediately after starting the command. Before

transmitting the FIFO all relevant registers have to be set to transmit data.

This command terminates automatically when the FIFO gets empty. It can be terminated

by any other command written to the command register.

7.10.3.6 Transceive command

Command (07h); data to transmit

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 50 / 146

This command transmits data from FIFO buffer and automatically activates the receiver

after a transmission is finished.

Each transmission process starts by writing the command into CommandReg.

Remark: If the bit RxMultiple in register RxModeReg is set to logic 1, this command will

never leave the receiving state, because the receiving will not be cancelled automatically.

7.10.3.7 WriteE2 command

Command (08h), Parameter1 (addressH), Parameter2 (addressL), Parameter3 (data);

This command writes one byte into the EEPROM. If the FIFO contains no data, the

command will wait until the data is available.

Abort condition: Address-parameter outside of allowed range 0x00 – 0x7F.

7.10.3.8 WriteE2PAGE command

Command (09h), Parameter1 (page address), Parameter2..63 (data0, data1...data63);

This command writes up to 64 bytes into the EEPROM. The addresses are not allowed

to wrap over a page border. If this is the case, this additional data be ignored and stays

in the fifo. The programming starts after 64 bytes are read from the FIFO or the FIFO is

empty.

Abort condition: Insufficient parameters in FIFO; Page address parameter outside of

range 0x00 – 0x7F.

7.10.3.9 ReadE2 command

Command (0Ah), Parameter1 (addressH), Parameter2 (addressL), Parameter3 (length);

Reads up to 256 bytes from the EEPROM to the FIFO. If a read operation exceeds the

address 1FFFh, the read operation continues from address 0000h.

Abort condition: Insufficient parameter in FIFO; Address parameter outside of range.

7.10.3.10 LoadReg command

Command (0Ch), Parameter1 (EEPROM addressH),Parameter2 (EEPROM addressL),

Parameter3 (RegAdr), Parameter4 (number);

Read a defined number of bytes from the EEPROM and copies the value into the

Abort condition: Insufficient parameter in FIFO; Address parameter outside of range.

7.10.3.11 LoadProtocol command

Command (0Dh), Parameter1 (Protocol number RX), Parameter2 (Protocol number TX);

Reads out the EEPROM Register Set Protocol Area and overwrites the content of the

Rx- and Tx- related registers. These registers are important for a Protocol selection.

Abort condition: Insufficient parameter in FIFO

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 51 / 146

Table 40. Predefined protocol overview RX[1]

Protocol

Number

(decimal)

Protocol Receiver speed

[kbits/s]

Receiver Coding

00 ISO/IEC15693 26 SSC

01 ISO/IEC15693 52 SSC

02 ISO/IEC15693 26 DSC

03 EPC/UID 26 SSC

04 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

212 2/424

05 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

106 4/424

06 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

424 2/848

07 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

212 4/848

[1] For more protocol details please refer to Section 7 "Functional description".

Table 41. Predefined protocol overview TX[1]

Protocol

Number

(decimal)

Protocol Transmitter speed

[kbits/s]

Transmitter Coding

00 ISO/IEC15693 26 1/4

01 ISO/IEC15693 26 1/4

02 ISO/IEC15693 1,66 1/256

03 EPC/UID 53 Unitray

04 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

based on Tari value,

ASK, PIE

05 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

based on Tari value,

ASK, PIE

06 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

based on Tari value,

ASK, PIE

07 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

based on Tari value,

ASK, PIE

[1] For more protocol details please refer to Section 7 "Functional description".

7.10.3.12 GetRNR command

Command (1Ch);

This command is reading Random Numbers from the random number generator of the

SLRC610. The Random Numbers are copied to the FIFO until the FIFO is full.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 52 / 146

7.10.3.13 SoftReset command

Command (1Fh);

This command is performing a soft reset. Triggered by this command all the default

values for the register setting will be read from the EEPROM and copied into the register

set.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 53 / 146

8 SLRC610 registers

8.1 Register bit behavior

Depending on the functionality of a register, the access conditions to the register can

vary. In principle, bits with same behavior are grouped in common registers. The access

conditions are described in the following table: 5 m

Table 42. Behavior of register bits and their designation

Abbreviation Behavior Description

r/w read and write These bits can be written and read via the host interface. Since

they are used only for control purposes, the content is not

influenced by the state machines but can be read by internal

state machines.

dy dynamic These bits can be written and read via the host interface. They

can also be written automatically by internal state machines, for

example Command register changes its value automatically after

the execution of the command.

r read only These register bits indicate hold values which are determined by

internal states only.

w write only Reading these register bits always returns zero.

RFU - These bits are reserved for future use and must not be changed.

In case of a required write access, it is recommended to write a

logic 0.

Table 43. SLRC610 registers overview

Address Register name Function

00h Command Starts and stops command execution

01h HostCtrl Host control register

02h FIFOControl Control register of the FIFO

03h WaterLevel Level of the FIFO underflow and overflow warning

04h FIFOLength Length of the FIFO

05h FIFOData Data In/Out exchange register of FIFO buffer

06h IRQ0 Interrupt register 0

07h IRQ1 Interrupt register 1

08h IRQ0En Interrupt enable register 0

09h IRQ1En Interrupt enable register 1

0Ah Error Error bits showing the error status of the last command execution

0Bh Status Contains status of the communication

0Ch RxBitCtrl Control register for anticollision adjustments for bit oriented protocols

0Dh RxColl Collision position register

0Eh TControl Control of Timer 0..3

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 54 / 146

Address Register name Function

0Fh T0Control Control of Timer0

10h T0ReloadHi High register of the reload value of Timer0

11h T0ReloadLo Low register of the reload value of Timer0

12h T0CounterValHi Counter value high register of Timer0

13h T0CounterValLo Counter value low register of Timer0

14h T1Control Control of Timer1

15h T1ReloadHi High register of the reload value of Timer1

16h T1ReloadLo Low register of the reload value of Timer1

17h T1CounterValHi Counter value high register of Timer1

18h T1CounterValLo Counter value low register of Timer1

19h T2Control Control of Timer2

1Ah T2ReloadHi High byte of the reload value of Timer2

1Bh T2ReloadLo Low byte of the reload value of Timer2

1Ch T2CounterValHi Counter value high byte of Timer2

1Dh T2CounterValLo Counter value low byte of Timer2

1Eh T3Control Control of Timer3

1Fh T3ReloadHi High byte of the reload value of Timer3

20h T3ReloadLo Low byte of the reload value of Timer3

21h T3CounterValHi Counter value high byte of Timer3

22h T3CounterValLo Counter value low byte of Timer3

23h T4Control Control of Timer4

24h T4ReloadHi High byte of the reload value of Timer4

25h T4ReloadLo Low byte of the reload value of Timer4

26h T4CounterValHi Counter value high byte of Timer4

27h T4CounterValLo Counter value low byte of Timer4

28h DrvMod Driver mode register

29h TxAmp Transmitter amplifier register

2Ah DrvCon Driver configuration register

2Bh Txl Transmitter register

2Ch TxCrcPreset Transmitter CRC control register, preset value

2Dh RxCrcPreset Receiver CRC control register, preset value

2Eh TxDataNum Transmitter data number register

2Fh TxModWidth Transmitter modulation width register

30h TxSym10BurstLen Transmitter symbol 1 + symbol 0 burst length register

31h TXWaitCtrl Transmitter wait control

32h TxWaitLo Transmitter wait low

33h FrameCon Transmitter frame control

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 55 / 146

Address Register name Function

34h RxSofD Receiver start of frame detection

35h RxCtrl Receiver control register

36h RxWait Receiver wait register

37h RxThreshold Receiver threshold register

38h Rcv Receiver register

39h RxAna Receiver analog register

RFU No function implemented for SLRC610023Ah

LPCD_Options For SLRC61003: Options for LPCD configuration

3Bh SerialSpeed Serial speed register

3Ch LFO_Trimm Low-power oscillator trimming register

3Dh PLL_Ctrl IntegerN PLL control register, for microcontroller clock output adjustment

3Eh PLL_DivOut IntegerN PLL control register, for microcontroller clock output adjustment

3Fh LPCD_QMin Low-power card detection Q channel minimum threshold

40h LPCD_QMax Low-power card detection Q channel maximum threshold

41h LPCD_IMin Low-power card detection I channel minimum threshold

42h LPCD_I_Result Low-power card detection I channel result register

43h LPCD_Q_Result Low-power card detection Q channel result register

44h PadEn PIN enable register

45h PadOut PIN out register

46h PadIn PIN in register

47h SigOut Enables and controls the SIGOUT Pin

48h TxBitMod Transmitter bit mode register

49h RFU -

4Ah TxDataCon Transmitter data configuration register

4Bh TxDataMod Transmitter data modulation register

4Ch TxSymFreq Transmitter symbol frequency

4Dh TxSym0H Transmitter symbol 0 high register

4Eh TxSym0L Transmitter symbol 0 low register

4Fh TxSym1H Transmitter symbol 1 high register

50h TxSym1L Transmitter symbol 1 low register

51h TxSym2 Transmitter symbol 2 register

52h TxSym3 Transmitter symbol 3 register

53h TxSym10Len Transmitter symbol 1 + symbol 0 length register

54h TxSym32Len Transmitter symbol 3 + symbol 2 length register

55h TxSym10BurstCtrl Transmitter symbol 1 + symbol 0 burst control register

56h TxSym10Mod Transmitter symbol 1 + symbol 0 modulation register

57h TxSym32Mod Transmitter symbol 3 + symbol 2 modulation register

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 56 / 146

Address Register name Function

58h RxBitMod Receiver bit modulation register

59h RxEofSym Receiver end of frame symbol register

5Ah RxSyncValH Receiver synchronisation value high register

5Bh RxSyncValL Receiver synchronisation value low register

5Ch RxSyncMod Receiver synchronisation mode register

5Dh RxMod Receiver modulation register

5Eh RxCorr Receiver correlation register

5Fh FabCal Calibration register of the receiver, calibration performed at production

48h-5Fh RFU -

7Fh Version Version and subversion register

8.2 Command configuration

8.2.1 Command

Starts and stops command execution.

Table 44. Command register (address 00h)

Bit 7 6 5 4 3 2 1 0

Symbol Standby Modem

Off

RFU Command

Access

rights

dy r/w - dy

Table 45. Command bits

Bit Symbol Description

7 Standby Set to 1, the IC is entering power-down mode.

6 ModemOff Set to logic 1, the receiver and the transmitter circuit is powering down.

5 RFU -

4 to 0 Command Defines the actual command for the SLRC610.

8.3 SAM configuration register

8.3.1 HostCtrl

Via the HostCtrl Register the interface access right can be controlled

Table 46. HostCtrl register (address 01h);

Bit 7 6 5 4 3 2 1 0

Symbol RegEn BusHost BusSAM RFU SAMInterface SAMInterface RFU RFU

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 57 / 146

Bit 7 6 5 4 3 2 1 0

Access

rights

dy r/w r/w - r/w r/w - -

Table 47. HostCtrl bits

Bit Symbol Description

7 RegEn If this bit is set to logic 1, the register HostCtrl_reg can be changed

at the next register access. The next write access clears this bit

automatically.

6 BusHost Set to logic 1, the bus is controlled by the host. This bit cannot be set

together with the bit BusSAM. This bit can only be set if the bit RegEn

is previously set.

5 BusSAM Set to logic 1, the bus is controlled by the SAM. This bit cannot be

set together with BusHost. This bit can only be set if the bit RegEn is

previously set.

4 RFU -

3 to 2 SAMInterface 0h:SAM Interface switched off

1h:SAM Interface SPI active

2h:SAM Interface I2CL active

3h:SAM Interface I2C active

1 to 0 RFU -

8.4 FIFO configuration register

8.4.1 FIFOControl

FIFOControl defines the characteristics of the FIFO

Table 48. FIFOControl register (address 02h);

Bit 7 6 5 4 3 2 1 0

Symbol FIFOSize HiAlert LoAlert FIFOFlush RFU WaterLe

velExtBit

FIFOLengthExtBits

Access

rights

r/w r r w - r/w r

Table 49. FIFOControl bits

Bit Symbol Description

7 FIFOSize Set to logic 1, FIFO size is 255 bytes;

Set to logic 0, FIFO size is 512 bytes.

It is recommended to change the FIFO size only, when the

FIFO content had been cleared.

6 HiAlert Set to logic 1, when the number of bytes stored in the FIFO

buffer fulfils the following equation:

HiAlert = (FIFOSize - FIFOLength) <= WaterLevel

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 58 / 146

Bit Symbol Description

5 LoAlert Set to logic 1, when the number of bytes stored in the FIFO

buffer fulfils the following conditions:

LoAlert =1 if FIFOLength <= WaterLevel

4 FIFOFlush Set to logic 1 clears the FIFO buffer. Reading this bit will always

return 0

3 RFU -

2 WaterLevelExtBit Defines the bit 8 (MSB) for the waterlevel (extension of register

WaterLevel). This bit is only evaluated in the 512-byte FIFO

mode. Bits 7..0 are defined in register WaterLevel.

1 to 0 FIFOLengthExtBits Defines the bit9 (MSB) and bit8 for the FIFO length (extension

of FIFOLength). These two bits are only evaluated in the

512-byte FIFO mode, The bits 7..0 are defined in register

FIFOLength.

8.4.2 WaterLevel

Defines the level for FIFO under- and overflow warning levels.This register is extended

by 1 bit in FIFOControl in case the 512-byte FIFO mode is activated by setting bit

FIFOControl.FIFOSize.

Table 50. WaterLevel register (address 03h);

Bit 76543210

Symbol WaterLevelBits

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 51. WaterLevel bits

Bit Symbol Description

7 to 0 WaterLevelBits Sets a level to indicate a FIFO-buffer state which can be read

from bits HighAlert and LowAlert in the FifoControl. In 512-byte

FIFO mode, the register is extended by bit WaterLevelExtBit in the

FIFOControl. This functionality can be used to avoid a FIFO buffer

overflow or underflow:

The bit HiAlert bit in FIFO Control is read logic 1, if the number of

bytes in the FIFO-buffer is equal or less than the number defined

by the waterlevel configuration.

The bit LoAlert bit in FIFO control is read logic 1, if the number of

bytes in the FIFO buffer is equal or less than the number defined

by the waterlevel configuration.

Note: For the calculation of HiAlert and LoAlert see register

description of these bits (Section 8.4.1 "FIFOControl").

8.4.3 FIFOLength

Number of bytes in the FIFO buffer. In 512-byte mode this register is extended by

FIFOControl.FifoLength.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 59 / 146

Table 52. FIFOLength register (address 04h); reset value: 00h

Bit 76543210

Symbol FIFOLength

Access

rights

Table 53. FIFOLength bits

Bit Symbol Description

7 to 0 FIFOLength Indicates the number of bytes in the FIFO buffer. In 512-byte

mode this register is extended by the bits FIFOLength in the

FIFOControl register. Writing to the FIFOData register increments,

reading decrements the number of available bytes in the FIFO.

8.4.4 FIFOData

In- and output of FIFO buffer. Contrary to any read/write access to other addresses,

reading or writing to the FIFO address does not increment the address pointer. Writing

to the FIFOData register increments, reading decrements the number of bytes present in

the FIFO.

Table 54. FIFOData register (address 05h);

Bit 76543210

Symbol FIFOData

Access

rights

dy dy dy dy dy dy dy dy

Table 55. FIFOData bits

Bit Symbol Description

7 to 0 FIFOData Data input and output port for the internal FIFO buffer. Refer to

Section 7.5 "Buffer".

8.5 Interrupt configuration registers

The Registers IRQ0 register and IRQ1 register implement a special functionality to avoid

the unintended modification of bits.

The mechanism of changing register contents requires the following consideration:

IRQ(x).Set indicates, if a set bit on position 0 to 6 shall be cleared or set. Depending

on the content of IRQ(x).Set, a write of a 1 to positions 0 to 6 either clears or sets the

corresponding bit. With this register the application can modify the interrupt status which

is maintained by the SLRC610.

Bit 7 indicates, if the intended modification is a setting or clearance of a bit. Any 1 written

to a bit position 6...0 will trigger the setting or clearance of this bit as defined by bit 7.

Example: writing FFh sets all bits 6..0, writing 7Fh clears all bits 6..0 of the interrupt

request register

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 60 / 146

8.5.1 IRQ0 register

Interrupt request register 0.

Table 56. IRQ0 register (address 06h); reset value: 00h

Bit 7 6 5 4 3 2 1 0

Symbol Set Hi AlertIRQ Lo

AlertIRQ

IdleIRQ TxIRQ RxIRQ ErrIRQ RxSOF

IRQ

Access

rights

w dy dy dy dy dy dy dy

Table 57. IRQ0 bits

Bit Symbol Description

7 Set 1: writing a 1 to a bit position 6..0 sets the interrupt request

0: Writing a 1 to a bit position 6..0 clears the interrupt request

6 HiAlerIRQ Set, when bit HiAlert in register Status1Reg is set. In opposition to HiAlert,

HiAlertIRQ stores this event.

5 LoAlertIRQ Set, when bit LoAlert in register Status1 is set. In opposition to LoAlert,

LoAlertIRQ stores this event.

4 IdleIRQ Set, when a command terminates by itself e.g. when the Command

changes its value from any command to the Idle command. If an unknown

command is started, the Command changes its content to the idle state and

the bit IdleIRQ is set. Starting the Idle command by the Controller does not

set bit IdleIRQ. .

3 TxIRQ Set, when data transmission is completed, which is immediately after the

last bit is sent.

2 RxIRQ Set, when the receiver detects the end of a data stream.

Note: This flag is no indication that the received data stream is correct. The

error flags have to be evaluated to get the status of the reception.

1 ErrIRQ Set, when the one of the following errors is set:

FifoWrErr, FiFoOvl, ProtErr, NoDataErr, IntegErr.

0 RxSOFlrq Set, when a SOF or a subcarrier is detected.

8.5.2 IRQ1 register

Interrupt request register 1.

Table 58. IRQ1 register (address 07h)

Bit 7 6 5 4 3 2 1 0

Symbol Set GlobalIRQ LPCD_IRQ Timer4IRQ Timer3IRQ Timer2IRQ Timer1IRQ Timer0IRQ

Access

rights

w dy dy dy dy dy dy dy

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 61 / 146

Table 59. IRQ1 bits

Bit Symbol Description

7 Set 1: writing a 1 to a bit position 5..0 sets the interrupt request

0: Writing a 1 to a bit position 5..0 clears the interrupt request

6 GlobalIRQ Set, if an enabled IRQ occurs.

5 LPCD_IRQ Set if a card is detected in Low-power card detection sequence.

4 Timer4IRQ Set to logic 1 when Timer4 has an underflow.

3 Timer3IRQ Set to logic 1 when Timer3 has an underflow.

2 Timer2IRQ Set to logic 1 when Timer2 has an underflow.

1 Timer1IRQ Set to logic 1 when Timer1 has an underflow.

0 Timer0IRQ Set to logic 1 when Timer0 has an underflow.

8.5.3 IRQ0En register

Interrupt request enable register for IRQ0. This register allows to define if an interrupt

request is processed by the SLRC610.

Table 60. IRQ0En register (address 08h)

Bit 7 6 5 4 3 2 1 0

Symbol IRQ_Inv Hi AlertIRQEn LoAlertIRQEn IdleIRQEn TxIRQEn RxIRQEn ErrIRQEn RxSOF

IRQEn

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 61. IRQ0En bits

Bit Symbol Description

7 IRQ_Inv Set to one the signal of the IRQ pin is inverted

6 Hi AlerIRQEn Set to logic 1, it allows the High Alert interrupt Request (indicated by the

bit HiAlertIRQ) to be propagated to the GlobalIRQ

5 Lo AlertIRQEn Set to logic 1, it allows the Low Alert Interrupt Request (indicated by the

bit LoAlertIRQ) to be propagated to the GlobalIRQ

4 IdleIRQEn Set to logic 1, it allows the Idle interrupt request (indicated by the bit

IdleIRQ) to be propagated to the GlobalIRQ

3 TxIRQEn Set to logic 1, it allows the transmitter interrupt request (indicated by the

bit TxtIRQ) to be propagated to the GlobalIRQ

2 RxIRQEn Set to logic 1, it allows the receiver interrupt request (indicated by the bit

RxIRQ) to be propagated to the GlobalIRQ

1 ErrIRQEn Set to logic 1, it allows the Error interrupt request (indicated by the bit

ErrorIRQ) to be propagated to the GlobalIRQ

0 RxSOFIRQEn Set to logic 1, it allows the RxSOF interrupt request (indicated by the bit

RxSOFIRQ) to be propagated to the GlobalIRQ

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 62 / 146

8.5.4 IRQ1En

Interrupt request enable register for IRQ1.

Table 62. IRQ1EN register (address 09h);

Bit 7 6 5 4 3 2 1 0

Symbol IRQPushPull IRQPinEn LPCD_IRQEn Timer4

IRQEn

Timer3

IRQEn

Timer2

IRQEn

Timer1

IRQEn

Timer0

IRQEn

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 63. IRQ1EN bits

Bit Symbol Description

7 IRQPushPull Set to 1 the IRQ-pin acts as PushPull pin, otherwise it acts as

OpenDrain pin

6 IRQPinEN Set to logic 1, it allows the global interrupt request (indicated by the bit

GlobalIRQ) to be propagated to the interrupt pin

5 LPCD_IRQEN Set to logic 1, it allows the LPCDinterrupt request (indicated by the bit

LPCDIRQ) to be propagated to the GlobalIRQ

4 Timer4IRQEn Set to logic 1, it allows the Timer4 interrupt request (indicated by the bit

Timer4IRQ) to be propagated to the GlobalIRQ

3 Timer3IRQEn Set to logic 1, it allows the Timer3 interrupt request (indicated by the bit

Timer3IRQ) to be propagated to the GlobalIRQ

2 Timer2IRQEn Set to logic 1, it allows the Timer2 interrupt request (indicated by the bit

Timer2IRQ) to be propagated to the GlobalIRQ

1 Timer1IRQEn Set to logic 1, it allows the Timer1 interrupt request (indicated by the bit

Timer1IRQ) to be propagated to the GlobalIRQ

0 Timer0IRQEn Set to logic 1, it allows the Timer0 interrupt request (indicated by the bit

Timer0IRQ) to be propagated to the GlobalIRQ

8.6 Contactless interface configuration registers

8.6.1 Error

Error register.

Table 64. Error register (address 0Ah)

Bit 7 6 5 4 3 2 1 0

Symbol EE_Err FiFoWrErr FIFOOvl MinFrameErr NoDataErr CollDet ProtErr IntegErr

Access

rights

dy dy dy dy dy dy dy dy

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 63 / 146

Table 65. Error bits

Bit Symbol Description

7 EE_Err An error appeared during the last EEPROM command. For

details see the descriptions of the EEPROM commands

6 FIFOWrErr Data was written into the FIFO, during a transmission of a possible

CRC, during "RxWait", "Wait for data" or "Receiving" state, or during an

authentication command. The Flag is cleared when a new CL command is

started. If RxMultiple is active, the flag is cleared after the error flags have

been written to the FIFO.

5 FIFOOvl Data is written into the FIFO when it is already full. The data that is already in

the FIFO will remain untouched. All data that is written to the FIFO after this

Flag is set to 1 will be ignored.

4 Min

FrameErr

A valid SOF was received, but afterwards less then 4 bits of data were

received.

Note: Frames with less than 4 bits of data are automatically discarded and

the RxDecoder stays enabled. Furthermore no RxIRQ is set. The same is

valid for less than 3 Bytes if the EMD suppression is activated

Note: MinFrameErr is automatically cleared at the start of a receive or

transceive command. In case of a transceive command, it is cleared at the

start of the receiving phase ("Wait for data" state)

3 NoDataErr Data should be sent, but no data is in FIFO

2 CollDet A collision has occurred. The position of the first collision is shown in the

Note: CollDet is automatically cleared at the start of a receive or transceive

command. In case of a transceive command, it is cleared at the start of the

receiving phase ("Wait for data" state).

Note: If a collision is part of the defined EOF symbol, CollDet is not set to 1.

1 ProtErr A protocol error has occurred. A protocol error can be a wrong stop bit or

SOF or a wrong number of received data bytes. When a protocol error is

detected, data reception is stopped.

Note: ProtErr is automatically cleared at start of a receive or transceive

command. In case of a transceive command, it is cleared at the start of the

receiving phase ("Wait for data" state).

Note: When a protocol error occurs the last received data byte is not written

into the FIFO.

0 IntegErr A data integrity error has been detected. Possible cause can be a wrong

parity or a wrong CRC. In case of a data integrity error the reception is

continued.

Note: IntegErr is automatically cleared at start of a Receive or Transceive

command. In case of a Transceive command, it is cleared at the start of the

receiving phase ("Wait for data" state).

Note: If the NoColl bit is set, also a collision is setting the IntegErr.

8.6.2 Status

Status register.

Table 66. Status register (address 0Bh)

Bit 76543210

Symbol - - - - - ComState

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 64 / 146

Bit 76543210

Access

rights

RFU RFU RFU RFU RFU r

Table 67. Status bits

Bit Symbol Description

7 to 3 - RFU

ComState shows the status of the transmitter and receiver state machine:

000b ... Idle

001b ... TxWait

011b ... Transmitting

101b ... RxWait

110b ... Wait for data

111b ... Receiving

2 to 0 ComState

100b ... not used

8.6.3 RxBitCtrl

Receiver control register.

Table 68. RxBitCtrl register (address 0Ch);

Bit 7 6 5 4 3 2 1 0

Symbol ValuesAfterColl RxAlign NoColl RxLastBits

Access

rights

r/w r/w r/w r/w r/w w w w

Table 69. RxBitCtrl bits

Bit Symbol Description

7 ValuesAfter

Coll

If cleared, every received bit after a collision is replaced by a zero. This

function is needed for ISO/IEC14443 anticollision

6 to 4 RxAlign Used for reception of bit oriented frames: RxAlign defines the bit position

length for the first bit received to be stored. Further received bits are

stored at the following bit positions.

Example:

RxAlign = 0h - the LSB of the received bit is stored at bit 0, the second

received bit is stored at bit position 1.

RxAlign = 1h - the LSB of the received bit is stored at bit 1, the second

received bit is stored at bit position 2.

RxAlign = 7h - the LSB of the received bit is stored at bit 7, the second

received bit is stored in the following byte at position 0.

Note: If RxAlign = 0, data is received byte-oriented, otherwise bit-

oriented.

3 NoColl If this bit is set, a collision will result in an IntegErr

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 65 / 146

Bit Symbol Description

2 to 0 RxLastBits Defines the number of valid bits of the last data byte received in bit-

oriented communications. If zero the whole byte is valid.

Note: These bits are set by the RxDecoder in a bit-oriented

communication at the end of the communication. They are reset at start

of reception.

8.6.4 RxColl

Receiver collision register.

Table 70. RxColl register (address 0Dh);

Bit 7 6 5 4 3 2 1 0

Symbol CollPosValid CollPos

Access

rights

r r

Table 71. RxColl bits

Bit Symbol Description

7 CollPos

Valid

If set to 1, the value of CollPos is valid. Otherwise no collision is detected or

the position of the collision is out of the range of bits CollPos.

6 to 0 CollPos These bits show the bit position of the first detected collision in a received

frame (only data bits are interpreted). CollPos can only be displayed for the

first 8 bytes of a data stream.

Example:

00h indicates a bit collision in the 1st bit

01h indicates a bit collision in the 2nd bit

08h indicates a bit collision in the 9th bit (1st bit of 2nd byte)

3Fh indicates a bit collision in the 64th bit (8th bit of the 8th byte)

These bits shall only be interpreted in ISO/IEC 15693/ICODE SLI read/write

mode if bit CollPosValid is set.

Note: If RxBitCtrl.RxAlign is set to a value different to 0, this value is

included in the CollPos.

Example: RxAlign = 4h, a collision occurs in the 4th received bit (which is

the last bit of that UID byte). The CollPos = 7h in this case.

8.7 Timer configuration registers

8.7.1 TControl

Control register of the timer section.

The TControl implements a special functionality to avoid the not intended modification of

bits.

Bit 3..0 indicates, which bits in the positions 7..4 are intended to be modified.

Example: writing FFh sets all bits 7..4, writing F0h does not change any of the bits 7..4

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 66 / 146

Table 72. TControl register (address 0Eh)

Bit 7 6 5 4 3 2 1 0

Symbol T3Running T2Running T1Running T0Running T3Start

StopNow

T2Start

StopNow

T1Start

StopNow

T0Start

StopNow

Access

rights

dy dy dy dy w w w w

Table 73. TControl bits

Bit Symbol Description

7 T3Running Indicates Timer3 is running.If the bit T3startStopNow is set/reset, this

bit and the timer can be started/stopped

6 T2Running Indicates Timer2 is running. If the bit T2startStopNow is set/reset, this

bit and the timer can be started/stopped

5 T1Running Indicates tTmer1 is running. If the bit T1startStopNow is set/reset, this

bit and the timer can be started/stopped

4 T0Running Indicates Timer0 is running. If the bit T0startStopNow is set/reset, this

bit and the timer can be started/stopped

3 T3StartStop

Now

The bit 7 of TControl T3Running can be modified if set

2 T2StartStop

Now

The bit 6of TControl T2Running can be modified if set

1 T1StartStop

Now

The bit 5of TControl T1Running can be modified if set

0 T0StartStop

Now

The bit 4 of TControl T0Running can be modified if set

8.7.2 T0Control

Control register of the Timer0.

Table 74. T0Control register (address 0Fh);

Bit 7 6 5 4 3 2 1 0

Symbol T0StopRx - T0Start T0AutoRestart - T0Clk

Access

rights

r/w RFU r/w r/w RFU r/w

Table 75. T0Control bits

Bit Symbol Description

7 T0StopRx If set, the timer stops immediately after receiving the first 4 bits. If

cleared the timer does not stop automatically.

Note: If LFO Trimming is selected by T0Start, this bit has no effect.

6 - RFU

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 67 / 146

Bit Symbol Description

5 to 4 T0Start 00b: The timer is not started automatically

01 b: The timer starts automatically at the end of the transmission

10 b: Timer is used for LFO trimming without underflow (Start/Stop on

PosEdge)

11 b: Timer is used for LFO trimming with underflow (Start/Stop on

PosEdge)

3 T0AutoRestart 1: the timer automatically restarts its count-down from

T0ReloadValue, after the counter value has reached the value zero.

0: the timer decrements to zero and stops.

The bit Timer1IRQ is set to logic 1 when the timer underflows.

2 - RFU

1 to 0 T0Clk 00 b: The timer input clock is 13.56 MHz.

01 b: The timer input clock is 211,875 kHz.

10 b: The timer input clock is an underflow of Timer2.

11 b: The timer input clock is an underflow of Timer1.

8.7.2.1 T0ReloadHi

High byte reload value of the Timer0.

Table 76. T0ReloadHi register (address 10h);

Bit 7 6 5 4 3 2 1 0

Symbol T0Reload Hi

Access

rights

r/w

Table 77. T0ReloadHi bits

Bit Symbol Description

7 to 0 T0ReloadHi Defines the high byte of the reload value of the timer. With the start

event the timer loads the value of the registers T0ReloadValHi,

T0ReloadValLo. Changing this register affects the timer only at the

next start event.

8.7.2.2 T0ReloadLo

Low byte reload value of the Timer0.

Table 78. T0ReloadLo register (address 11h);

Bit 7 6 5 4 3 2 1 0

Symbol T0ReloadLo

Access

rights

r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 68 / 146

Table 79. T0ReloadLo bits

Bit Symbol Description

7 to0 T0ReloadLo Defines the low byte of the reload value of the timer. With the

start event the timer loads the value of the T0ReloadValHi,

T0ReloadValLo. Changing this register affects the timer only at the

next start event.

8.7.2.3 T0CounterValHi

High byte of the counter value of Timer0.

Table 80. T0CounterValHi register (address 12h)

Bit 7 6 5 4 3 2 1 0

Symbol T0CounterValHi

Access

rights

Table 81. T0CounterValHi bits

Bit Symbol Description

7to0 T0Counter

ValHi

High byte value of the Timer0.

This value shall not be read out during reception.

8.7.2.4 T0CounterValLo

Low byte of the counter value of Timer0.

Table 82. T0CounterValLo register (address 13h)

Bit 7 6 5 4 3 2 1 0

Symbol T0CounterValLo

Access

rights

Table 83. T0CounterValLo bits

Bit Symbol Description

7 to 0 T0CounterValLo Low byte value of the Timer0.

This value shall not be read out during reception.

8.7.2.5 T1Control

Control register of the Timer1.

Table 84. T1Control register (address 14h);

Bit 7 6 5 4 3 2 1 0

Symbol T1StopRx - T1Start T1AutoRestart - T1Clk

Access

rights

r/w RFU r/w r/w RFU r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 69 / 146

Table 85. T1Control bits

Bit Symbol Description

7 T1StopRx If set, the timer stops after receiving the first 4 bits. If cleared, the

timer is not stopped automatically.

Note: If LFO trimming is selected by T1start, this bit has no effect.

6 - RFU

5 to 4 T1Start 00b: The timer is not started automatically

01 b: The timer starts automatically at the end of the transmission

10 b: Timer is used for LFO trimming without underflow (Start/Stop on

PosEdge)

11 b: Timer is used for LFO trimming with underflow (Start/Stop on

PosEdge)

3 T1AutoRestart Set to logic 1, the timer automatically restarts its countdown from

T1ReloadValue, after the counter value has reached the value zero.

Set to logic 0 the timer decrements to zero and stops.

The bit Timer1IRQ is set to logic 1 when the timer underflows.

2 - RFU

1 to 0 T1Clk 00 b: The timer input clock is 13.56 MHz

01 b: The timer input clock is 211,875 kHz.

10 b: The timer input clock is an underflow of Timer0

11 b: The timer input clock is an underflow of Timer2

8.7.2.6 T1ReloadHi

High byte (MSB) reload value of the Timer1.

Table 86. T0ReloadHi register (address 15h)

Bit 7 6 5 4 3 2 1 0

Symbol T1ReloadHi

Access

rights

r/w

Table 87. T1ReloadHi bits

Bit Symbol Description

7 to 0 T1ReloadHi Defines the high byte reload value of the Timer 1. With the start event

the timer loads the value of the T1ReloadValHi and T1ReloadValLo.

Changing this register affects the Timer only at the next start event.

8.7.2.7 T1ReloadLo

Low byte (LSB) reload value of the Timer1.

Table 88. T1ReloadLo register (address 16h)

Bit 7 6 5 4 3 2 1 0

Symbol T1ReloadLo

Access

rights

r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 70 / 146

Table 89. T1ReloadValLo bits

Bit Symbol Description

7 to 0 T1ReloadLo Defines the low byte of the reload value of the Timer1. Changing this

8.7.2.8 T1CounterValHi

High byte (MSB) of the counter value of byte Timer1.

Table 90. T1CounterValHi register (address 17h)

Bit 7 6 5 4 3 2 1 0

Symbol T1CounterValHi

Access

rights

Table 91. T1CounterValHi bits

Bit Symbol Description

7 to 0 T1Counter

ValHi

High byte of the current value of the Timer1.

This value shall not be read out during reception.

8.7.2.9 T1CounterValLo

Low byte (LSB) of the counter value of byte Timer1.

Table 92. T1CounterValLo register (address 18h)

Bit 7 6 5 4 3 2 1 0

Symbol T1CounterValLo

Access

rights

Table 93. T1CounterValLo bits

Bit Symbol Description

7 to 0 T1Counter

ValLo

Low byte of the current value of the counter 1.

This value shall not be read out during reception.

8.7.2.10 T2Control

Control register of the Timer2.

Table 94. T2Control register (address 19h)

Bit 7 6 5 4 3 2 1 0

Symbol T2StopRx - T2Start T2AutoRestart - T2Clk

Access

rights

r/w RFU r/w r/w RFU r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 71 / 146

Table 95. T2Control bits

Bit Symbol Description

7 T2StopRx If set the timer stops immediately after receiving the first 4 bits. If

cleared indicates, that the timer is not stopped automatically.

Note: If LFO Trimming is selected by T2Start, this bit has no effect.

6 - RFU

5 to 4 T2Start 00 b: The timer is not started automatically.

01 b: The timer starts automatically at the end of the transmission.

10 b: Timer is used for LFO trimming without underflow (Start/Stop on

PosEdge).

11 b: Timer is used for LFO trimming with underflow (Start/Stop on

PosEdge).

3 T2AutoRestart Set to logic 1, the timer automatically restarts its countdown from

T2ReloadValue, after the counter value has reached the value

zero. Set to logic 0 the timer decrements to zero and stops. The bit

Timer2IRQ is set to logic 1 when the timer underflows

2 - RFU

1 to 0 T2Clk 00 b: The timer input clock is 13.56 MHz.

01 b: The timer input clock is 212 kHz.

10 b: The timer input clock is an underflow of Timer0

11b: The timer input clock is an underflow of Timer1

8.7.2.11 T2ReloadHi

High byte of the reload value of Timer2.

Table 96. T2ReloadHi register (address 1Ah)

Bit 7 6 5 4 3 2 1 0

Symbol T2ReloadHi

Access

rights

r/w

Table 97. T2Reload bits

Bit Symbol Description

7 to 0 T2ReloadHi Defines the high byte of the reload value of the Timer2. With the

start event the timer load the value of the T2ReloadValHi and

T2ReloadValLo. Changing this register affects the timer only at the

next start event.

8.7.2.12 T2ReloadLo

Low byte of the reload value of Timer2.

Table 98. T2ReloadLo register (address 1Bh)

Bit 7 6 5 4 3 2 1 0

Symbol T2ReloadLo

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 72 / 146

Bit 7 6 5 4 3 2 1 0

Access

rights

r/w

Table 99. T2ReloadLo bits

Bit Symbol Description

7 to 0 T2ReloadLo Defines the low byte of the reload value of the Timer2. With the

start event the timer load the value of the T2ReloadValHi and

T2RelaodVaLo. Changing this register affects the timer only at the

next start event.

8.7.2.13 T2CounterValHi

High byte of the counter register of Timer2.

Table 100. T2CounterValHi register (address 1Ch)

Bit 7 6 5 4 3 2 1 0

Symbol T2CounterValHi

Access

rights

Table 101. T2CounterValHi bits

Bit Symbol Description

7 to 0 T2Counter

ValHi

High byte current counter value of Timer2.

This value shall not be read out during reception.

8.7.2.14 T2CounterValLoReg

Low byte of the current value of Timer 2.

Table 102. T2CounterValLo register (address 1Dh)

Bit 7 6 5 4 3 2 1 0

Symbol T2CounterValLo

Access

rights

Table 103. T2CounterValLo bits

Bit Symbol Description

7 to 0 T2Counter

ValLo

Low byte of the current counter value of Timer1Timer2.

This value shall not be read out during reception.

8.7.2.15 T3Control

Control register of the Timer 3.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 73 / 146

Table 104. T3Control register (address 1Eh)

Bit 7 6 5 4 3 2 1 0

Symbol T3StopRx - T3Start T3AutoRestart - T3Clk

Access

rights

r/w RFU r/w r/w RFU r/w

Table 105. T3Control bits

Bit Symbol Description

7 T3StopRx If set, the timer stops immediately after receiving the first 4 bits. If

cleared, indicates that the timer is not stopped automatically.

Note: If LFO Trimming is selected by T3Start, this bit has no effect.

6 - RFU

5 to 4 T3Start 00b - timer is not started automatically

01 b - timer starts automatically at the end of the transmission

10 b - timer is used for LFO trimming without underflow (Start/Stop on

PosEdge)

11 b - timer is used for LFO trimming with underflow (Start/Stop on

PosEdge).

3 T3AutoRestart Set to logic 1, the timer automatically restarts its countdown from

T3ReloadValue, after the counter value has reached the value zero.

Set to logic 0 the timer decrements to zero and stops.

The bit Timer1IRQ is set to logic 1 when the timer underflows.

2 - RFU

1 to 0 T3Clk 00 b - the timer input clock is 13.56 MHz.

01 b - the timer input clock is 211,875 kHz.

10 b - the timer input clock is an underflow of Timer0

11 b - the timer input clock is an underflow of Timer1

8.7.2.16 T3ReloadHi

High byte of the reload value of Timer3.

Table 106. T3ReloadHi register (address 1Fh);

Bit 7 6 5 4 3 2 1 0

Symbol T3ReloadHi

Access

rights

r/w

Table 107. T3ReloadHi bits

Bit Symbol Description

7 to 0 T3ReloadHi Defines the high byte of the reload value of the Timer3. With the

start event the timer load the value of the T3ReloadValHi and

T3ReloadValLo. Changing this register affects the timer only at the

next start event.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 74 / 146

8.7.2.17 T3ReloadLo

Low byte of the reload value of Timer3.

Table 108. T3ReloadLo register (address 20h)

Bit 7 6 5 4 3 2 1 0

Symbol T3ReloadLo

Access

rights

r/w

Table 109. T3ReloadLo bits

Bit Symbol Description

7 to 0 T3ReloadLo Defines the low byte of the reload value of Timer3. With the

start event the timer load the value of the T3ReloadValHi and

T3RelaodValLo. Changing this register affects the timer only at the

next start event.

8.7.2.18 T3CounterValHi

High byte of the current counter value the 16-bit Timer3.

Table 110. T3CounterValHi register (address 21h)

Bit 7 6 5 4 3 2 1 0

Symbol T3CounterValHi

Access

rights

Table 111. T3CounterValHi bits

Bit Symbol Description

7 to 0 T3Counter

ValHi

High byte of the current counter value of Timer3.

This value shall not be read out during reception.

8.7.2.19 T3CounterValLo

Low byte of the current counter value the 16-bit Timer3.

Table 112. T3CounterValLo register (address 22h)

Bit 7 6 5 4 3 2 1 0

Symbol T3CounterValLo

Access

rights

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 75 / 146

Table 113. T3CounterValLo bits

Bit Symbol Description

7 to 0 T3Counter

ValLo

Low byte current counter value of Timer3.

This value shall not be read out during reception.

8.7.2.20 T4Control

The wake-up timer T4 activates the system after a given time. If enabled, it can start the

low power card detection function.

Table 114. T4Control register (address 23h)

Bit 7 6 5 4 3 2 1 0

Symbol T4Running T4Start

StopNow

T4Auto

Trimm

T4Auto

LPCD

T4Auto

Restart

T4AutoWakeUp T4Clk

Access

rights

dy w r/w r/w r/w r/w r/w

Table 115. T4Control bits

Bit Symbol Description

7 T4Running Shows if the timer T4 is running. If the bit T4StartStopNow is set,

this bit and the timer T4 can be started/stopped.

6 T4Start

StopNow

if set, the bit T4Running can be changed.

5 T4AutoTrimm If set to one, the timer activates an LFO trimming procedure when it

underflows. For the T4AutoTrimm function, at least one timer (T0 to

T3) has to be configured properly for trimming (T3 is not allowed if

T4AutoLPCD is set in parallel).

4 T4AutoLPCD If set to one, the timer activates a low-power card detection

sequence. If a card is detected an interrupt request is raised and

the system remains active if enabled. If no card is detected the

SLRC610 enters the Power down mode if enabled. The timer is

automatically restarted (no gap). Timer 3 is used to specify the time

where the RF field is enabled to check if a card is present. Therefor

you may not use Timer 3 for T4AutoTrimm in parallel.

3 T4AutoRestart Set to logic 1, the timer automatically restarts its countdown from

T4ReloadValue, after the counter value has reached the value

zero. Set to logic 0 the timer decrements to zero and stops. The bit

Timer4IRQ is set to logic 1 at timer underflow.

2 T4AutoWakeUp If set, the SLRC610 wakes up automatically, when the timer T4 has

an underflow. This bit has to be set if the IC should enter the Power

down mode after T4AutoTrimm and/or T4AutoLPCD is finished and

no card has been detected. If the IC should stay active after one of

these procedures this bit has to be set to 0.

1 to 0 T4Clk 00b - the timer input clock is the LFO clock

01b - the timer input clock is the LFO clock/8

10b - the timer input clock is the LFO clock/16

11b - the timer input clock is the LFO clock/32

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 76 / 146

8.7.2.21 T4ReloadHi

High byte of the reload value of the 16-bit timer 4.

Table 116. T4ReloadHi register (address 24h)

Bit 7 6 5 4 3 2 1 0

Symbol T4ReloadHi

Access

rights

r/w

Table 117. T4ReloadHi bits

Bit Symbol Description

7 to 0 T4ReloadHi Defines high byte of the for the reload value of timer 4. With the start

event the timer 4 loads the T4ReloadVal. Changing this register

affects the timer only at the next start event.

8.7.2.22 T4ReloadLo

Low byte of the reload value of the 16-bit timer 4.

Table 118. T4ReloadLo register (address 25h)

Bit 7 6 5 4 3 2 1 0

Symbol T4ReloadLo

Access

rights

r/w

Table 119. T4ReloadLo bits

Bit Symbol Description

7 to 0 T4ReloadLo Defines the low byte of the reload value of the timer 4. With the start

event the timer loads the value of the T4ReloadVal. Changing this

8.7.2.23 T4CounterValHi

High byte of the counter value of the 16-bit timer 4.

Table 120. T4CounterValHi register (address 26h)

Bit 7 6 5 4 3 2 1 0

Symbol T4CounterValHi

Access

rights

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 77 / 146

Table 121. T4CounterValHi bits

Bit Symbol Description

7 to 0 T4CounterValHi High byte of the current counter value of timer 4.

8.7.2.24 T4CounterValLo

Low byte of the counter value of the 16-bit timer 4.

Table 122. T4CounterValLo register (address 27h)

Bit 7 6 5 4 3 2 1 0

Symbol T4CounterValLo

Access

rights

Table 123. T4CounterValLo bits

Bit Symbol Description

7 to 0 T4CounterValLo Low byte of the current counter value of the timer 4.

8.8 Transmitter configuration registers

8.8.1 TxMode

Table 124. DrvMode register (address 28h)

Bit 7 6 5 4 3 2 1 0

Symbol Tx2Inv Tx1Inv - - TxEn TxClk Mode

Access

rights

r/w r/w RFU RFU r/w r/w

Table 125. DrvMode bits

Bit Symbol Description

7 Tx2Inv Inverts transmitter 2 at TX2 pin

6 Tx1Inv Inverts transmitter 1 at TX1 pin

5 RFU

4 - RFU

3 TxEn If set to 1 both transmitter pins are enabled

2 to 0 TxClkMode Transmitter clock settings (see 8.6.2. Table 27). Codes 011b and

0b110 are not supported. This register defines, if the output is

operated in open drain, push-pull, at high impedance or pulled to a fix

high or low level.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 78 / 146

8.8.2 TxAmp

With the set_cw_amplitude register output power can be traded off against power supply

rejection. Spending more headroom leads to better power supply rejection ration and

better accuracy of the modulation degree.

With CwMax set, the voltage of TX1 will be pulled to the maximum possible. This register

overrides the settings made by set_cw_amplitude.

Table 126. TxAmp register (address 29h)

Bit 7 6 5 4 3 2 1 0

Symbol set_cw_amplitude - set_residual_carrier

Access

rights

r/w RFU r/w

Table 127. TxAmp bits

Bit Symbol Description

7 to 6 set_cw_amplitude Allows to reduce the output amplitude of the transmitter by a

fix value.

Four different preset values that are subtracted from TVDD

can be selected:

0: TVDD -100 mV

1: TVDD -250 mV

2: TVDD -500 mV

3: TVDD -1000 mV

5 RFU -

4 to 0 set_residual_ carrier Set the residual carrier percentage. refer to Section 7.6.2

8.8.3 TxCon

Table 128. TxCon register (address 2Ah)

Bit 7 6 5 4 3 2 1 0

Symbol OvershootT2 CwMax TxInv TxSel

Access

rights

r/w r/w r/w r/w

Table 129. TxCon bits

Bit Symbol Description

7 to 4 OvershootT2 Specifies the length (number of carrier clocks) of the additional

modulation for overshoot prevention. Refer to Section 7.6.2.1

"Overshoot protection"

3 Cwmax Set amplitude of continuous wave carrier to the maximum.

If set, set_cw_amplitude in Register TxAmp has no influence on the

continuous amplitude.

2 TxInv If set, the resulting modulation signal defined by TxSel is inverted

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 79 / 146

Bit Symbol Description

1 to 0 TxSel Defines which signal is used as source for modulation

00b ... no modulation

01b ... TxEnvelope

10b ... SigIn

11b ... RFU

8.8.4 Txl

Table 130. Txl register (address 2Bh)

Bit 7 6 5 4 3 2 1 0

Symbol OvershootT1 tx_set_iLoad

Access

rights

r/w r/w

Table 131. Txl bits

Bit Symbol Description

7 to 4 OvershootT1 Overshoot value for Timer1. Refer to Section 7.6.2.1 "Overshoot

protection"

3 to 0 tx_set_iLoad Factory trim value, sets the expected Tx load current. This value is

used to control the modulation index in an optimized way dependent

on the expected TX load current.

8.9 CRC configuration registers

8.9.1 TxCrcPreset

Table 132. TXCrcPreset register (address 2Ch)

Bit 7 6 5 4 3 2 1 0

Symbol RFU TXPresetVal TxCRCtype TxCRCInvert TxCRCEn

Access

rights

- r/w r/w r/w r/w

Table 133. TxCrcPreset bits

Bit Symbol Description

7 RFU -

6 to 4 TXPresetVal Specifies the CRC preset value for transmission (see Table 133).

3 to 2 TxCRCtype Defines which type of CRC (CRC8/CRC16/CRC5) is calculated:

•00h -- CRC5

•01h -- CRC8

•02h -- CRC16

•03h -- RFU

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 80 / 146

Bit Symbol Description

1 TxCRCInvert if set, the resulting CRC is inverted and attached to the data frame

(ISO/IEC 3309)

0 TxCRCEn if set, a CRC is appended to the data stream

Table 134. Transmitter CRC preset value configuration

TXPresetVal[6...4] CRC16 CRC8 CRC5

0h 0000h 00h 00h

1h 6363h 12h 12h

2h A671h BFh -

3h FFFEh FDh -

4h - - -

5h - - -

6h User defined User defined User defined

7h FFFFh FFh 1Fh

Remark: User defined CRC preset values can be configured by EEprom (see Section

7.7.2.1, Table 30 "Configuration area (Page 0)").

8.9.2 RxCrcCon

Table 135. RxCrcCon register (address 2Dh)

Bit 7 6 5 4 3 2 1 0

Symbol RxForceCRCWrite RXPresetVal RXCRCtype RxCRCInvert RxCRCEn

Access

rights

r/w r/w r/w r/w r/w

Table 136. RxCrcCon bits

Bit Symbol Description

7 RxForceCrc

Write

If set, the received CRC byte(s) are copied to the FIFO.

If cleared CRC Bytes are only checked, but not copied to the FIFO.

This bit has to be always set in case of a not byte aligned CRC (e.g.

ISO/IEC 18000-3 mode 3/ EPC Class-1HF)

6 to 4 RXPresetVal Defines the CRC preset value (Hex.) for transmission. (see Table

136).

3 to 2 RxCRCtype Defines which type of CRC (CRC8/CRC16/CRC5) is calculated:

•00h -- CRC5

•01h -- CRC8

•02h -- CRC16

•03h -- RFU

1 RxCrcInvert If set, the CRC check is done for the inverted CRC.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 81 / 146

Bit Symbol Description

0 RxCrcEn If set, the CRC is checked and in case of a wrong CRC an error flag is

set. Otherwise the CRC is calculated but the error flag is not modified.

Table 137. Receiver CRC preset value configuration

RXPresetVal[6...4] CRC16 CRC8 CRC5

0h 0000h 00h 00h

1h 6363h 12h 12h

2h A671h BFh -

3h FFFEh FDh -

4h - - -

5h - - -

6h User defined User defined User defined

7h FFFFh FFh 1Fh

8.10 Transmitter configuration registers

8.10.1 TxDataNum

Table 138. TxDataNum register (address 2Eh)

Bit 7 6 5 4 3 2 1 0

Symbol RFU RFU- RFU- KeepBitGrid DataEn TxLastBits

Access

rights

r/w r/w r/w

Table 139. TxDataNum bits

Bit Symbol Description

7 to 5 RFU -

4 KeepBitGrid If set, the time between consecutive transmissions starts is a multiple

of one ETU. If cleared, consecutive transmissions can even start

within one ETU

3 DataEn If cleared - it is possible to send a single symbol pattern.

If set - data is sent.

2 to 0 TxLastBits Defines how many bits of the last data byte to be sent. If set to 000b

all bits of the last data byte are sent.

Note - bits are skipped at the end of the byte.

Example - Data byte B2h (sent LSB first).

TxLastBits = 011b (3h) => 010b (LSB first) is sent

TxLastBits = 110b (6h) => 010011b (LSB first) is sent

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 82 / 146

8.10.2 TxSym10BurstLen

If a protocol requires a burst (an unmodulated subcarrier) the length can be defined with

this TxSymBurstLen, the value high or low can be defined by TxSym10BurstCtrl.

Table 140. TxSym10BurstLen register (address 30h)

Bit 7 6 5 4 3 2 1 0

Symbol RFU Sym1Burst Len RFU RFU

Access

rights

- r/w - -

Table 141. TxSym10BurstLen bits

Bit Symbol Description

7 RFU -

6 to 4 Sym1BurstLen Specifies the number of bits issued for symbol 1 burst. The 3 bits

encodes a range from 8 to 256 bit:

00h - 8bit

01h - 16bit

02h - 32bit

04h - 48bit

05h - 64bit

06h - 96bit

07h - 128bit

08h - 256bit

3 to 0 RFU -

8.10.3 TxWaitCtrl

Table 142. TxWaitCtrl register (address 31h); reset value: C0h

Bit 7 6 5 4 3 2 1 0

Symbol TxWaitStart TxWaitEtu TxWait High RFU

Access

rights

r/w r/w r/w -

Table 143. TXWaitCtrl bits

Bit Symbol Description

7 TxWaitStart If cleared, the TxWait time is starting at the End of the send data

(TX).

If set, the TxWait time is starting at the End of the received data

(RX).

6 TxWaitEtu If cleared, the TxWait time is TxWait × 16/13.56 MHz.

If set, the TxWait time is TxWait × 0.5 / DBFreq (DBFreq is the

frequency of the bit stream as defined by TxDataCon).

5 to 3 TxWait High Bit extension of TxWaitLo. TxWaitCtrl bit 5 is MSB.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 83 / 146

Bit Symbol Description

2 to 0 TxStopBitLength Defines stop-bits and EGT (= stop-bit + extra guard time EGT) to

be send:

0h: no stop-bit, no EGT

1h: 1 stop-bit, no EGT

2h: 1 stop-bit + 1 EGT

3h: 1 stop-bit + 2 EGT

4h: 1 stop-bit + 3 EGT

5h: 1 stop-bit + 4 EGT

6h: 1 stop-bit + 5 EGT

7h: 1 stop-bit + 6 EGT

Note: This is only valid for ISO/IEC14443 Type B

8.10.4 TxWaitLo

Table 144. TxWaitLo register (address 32h)

Bit 7 6 5 4 3 2 1 0

Symbol TxWaitLo

Access

rights

r/w

Table 145. TxWaitLo bits

Bit Symbol Description

7 to 0 TxWaitLo Defines the minimum time between receive and send or between two

send data streams

Note: TxWait is a 11bit register (additional 3 bits are in the TxWaitCtrl

See also TxWaitEtu and TxWaitStart.

8.11 FrameCon

Table 146. FrameCon register (address 33h)

Bit 7 6 5 4 3 2 1 0

Symbol TxParityEn RxParityEn - - StopSym StartSym

Access

rights

r/w r/w RFU RFU r/w r/w

Table 147. FrameCon bits

Bit Symbol Description

7 TxParityEn If set, a parity bit is calculated and appended to each byte

transmitted.

6 RxParityEn If set, the parity calculation is enabled. The parity is not transferred to

the FIFO.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 84 / 146

Bit Symbol Description

5 to 4 - RFU

3 to 2 StopSym Defines which symbol is sent as stop-symbol:

•0h: No symbol is sent

•1h: Symbol0 is sent

•2 h symbol1 is sent

•3h Symbol2 is sent

1 to 0 StartSym Defines which symbol is sent as start-symbol:

•0h: No Symbol is sent

•1h: Symbol0 is sent

•2 h: Symbol1 is sent

•3h: Symbol2 is sent

8.12 Receiver configuration registers

8.12.1 RxSofD

Table 148. RxSofD register (address 34h)

Bit 7 6 5 4 3 2 1 0

Symbol RFU SOF_En SOFDetected RFU SubC_En SubC_Detected SubC_Present

Access

rights

- r/w dy - r/w dy r

Table 149. RxSofD bits

Bit Symbol Description

7 to 6 RFU -

5 SOF_En If set and a SOF is detected an RxSOFIRQ is raised.

4 SOF_Detected Shows that a SOF is or was detected. Can be cleared by SW.

3 RFU -

2 SubC_En If set and a subcarrier is detected an RxSOFIRQ is raised.

1 SubC_Detected Shows that a subcarrier is or was detected. Can be cleared by SW.

0 SubC_Present Shows that a subcarrier is currently detected.

8.12.2 RxCtrl

Table 150. RxCtrl register (address 35h)

Bit 7 6 5 4 3 2 1 0

Symbol RxAllowBits RxMultiple RFU RFU EMD_Sup Baudrate

Access

rights

r/w r/w - - r/w r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 85 / 146

Table 151. RxCtrl bits

Bit Symbol Description

7 RxAllowBits If set, data is written into FIFO even if CRC is enabled, and no

complete byte has been received.

6 RxMultiple If set, RxMultiple is activated and the receiver will not terminate

automatically (refer Section 7.10.3.4 "Receive command").

If set to logic 1, at the end of a received data stream an error byte is

added to the FIFO. The error byte is a copy of the Error register.

5 to 4 RFU -

3 EMD_Sup Enables the EMD suppression according ISO/IEC14443. If an error

occurs within the first three bytes, these three bytes are assumed to

be EMD, ignored and the FIFO is reset. A collision is treated as an

error as well If a valid SOF was received, the EMD_Sup is set and a

frame of less than 3 bytes had been received. RX_IRQ is not set in

this EMD error cases. If RxForceCRCWrite is set, the FIFO should not

be read out before three bytes are written into.

2 to 0 Baudrate Defines the baud rate of the receiving signal.

2h: 26 kBd

3h: 52 kBd

all remaining values are RFU

8.12.3 RxWait

Selects internal receiver settings.

Table 152. RxWait register (address 36h)

Bit 76543210

Symbol RxWaitEtu RxWait

Access

rights

r/w r/w

Table 153. RxWait bits

Bit Symbol Description

7 RXWaitEtu If set to 0, the RxWait time is RxWait × 16/13.56 MHz.

If set to 1, the RxWait time is RxWait × (0.5/DBFreq).

6 to 0 RxWait Defines the time after sending, where every input is ignored.

8.12.4 RxThreshold

Selects minimum threshold level for the bit decoder.

Table 154. RxThreshold register (address 37h)

Bit 76543210

Symbol MinLevel MinLevelP

Access

rights

r/w r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 86 / 146

Table 155. RxThreshold bits

Bit Symbol Description

7 to 4 MinLevel Defines the MinLevel of the reception.

Note: The MinLevel should be higher than the noise level in the system.

3 to 0 MinLevelP Defines the MinLevel of the phase shift detector unit.

8.12.5 Rcv

Table 156. Rcv register (address 38h)

Bit 7 6 5 4 3 2 1 0

Symbol Rcv_Rx_single Rx_ADCmode SigInSel RFU CollLevel

Access

rights

r/w r/w r/w - r/w

Table 157. Rcv bits

Bit Symbol Description

7 Rcv_Rx_single Single RXP Input Pin Mode;

0: Fully Differential

1: Quasi-Differential

6 Rx_ADCmode Defines the operation mode of the Analog Digital Converter (ADC)

0: normal reception mode for ADC

1: LPCD mode for ADC

5 to 4 SigInSel Defines input for the signal processing unit:

0h - idle

1h - internal analog block (RX)

2h - signal in over envelope (ISO/IEC14443A)

3h - signal in over s3c-generic

3 to 2 RFU -

1 to 0 CollLevel Defines the strength of a signal to be interpreted as a collision:

0h - Collision has at least 1/8 of signal strength

1h - Collision has at least 1/4 of signal strength

2h - Collision has at least 1/2 of signal strength

3h - Collision detection is switched off

8.12.6 RxAna

This register allows to set the gain (rcv_gain) and high pass corner frequencies

(rcv_hpcf).

Table 158. RxAna register (address 39h)

Bit 7 6 5 4 3 2 1 0

Symbol VMid_r_sel RFU rcv_hpcf rcv_gain

Access

rights

r/w - r/w r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 87 / 146

Table 159. RxAna bits

Bit Symbol Description

7, 6 VMid_r_sel Factory trim value, needs to be 0.

5, 4 RFU

3, 2 rcv_hpcf The rcv_hpcf [1:0] signals allow 4 different settings of the base band

amplifier high pass cut-off frequency from ~40 kHz to ~300 kHz.

1 to 0 rcv_gain With rcv_gain[1:0] four different gain settings from 30 dB and 60

dB can be configured (differential output voltage/differential input

voltage).

Table 160. Effect of gain and highpass corner register settings

rcv_gain

(Hex.)

rcv_hpcf

(Hex.)

fl (kHz) fU (MHz) gain (dB20) bandwith

(MHz)

03 00 38 2,3 60 2,3

03 01 79 2,4 59 2,3

03 02 150 2,6 58 2,5

03 03 264 2,9 55 2,6

02 00 41 2,3 51 2,3

02 01 83 2,4 50 2,3

02 02 157 2,6 49 2,4

02 03 272 3,0 41 2,7

01 00 42 2,6 43 2,6

01 01 84 2,7 42 2,6

01 02 157 2,9 41 2,7

01 03 273 3,3 39 3,0

00 00 43 2,6 35 2,6

00 01 85 2,7 34 2,6

00 02 159 2,9 33 2,7

00 03 276 3,4 30 3,1

8.13 Clock configuration

8.13.1 SerialSpeed

This register allows to set speed of the RS232 interface. The default speed is set to

9,6kbit/s. The transmission speed of the interface can be changed by modifying the

entries for BR_T0 and BR_T1. The transfer speed can be calculated by using the

following formulas:

BR_T0 = 0: transfer speed = 27.12 MHz / (BR_T1 + 1)

BR_T0 > 0: transfer speed = 27.12 MHz / (BR_T1 + 33) / 2^(BR_T0 - 1)

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 88 / 146

The framing is implemented with 1 startbit, 8 databits and 1 stop bit. A parity bit is not

used. Transfer speeds above 1228,8 kbit/s are not supported.

Table 161. SerialSpeed register (address3Bh); reset value: 7Ah

Bit 7 6 5 4 3 2 1 0

Symbol BR_T0 BR_T1

Access

rights

r/w r/w

Table 162. SerialSpeed bits

Bit Symbol Description

7 to 5 BR_T0 BR_T0 = 0: transfer speed = 27.12 MHz / (BR_T1 + 1)

BR_T0 > 0: transfer speed = 27.12 MHz / (BR_T1 + 33) / 2^(BR_T0 - 1)

4 to 0 BR_T1 BR_T0 = 0: transfer speed = 27.12 MHz / (BR_T1 + 1)

BR_T0 > 0: transfer speed = 27.12 MHz / (BR_T1 + 33) / 2^(BR_T0 - 1)

Table 163. RS232 speed settings

Transfer speed (kbit/s) SerialSpeed register content (Hex.)

7,2 FA

9,6 EB

14,4 DA

19,2 CB

38,4 AB

57,6 9A

115,2 7A

128,0 74

230,4 5A

460,8 3A

921,6 1C

1228,8 15

8.13.2 LFO_Trimm

Table 164. LFO_Trim register (address 3Ch)

Bit 7 6 5 4 3 2 1 0

Symbol LFO_trimm

Access

rights

r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 89 / 146

Table 165. LFO_Trim bits

Bit Symbol Description

7 to 0 LFO_trimm Trimm value. Refer to Section 7.8.3

Note: If the trimm value is increased, the frequency of the oscillator

decreases.

8.13.3 PLL_Ctrl Register

The PLL_Ctrl register implements the control register for the IntegerN PLL. Two stages

exist to create the ClkOut signal from the 27,12MHz input. In the first stage the 27,12Mhz

input signal is multiplied by the value defined in PLLDiv_FB and divided by two, and the

second stage divides this frequency by the value defined by PLLDIV_Out.

Table 166. PLL_Ctrl register (address3Dh)

Bit 7 6 5 4 3 2 1 0

Symbol ClkOutSel ClkOut_En PLL_PD PLLDiv_FB

Access

rights

r/w r/w r/w r/w

Table 167. PLL_Ctrl register bits

Bit Symbol Description

7 to 4 CLkOutSel •0h - pin CLKOUT is used as I/O

•1h - pin CLKOUT shows the output of the analog PLL

•2h - pin CLKOUT is hold on 0

•3h - pin CLKOUT is hold on 1

•4h - pin CLKOUT shows 27.12 MHz from the crystal

•5h - pin CLKOUT shows 13.56 MHz derived from the crystal

•6h - pin CLKOUT shows 6.78 MHz derived from the crystal

•7h - pin CLKOUT shows 3.39 MHz derived from the crystal

•8h - pin CLKOUT is toggled by the Timer0 overflow

•9h - pin CLKOUT is toggled by the Timer1 overflow

•Ah - pin CLKOUT is toggled by the Timer2 overflow

•Bh - pin CLKOUT is toggled by the Timer3 overflow

•Ch...Fh - RFU

3 ClkOut_En Enables the clock at Pin CLKOUT

2 PLL_PD PLL power down

1-0 PLLDiv_FB PLL feedback divider (see table 174)

Table 168. Setting of feedback divider PLLDiv_FB [1:0]

Bit 1 Bit 0 Division

0 0 23 (VCO frequency 312Mhz)

0 1 27 (VCO frequency 366MHz)

1 0 28 (VCO frequency 380Mhz)

1 1 23 (VCO frequency 312Mhz)

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 90 / 146

8.13.4 PLLDiv_Out

Table 169. PLLDiv_Out register (address 3Eh)

Bit 7 6 5 4 3 2 1 0

Symbol PLLDiv_Out

Access

rights

r/w

Table 170. PLLDiv_Out bits

Bit Symbol Description

7 to 0 PLLDiv_Out PLL output divider factor; Refer to Section 7.8.2

Table 171. Setting for the output divider ratio PLLDiv_Out [7:0]

Value Division

0 RFU

1 RFU

2 RFU

3 RFU

4 RFU

5 RFU

6 RFU

7 RFU

8 8

9 9

10 10

... ...

253 253

254 254

8.14 Low-power card detection configuration registers

The LPCD registers contain the settings for the low-power card detection. The setting

for LPCD_IMax (6 bits) is done by the two highest bits (bit 7, bit 6) of the registers

LPCD_QMin, LPCD_QMax and LPCD_IMin each.

8.14.1 LPCD_QMin

Table 172. LPCD_QMin register (address 3Fh)

Bit 7 6 5 4 3 2 1 0

Symbol LPCD_IMax.5 LPCD_IMax.4 LPCD_QMin

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 91 / 146

Bit 7 6 5 4 3 2 1 0

Access

rights

r/w r/w r/w

Table 173. LPCD_QMin bits

Bit Symbol Description

7, 6 LPCD_IMax Defines the highest two bits of the higher border for the LPCD. If the

measurement value of the I channel is higher than LPCD_IMax, a

LPCD interrupt request is indicated by bit IRQ0.LPCDIRQ.

5 to 0 LPCD_QMin Defines the lower border for the LPCD. If the measurement value of

the Q channel is higher than LPCD_QMin, a LPCDinterrupt request is

indicated by bit IRQ0.LPCDIRQ.

8.14.2 LPCD_QMax

Table 174. LPCD_QMax register (address 40h)

Bit 7 6 5 4 3 2 1 0

Symbol LPCD_IMax.3 LPCD_IMax.2 LPCD_QMax

Access

rights

r/w r/w r/w

Table 175. LPCD_QMax bits

Bit Symbol Description

7 LPCD_IMax.3 Defines the bit 3 of the high border for the LPCD. If the

measurement value of the I channel is higher than LPCD IMax, a

LPCD IRQ is raised.

6 LPCD_IMax.2 Defines the bit 2 of the high border for the LPCD. If the

measurement value of the I channel is higher than LPCD IMax, a

LPCD IRQ is raised.

5 to 0 LPCD_QMax Defines the high border for the LPCD. If the measurement value of

the Q channel is higher than LPCD QMax, a LPCD IRQ is raised.

8.14.3 LPCD_IMin

Table 176. LPCD_IMin register (address 41h)

Bit 7 6 5 4 3 2 1 0

Symbol LPCD_IMax.1 LPCD_IMax.0 LPCD_IMin

Access

rights

r/w r/w r/w

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 92 / 146

Table 177. LPCD_IMin bits

Bit Symbol Description

7 to 6 LPCD_IMax Defines lowest two bits of the higher border for the low-power card

detection (LPCD). If the measurement value of the I channel is higher

than LPCD IMax, a LPCD IRQ is raised.

5 to 0 LPCD_IMin Defines the lower border for the ow power card detection. If the

measurement value of the I channel is lower than LPCD IMin, a LPCD

IRQ is raised.

8.14.4 LPCD_Result_I

Table 178. LPCD_Result_I register (address 42h)

Bit 7 6 5 4 3 2 1 0

Symbol RFU- RFU- LPCD_Result_I

Access

rights

- - r

Table 179. LPCD_I_Result bits

Bit Symbol Description

7 to 6 RFU -

5 to 0 LPCD_Result_I Shows the result of the last low-power card detection (I-Channel).

8.14.5 LPCD_Result_Q

Table 180. LPCD_Result_Q register (address 43h)

Bit 7 6 5 4 3 2 1 0

Symbol RFU LPCD_I

RQ_Clr

LPCD_Reslult_Q

Access

rights

r/w r

Table 181. LPCD_Q_Result bits

Bit Symbol Description

7 RFU -

6 LPCD_IRQ_Clr If set no LPCD IRQ is raised any more until the next low-power

card detection procedure. Can be used by software to clear the

interrupt source.

5 to 0 LPCD_Result_Q Shows the result of the last ow power card detection (Q-Channel).

8.14.6 LPCD_Options

This register is available on the SLRC61003 only. For silicon version SLRC61002 this

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 93 / 146

Table 182. LPCD_Options register (address 3Ah)

Bit 7 6 5 4 3 2 1 0

Symbol LPCD_TX_HIGH LPCD_FILTER LPCD_Q_

UNSTABLE

LPCD_I_UNSTABLE

Access

rights

RFU

r/w r/w r r

Table 183. LPCD_Options

Bit Symbol Description

7 to 4 RFU -

3 LPCD_TX_HIGH If set, the TX-driver will be the same as VTVDD during LPCD. This will allow for

a better LPCD detection range (higher transmitter output voltage) at the cost of

a higher current consumption. If this bit is cleared, the output voltage at the TX

drivers will be = TVDD- 0.4V. If this bit is set, the output voltage at the TX drivers

will be = VTVDD.

2 LPCD_FILTER If set, The LPCD decision is based on the result of a filter which allows

to remove noise from the evaluated signal in I and Q channel. Enabling

LPCD_FILTER allows compensating for noisy conditions at the cost of a longer

RF-ON time required for sampling. The total maximum LPCD sampling time is

4.72us.

1 LPCD_Q_UNSTABLE If bit 2 of this register is set, bit 1 indicates that the Q-channel ADC value was

changing during the LPCD measuring time. Note: Only valid if LPCD_FILTER

(bit 2) = 1. This information can be used by the host application for configuration

of e.g. the threshold LPCD_QMax or inverting the TX drivers.

0 LPCD_I_UNSTABLE If bit 2 of this register is set, bit 0 Indicates that the I-channel ADC value was

changing during the LPCD measuring time. Note: Only valid if LPCD_FILTER

(bit2) = 1. This information can be used by the host application for configuration

of e.g. the threshold LPCD_IMax or inverting the TX drivers.

8.15 Pin configuration

8.15.1 PinEn

Table 184. PinEn register (address 44h)

Bit 7 6 5 4 3 2 1 0

Symbol SIGIN_EN CLKOUT_EN IFSEL1_EN IFSEL0_EN TCK_EN TMS_EN TDI_EN TMDO_EN

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 185. PinEn bits

Bit Symbol Description

7 SIGIN_EN Enables the output functionality on SIGIN (pin 5). The pin is then used

as I/O.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 94 / 146

Bit Symbol Description

6 CLKOUT_EN Enables the output functionality of the CLKOUT (pin 22). The pin is

then used as I/O. The CLKOUT function is switched off.

5 IFSEL1_EN Enables the output functionality of the IFSEL1 (pin 27). The pin is then

used as I/O.

4 IFSEL0_EN Enables the output functionality of the IFSEL0 (pin 26). The pin is then

used as I/O.

3 TCK_EN Enables the output functionality of the TCK (pin 4) of the boundary

scan interface. The pin is then used as I/O. If the boundary scan is

activated in EEPROM, this bit has no function.

2 TMS_EN Enables the output functionality of the TMS (pin 2) of the boundary

scan interface. The pin is then used as I/O. If the boundary scan is

activated in EEPROM, this bit has no function.

1 TDI_EN Enables the output functionality of the TDI (pin 1) of the boundary

scan interface. The pin is then used as I/O. If the boundary scan is

activated in EEPROM, this bit has no function.

0 TDO_EN Enables the output functionality of the TDO(pin 3) of the boundary

scan interface. The pin is then used as I/O. If the boundary scan is

activated in EEPROM, this bit has no function.

8.15.2 PinOut

Table 186. PinOut register (address 45h)

Bit 7 6 5 4 3 2 1 0

Symbol SIGIN_OUT CLKOUT_OUT IFSEL1_OUT IFSEL0_OUT TCK_OUT TMS_OUT TDI_OUT TDO_OUT

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 187. PinOut bits

Bit Symbol Description

7 SIGIN_OUT Output buffer of the SIGIN pin

6 CLKOUT_OUT Output buffer of the CLKOUT pin

5 IFSEL1_OUT Output buffer of the IFSEL1 pin

4 IFSEL0_OUT Output buffer of the IFSEL0 pin

3 TCK_OUT Output buffer of the TCK pin

2 TMS_OUT Output buffer of the TMS pin

1 TDI_OUT Output buffer of the TDI pin

0 TDO_OUT Output buffer of the TDO pin

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 95 / 146

8.15.3 PinIn

Table 188. PinIn register (address 46h)

Bit 7 6 5 4 3 2 1 0

Symbol SIGIN_IN CLKOUT_IN IFSEL1_IN IFSEL0_IN TCK_IN TMS_IN TDI_IN TDO_IN

Access

rights

r r r r r r r r

Table 189. PinIn bits

Bit Symbol Description

7 SIGIN_IN Input buffer of the SIGIN pin

6 CLKOUT_IN Input buffer of the CLKOUT pin

5 IFSEL1_IN Input buffer of the IFSEL1 pin

4 IFSEL0_IN Input buffer of the IFSEL0 pin

3 TCK_IN Input buffer of the TCK pin

2 TMS_IN Input buffer of the TMS pin

1 TDI_IN Input buffer of the TDI pin

0 TDO_IN Input buffer of the TDO pin

8.15.4 SigOut

Table 190. SigOut register (address 47h)

Bit 7 6 5 4 3 2 1 0

Symbol Pad

Speed

RFU SigOutSel

Access

rights

r/w - r/w

Table 191. SigOut bits

Bit Symbol Description

7 PadSpeed If set, the I/O pins are supporting a fast switching mode.The fast mode

for the I/O’s will increase the peak current consumption of the device,

especially if multiple I/Os are switching at the same time. The power

supply needs to be designed to deliver this peak currents.

6 to 4 RFU -

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 96 / 146

Bit Symbol Description

3 to 0 SIGOutSel 0h, 1h - The pin SIGOUT is 3-state

2h - The pin SIGOUT is 0

3h - The pin SIGOUT is 1

4h - The pin SIGOUT shows the TX-envelope

5h - The pin SIGOUT shows the TX-active signal

6h - The pin SIGOUT shows the S3C (generic) signal

7h - The pin SIGOUT shows the RX-envelope

(only valid for ISO/IEC 14443A, 106 kBd)

8h - The pin SIGOUT shows the RX-active signal

9h - The pin SIGOUT shows the RX-bit signal

8.16 Version register

8.16.1 Version

Table 192. Version register (address 7Fh)

Bit 7 6 5 4 3 2 1 0

Symbol Version SubVersion

Access

rights

r r

Table 193. Version bits

Bit Symbol Description

7 to 4 Version Includes the version of the SLRC610 silicon.

SLRC61002: 0x1

SLRC61003: 0x1

3 to 0 SubVersion Includes the subversion of the SLRC610 silicon:

CLRC66302: 0x8

CLRC66303: 0xA

LPCD_OPTIONS register had been added compared to the earlier

version SLRC61002. Default configuration for LoadProtocol updated

for improved performance. User EEPROM initialized with data.

Transmitter driver allows higher ITVDD than lower SubVersions.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 97 / 146

9 Limiting values

Table 194. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VDD supply voltage -0.5 + 6.0 V

VDD(PVDD) PVDD supply voltage -0.5 + 6.0 V

VDD(TVDD) TVDD supply voltage -0.5 + 6.0 V

SLRC61002 - 250IDD(TVDD) TVDD supply current

SLRC61003 -

500

Vi(RXP) input voltage on pin RXP -0.5 + 2.0 V

Vi(RXN) input voltage on pin RXN -0.5 + 2.0 V

Ptot total power dissipation per package - 1125 mW

VESD(HBM) electrostatic discharge voltage Human Body Model (HBM);

1500 Ω, 100 pF; JESD22-A114-

-2000 2000 V

VESD(CDM) electrostatic discharge voltage Charge Device Model (CDM); -500 500 V

Tj(max) maximum junction

temperature

- 125 °C

Tstg storage temperature no supply voltage applied -55 +150 °C

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 98 / 146

10 Recommended operating conditions

Exposure of the device to other conditions than specified in the Recommended Operating

Conditions section for extended periods may affect device reliability.

Electrical parameters (minimum, typical and maximum) of the device are guaranteed only

when it is used within the recommended operating conditions.

Table 195. Operating conditions SLRC61002HN

Symbol Parameter Conditions Min Typ Max Unit

VDD supply voltage 3.0 5.0 5.5 V

VDD(TVDD) TVDD supply voltage [1] 3.0 5.0 5.5 V

VDD(PVDD) PVDD supply voltage 3.0 5.0 5.5 V

Tamb operating ambient

temperature

in still air with exposed pin soldered on a 4

layer JEDEC PCB

-25 +25 +85 °C

Tstg storage temperature no supply voltage applied, relative humidity

45...75%

-40 +25 +125 °C

[1] VDD(PVDD) must always be the same or lower than VDD.

Table 196. Operating conditions SLRC61003HN

Symbol Parameter Conditions Min Typ Max Unit

VDD supply voltage 2.5 5.0 5.5 V

VDD(TVDD) TVDD supply voltage [1] 2.5 5.0 5.5 V

all host interfaces except I2C interface 2.5 5.0 5.5 VVDD(PVDD) PVDD supply voltage

all host interfaces incl. I2C interface 3.0 5.0 5.5 V

Tamb operating ambient

temperature

in still air with exposed pin soldered on a 4

layer JEDEC PCB

-40 +25 +105 °C

Tstg storage temperature no supply voltage applied, relative humidity

45...75%

-45 +25 +125 °C

[1] VDD(PVDD) must always be the same or lower than VDD.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 99 / 146

11 Thermal characteristics

Table 197. Thermal characteristics

Symbol Parameter Conditions Package Typ Unit

Rth(j-a) thermal resistance from junction to

ambient

in still air with exposed pin soldered on a 4

layer JEDEC PCB

HVQFN32 40 K/W

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 100 / 146

12 Characteristics

Table 198. Characteristics

Symbol Parameter Conditions Min Typ Max Unit

Current consumption

IDD = AVDD+DVDD; modem

on (transmitter and

receiver are switched on)

- 17 20 mAIDD supply current

IDD = AVDD+DVDD; modem

off (transmitter and

receiver are switched off)

- 0.45 0.5 mA

IDD(PVDD) PVDD supply current no load on digital pins,

leakage current only

- 0.5 5 μA

SLRC61002HN - 100 250 mAIDD(TVDD) TVDD supply current

SLRC61003HN - 250 350 mA

All OUTx pins floating

ambient temp = +25 °C - 40 400 nA

ambient temp = -40°C...

+85°C

- 1.5 2.1 μA

Ipd power-down current

SLRC61003: ambient temp

= +105 °C

- 3.5 5.2 μA

Istby standby current All OUTx pins floating

ambient temp = 25 °C,

IVDD+ITVDD+ IPVDD

- 3 6

ambient temp = -40°C...

+105°C, Istby = IVDD+ITVDD+

IPVDD

- 5.25 26

μA

All OUTx pins floatingILPCD(sleep) LPCD sleep current

LFO active, no RF field on,

ambient temp = 25 °C

[1] - 3.3 6.3 μA

All OUTx pins floating,

TxLoad = 50 ohms.

LPCD_FILTER = 0; Rfon

duration = 10 us, RF-off

duration 300ms; VTVDD =

3.0V; Tamb = 25°C; ILPCD =

IVDD+ITVDD+ IPVDD

LPCD_TX_HIGH = 0, - 12 -

ILPCD(average)

LPCD average current

LPCD_TX_HIGH = 1 - 23 -

μA

tRFON RF-on time during LPCD LPCD_TX_HIGH = 0;

TVDD=5.0 V

T=25C;

- 10 - μs

LPCD_TX_HIGH = 1;

TVDD=5.0 V; T=25C

- 50 - μs

Buffer capacitors on AVDD,DVDD

CLexternal buffer capacitor AVDD 220 470 - nF

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 101 / 146

Symbol Parameter Conditions Min Typ Max Unit

CLexternal buffer capacitor DVDD 220 470 - nF

I/O pin characteristics SIGIN/OUT7, SIGOUT, CLKOUT/OUT6,

IFSEL0/OUT4, IFSEL1/OUT5, TCK/OUT3, TMS/OUT2, TDI/

OUT1, TDO/OUT0, IRQ, IF0, IF1, IF2, SCL2, SDA2

ILI input leakage current output disabled 0.0 50 500 nA

VIL low-level input voltage -0.5 - 0.3 x VDD(PVDD) V

VIH high-level input voltage 0.7 x

VDD(PVDD)

VDD(PVDD) + 0.5 V

VOL low-level output voltage 0.0 0.0 0.4 V

VOH high-level output voltage If pins are used as output

OUTx, IOH = 4 mA driving

current for each pin

VDD(PVDD)-0.4 VDD(PVDD)

VDD(PVDD) V

Ciinput capacitance 0.0 2.5 4.5 pF

Pin characteristics PDOWN

VIL low-level input voltage 0.0 0.0 0.4 V

VIH high-level input voltage 0.6 x VPVDD VDD(PVDD)

VDD(PVDD) V

Pull-up resistance for TCK, TMS, TDI, IF2

Rpu pull-up resistance 50 72 120 KΩ

Pin characteristics AUX 1, AUX 2

Vooutput voltage 0.0 - 1.8 V

CLload capacitance 0.0 - 400 pF

Pin characteristics RXP, RXN

Vpp input voltage 0 1.65 1.8 V

Ciinput capacitance 2 3.5 5 pF

Vmod(pp) modulation voltage Vmod(pp) = Vi(pp)(max) - Vi(pp)

(min)

- 2.5 - mV

Pins TX1 and TX2

Vooutput voltage Vss(TVSS) - VDD(TVDD) V

SLRC61002 T=25°C,

VDD(TVDD) = 5.0V

- 1.5 - ΩRooutput resistance

SLRC61003: T=25°C,

VDD(TVDD) = 5.0V

- 1.2 - Ω

Clock frequency Pin CLKOUT

fclk clock frequency configured to 27.12 MHz - 27.12 - MHz

δclk clock duty cycle - 50 - %

Crystal connection XTAL1, XTAL2

Vo(p-p) peak-to-peak output

voltage

pin XTAL1 - 1.0 - V

Viinput voltage pin XTAL1 0.0 - 1.8 V

Ciinput capacitance pin XTAL1 - 3 - pF

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 102 / 146

Symbol Parameter Conditions Min Typ Max Unit

Crystal requirements

fxtal crystal frequency ISO/IEC14443 compliancy 27.12-14kHz 27.12 27.12+14kHz MHz

ESR equivalent series

resistance

- 50 100 Ω

CLload capacitance - 10 - pF

Pxtal crystal power dissipation - 50 100 μW

Input characteristics I/O Pin Characteristics IF3-SDA in I2C configuration

ILI input leakage current output disabled - 2 100 nA

VIL LOW-level input voltage -0.5 - +0.3 VDD(PVDD) V

VIH HIGH-level input voltage 0.7 VDD(PVDD) - VDD(PVDD) + 0.5 V

VOL LOW-level output voltage IOL = 3 mA - - 0.3 V

VOL = 0.4 V; Standard

mode, Fast mode

4 - - mAIOL LOW-level output current

VOL = 0.6 V; Standard

mode, Fast mode

6 - - mA

Standard mode, Fast

mode, CL < 400 pF

- - 250 nstf(o) output fall time

Fast mode +; CL < 550 pF - - 120 ns

tSP pulse width of spikes that

must be suppressed by

the input filter

0 - 50 ns

Ciinput capacitance - 3.5 5 pF

Standard mode - - 400 pFCLload capacitance

Fast mode - - 550 pF

tEER EEPROM data retention

time

Tamb = +55 °C 10 - - year

NEEC EEPROM endurance

(number of programming

cycles)

under all operating

conditions

5 x 105- - cycle

[1] Ipd is the total current for all supplies.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 103 / 146

001aak012

VMID

0 V

Vmod

Vi(p-p)(max) Vi(p-p)(min)

13.56 MHz

carrier

Figure 27. Pin RX input voltage

12.1 Timing characteristics

Table 199. SPI timing characteristics

Symbol Parameter Conditions Min Typ Max Unit

tSCKL SCK LOW time 50 - - ns

tSCKH SCK HIGH time 50 - - ns

th(SCKH-D) SCK HIGH to data input

hold time

SCK to changing MOSI 25 - - ns

tsu(D-SCKH) data input to SCK HIGH set-

up time

changing MOSI to SCK 25 - - ns

th(SCKL-Q) SCK LOW to data output

hold time

SCK to changing MISO - - 25 ns

t(SCKL-NSSH) SCK LOW to NSS HIGH

time

0 - - ns

tNSSH NSS HIGH time before communication 50 - - ns

Remark: To send more bytes in one data stream the NSS signal must be LOW during

the send process. To send more than one data stream the NSS signal must be HIGH

between each data stream.

Table 200. I2C-bus timing in fast mode and fast mode plus

Fast mode Fast mode

Plus

Symbol Parameter Conditions

Min Max Min Max

Unit

fSCL SCL clock frequency 0 400 0 1000 kHz

tHD;STA hold time (repeated) START

condition

after this period,

the first clock

pulse is generated

600 - 260 - ns

tSU;STA set-up time for a repeated

START condition

600 - 260 - ns

tSU;STO set-up time for STOP condition 600 - 260 - ns

tLOW LOW period of the SCL clock 1300 - 500 - ns

tHIGH HIGH period of the SCL clock 600 - 260 - ns

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 104 / 146

Fast mode Fast mode

Plus

Symbol Parameter Conditions

Min Max Min Max

Unit

tHD;DAT data hold time 0 900 - 450 ns

tSU;DAT data set-up time 100 - - - ns

trrise time SCL signal 20 300 - 120 ns

tffall time SCL signal 20 300 - 120 ns

trrise time SDA and SCL

signals

20 300 - 120 ns

tffall time SDA and SCL

signals

20 300 - 120 ns

tBUF bus free time between a STOP

and START condition

1.3 - 0.5 - μs

001aaj635

SDA

SCL

tLOW tf

tSP tr

tHD;STA tHD;DAT

tHD;STA

trtHIGH

tSU;DAT

S Sr P S

tSU;STA

tSU;STO

tBUF

Figure 28. Timing for fast and standard mode devices on the I2C-bus

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 105 / 146

13 Application information

A typical application diagram using a complementary antenna connection to the

SLRC610 is shown in Figure 29.

The antenna tuning and RF part matching is described in the application note [1] and [2].

001aam269

VDD PVDD

MICRO-

PROCESSOR

host

interface

TVDD

XTAL1 XTAL2

RXN

VMID

TX1

TVSS

TX2

8 25 18

VSS

33 20

28-31

PDOWN

IRQ

DVDD

AVDD

12 RXP

READER IC

L0 C1 Ra

CRXN

CRXP

Cvmid

27.12 MHz

antenna

Lant

Figure 29. Typical application antenna circuit diagram

13.1 Antenna design description

The matching circuit for the antenna consists of an EMC low pass filter (L0 and C0), a

matching circuitry (C1 and C2), and a receiving circuits (R1 = R3, R2 = R4, C3 = C5

and C4 = C6;), and the antenna itself. The receiving circuit component values needs

to be designed for operation with the SLRC610. A reuse of dedicated antenna designs

done for other products without adaptation of component values will result in degraded

performance.

13.1.1 EMC low pass filter

The MIFARE product-based system operates at a frequency of 13.56 MHz. This

frequency is derived from a quartz oscillator to clock the SLRC610 and is also the

basis for driving the antenna with the 13.56 MHz energy carrier. This will not only

cause emitted power at 13.56 MHz but will also emit power at higher harmonics. The

international EMC regulations define the amplitude of the emitted power in a broad

frequency range. Thus, an appropriate filtering of the output signal is necessary to fulfil

these regulations.

Remark: The PCB layout has a major influence on the overall performance of the filter.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 106 / 146

13.1.2 Antenna matching

Due to the impedance transformation of the given low pass filter, the antenna coil has to

be matched to a certain impedance. The matching elements C1 and C2 can be estimated

and have to be fine tuned depending on the design of the antenna coil.

The correct impedance matching is important to provide the optimum performance.

The overall quality factor has to be considered to guarantee a proper ISO/IEC 14443

communication scheme. Environmental influences have to be considered as well as

common EMC design rules.

For details refer to the NXP application notes.

13.1.3 Receiving circuit

The internal receiving concept of the SLRC610 makes use both side-bands of the sub-

carrier load modulation of the card response via a differential receiving concept (RXP,

RXN). No external filtering is required.

It is recommended to use the internally generated VMID potential as the input potential

of pin RX. This DC voltage level of VMID has to be coupled to the Rx-pins via R2 and

R4. To provide a stable DC reference voltage capacitances C4, C6 has to be connected

between VMID and ground. Refer to Figure 29

Considering the (AC) voltage limits at the Rx-pins the AC voltage divider of R1 + C3 and

R2 as well as R3 + C5 and R4 has to be designed. Depending on the antenna coil design

and the impedance matching the voltage at the antenna coil varies from antenna design

to antenna design. Therefore the recommended way to design the receiving circuit is to

use the given values for R1(= R3), R2 (= R4), and C3 (= C5) from the above mentioned

application note, and adjust the voltage at the RX-pins by varying R1(= R3) within the

given limits.

Remark: R2 and R4 are AC-wise connected to ground (via C4 and C6).

13.1.4 Antenna coil

The precise calculation of the antenna coils’ inductance is not practicable but the

inductance can be estimated using the following formula. We recommend designing an

antenna either with a circular or rectangular shape.

(4)

•I1 - Length in cm of one turn of the conductor loop

•D1 - Diameter of the wire or width of the PCB conductor respectively

•K - Antenna shape factor (K = 1,07 for circular antennas and K = 1,47 for square

antennas)

•L1 - Inductance in nH

•N1 - Number of turns

•Ln: Natural logarithm function

The actual values of the antenna inductance, resistance, and capacitance at 13.56

MHz depend on various parameters such as:

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 107 / 146

•antenna construction (Type of PCB)

•thickness of conductor

•distance between the windings

•shielding layer

•metal or ferrite in the near environment

Therefore a measurement of those parameters under real life conditions, or at least a

rough measurement and a tuning procedure is highly recommended to guarantee a

reasonable performance. For details refer to the above mentioned application notes.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 108 / 146

14 Package outline

0.51

A1Eh

UNIT ye

0.2

REFERENCES

OUTLINE

VERSION

EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 5.1

4.9

3.25

2.95

5.1

4.9

3.25

2.95

3.5

0.30

0.18

0.05

0.00 0.05 0.1

DIMENSIONS (mm are the original dimensions)

SOT617-1 MO-220- - - - - -

0.5

0.3

0.1

0.05

0 2.5 5 mm

scale

SOT617-1

HVQFN32: plastic thermal enhanced very thin quad flat package; no leads;

32 terminals; body 5 x 5 x 0.85 mm

A(1)

max.

detail X

y1C

9 16

32 25

B A

terminal 1

index area

terminal 1

index area

01-08-08

02-10-18

1/2 e

1/2 eAC

E(1)

Note

1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.

D(1)

Figure 30. Package outline SOT617-1 (HVQFN32)

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 109 / 146

Detailed package information can be found at http://www.nxp.com/package/

SOT617-1.html.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 110 / 146

15 Handling information

Moisture Sensitivity Level (MSL) evaluation has been performed according to SNW-

FQ-225B rev.04/07/07 (JEDEC J-STD-020C). MSL for this package is level 2 which

means 260 °C convection reflow temperature.

For MSL2:

•Dry pack is required.

•1 year out-of-pack floor life at maximum ambient temperature 30 °C/ 85 % RH.

For MSL1:

•No dry pack is required.

•No out-of-pack floor live spec. required.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 111 / 146

16 Packing information

001aaj740

strap 46 mm from corner

tray

chamfer

PIN 1

chamfer

PIN 1

printed plano box

ESD warning preprinted

barcode label (permanent)

barcode label (peel-off)

QA seal

Hyatt patent preprinted

The straps around the package of

stacked trays inside the plano-box

have sufficient pre-tension to avoid

loosening of the trays.

In the traystack (2 trays)

only ONE tray type* allowed

*one supplier and one revision number.

Figure 31. Packing information 1 tray

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 112 / 146

aaa-004952

PQ-label (permanent) bag

strap 46 mm from the corner

dry-agent

ESD warning preprinted

PQ-label (permanent)

dry-pack ID preprinted

strap

QA seal

relative humidity indicator

tray

preprinted:

recycling symbol

moisture caution label

ESD warning

manufacturer bag info

chamfer

printed plano box

PIN 1

PLCC52

Figure 32. Packing information 5 tray

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 113 / 146

1.55

3.00

(0.30)

16.60±0.08+7°/S SQ.

1.20

0.56

3.32

(14.40+5°/S SQ.)

(1.45)

1.10

2.50

(0.64)

0.35

aaa-004949

AL AL AM AM

section BC-BC

scale 4:1

vacuum cell

section BD-BD

scale 4:1

section BA-BA

scale 4:1

detail AC

scale 20:1 section AJ-AJ

scale 2:1

section AR-AR

scale 2:1

section AL-AL

scale 5:1

section AK-AK

scale 5:1

section AM-AM

scale 4:1

section AN-AN

scale 4:1

end lock side lock

12.80-5°/S SQ.

14.20±0.08+10°/S SQ.

13.85±0.08+12°/S SQ.

BA C

0.50

BA C

0.50

Figure 33. Tray details

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 114 / 146

aaa-004950

tape

guard band

circular sprocket holes

opposite the label side of reel

cover tape

carrier tape

enlongated

circular

enlongated

PIN1 has to be

in quadrant 1

QA seal

preprinted ESD warning

PQ-label

dry-pack ID preprinted

(permanent)

product orientation

in carrier tape

product orientation ONLY for turned

products with 12nc ending 128

HOW TO SECURE LEADER END TO THE GUARD BAND,

HOW TO SECURE GUARD BAND

unreeling direction

(see: HOW TO SECURE)

PIN1

PIN1 PIN1

BGA

bare die BGA

bare die for SOT505-2

ending 125

for SOT765

ending 125

PIN1 PIN1 PIN1

PIN1 PIN1

QFP QFP

PLCCSO SO

1 2

3 4

(HV)QFN

(HV)SON

(H)BCC

(HV)QFN

(HV)SON

(H)BCC

1 2

3 4

see: ASSY REEL + LABELS

ASSY REEL + LABELS

label side embossed

ESD logo

embossed

ESD logo

tape

printed plano-box

Ø 330x12/16/24/32 (hub 7'')

Ø 330x16/24/32/44 (hub 4'')

Ø 330x44 (hub 6'')

Ø 180x12/16/24

tapeslot

label side

trailer

leader

leader : lenght of trailer shall be 400 mm min.

and covered with cover tape

circular sprocket hole side

guard band

trailer : lenght of trailer shall be 160 mm min.

and covered with cover tape

tape

(with pull tabs on both ends)

guard band

lape double-backed

onto itself on both ends

Figure 34. Packing information Reel

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 115 / 146

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 116 / 146

17 Appendix

17.1 LoadProtocol command register initialization

The RF configuration is loaded with the command Load Protocol. The tables below

show the register configuration as performed by this command for each of the protocols.

Antenna specific configurations are not covered by this register settings.

The SLRC61002 is not initialized for any antenna configuration. For this products the

antenna configuration needs to be done by firmware.

The SLRC61003 antenna configuration in the user EEPROM is described in the chapter

Section 17.2.

Table 201. Protocol Number 00: ISO/IEC15693 SLI 1/4 - SSC- 26

Value for register Value (hex)

TxBitMod 00

RFU 00

TxDataCon 83

TxDataMod 04

TxSymFreq 40

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

TxSym2 84

TxSym3 02

TxSym10Len 00

TxSym32Len 37

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 00

RxEofSym 1D

RxSyncValH 00

RxSyncValL 01

RxSyncMod 00

RxMod 24

RxCorr 60

FabCal F0

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 117 / 146

Table 202. Protocol Number 01: ISO/IEC15693 SLI 1/4 - SSC- 53

Value for register Value (hex)

TxBitMod 00

RFU 00

TxDataCon 83

TxDataMod 04

TxSymFreq 40

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

TxSym2 84

TxSym3 02

TxSym10Len 00

TxSym32Len 37

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 00

RxEofSym 1D

RxSyncValH 00

RxSyncValL 01

RxSyncMod 00

RxMod 24

RxCorr 40

FabCal F0

Table 203. Protocol Number 02: ISO/IEC15693 SLI 1/256 - DSC

Value for register Value (hex)

TxBitMod 00

RFU 00

TxDataCon 83

TxDataMod 04

TxSymFreq 40

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 118 / 146

Value for register Value (hex)

TxSym2 81

TxSym3 02

TxSym10Len 00

TxSym32Len 37

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 00

RxEofSym 1D

RxSyncValH 00

RxSyncValL 01

RxSyncMod 00

RxMod 26

RxCorr 60

FabCal F0

Table 204. Protocol Number 03: EPC/UID - SSC -26

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon 44

TxDataMod 00

TxSymFreq 44

TxSym0H 08

TxSym0L 22

TxSym1H 08

TxSym1L 28

TxSym2 8A

TxSym3 02

TxSym10Len BB

TxSym32Len 37

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 119 / 146

Value for register Value (hex)

RxSyncValH 00

RxSyncValL 00

RxSyncMod 08

RxMod 04

RxCorr 50

FabCal F0

Table 205. Protocol Number 04: EPC-V2 - 2/424

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon C5

TxDataMod 00

TxSymFreq 05

TxSym0H 68

TxSym0L 41

TxSym1H 01

TxSym1L A1

TxSym2 00

TxSym3 00

TxSym10Len 8E

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

RxSyncValH 00

RxSyncValL 01

RxSyncMod 04

RxMod 0C

RxCorr 40

FabCal F0

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 120 / 146

Table 206. Protocol Number 05: EPC-V2 - 4/424

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon C5

TxDataMod 00

TxSymFreq 05

TxSym0H 68

TxSym0L 41

TxSym1H 01

TxSym1L A1

TxSym2 00

TxSym3 00

TxSym10Len 8E

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

RxSyncValH 00

RxSyncValL 01

RxSyncMod 04

RxMod 0C

RxCorr 50

FabCal F0

Table 207. Protocol Number 06: EPC-V2 - 2/848

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon C5

TxDataMod 00

TxSymFreq 05

TxSym0H 68

TxSym0L 41

TxSym1H 01

TxSym1L A1

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 121 / 146

Value for register Value (hex)

TxSym2 00

TxSym3 00

TxSym10Len 8E

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

RxSyncValH 00

RxSyncValL 01

RxSyncMod 04

RxMod 0C

RxCorr 88

FabCal F0

Table 208. Protocol Number 07: EPC-V2 - 4/848

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon C5

TxDataMod 00

TxSymFreq 05

TxSym0H 68

TxSym0L 41

TxSym1H 01

TxSym1L A1

TxSym2 00

TxSym3 00

TxSym10Len 8E

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 122 / 146

Value for register Value (hex)

RxSyncValH 00

RxSyncValL 01

RxSyncMod 04

RxMod 0C

RxCorr 80

FabCal F0

17.2 SLRC61003 EEPROM configuration

The SLRC61003 user EEPROM had been initalized with useful values for configuration

of the chip using a typical 65x65mm antenna. This values stored in EEPROM can be

used to configure the MFRC61003 with the command LoadReg.Typically, some of this

entries will be required to be modified compared to the preset values to achieve the best

RF performance for a specific antenna.

The registers 0x28...0x39 are relevant for configuration of the Antenna. For each

supported protocol, a dedicated preset configuration is available. To ensure compatibility

between products of the SLRC61003 family, all products use the same default settings

which are initialized in EEPROM, even if some of this protocols are not supported by the

MFRC61003 product (e.g.ISO/IEC14443-A, ISO14443-B) and cannot be used.

Alternatively, the registers can be initialized by individual register write commands.

Table 209. ISO/IEC14443-A 106 / MIFARE Classic

Value for register EEPROM address (hex) Value (hex)

DrvMode C0 8E

TxAmp C1 12

DrvCon C2 39

TxI C3 0A

TXCrcPreset C4 18

RXCrcPreset C5 18

TxDataNum C6 0F

TxModWidth C7 21

TxSym10BurstLen C8 00

TxWaitCtrl C9 C0

TxWaitLo CA 12

TxFrameCon CB CF

RxSofD CC 00

RxCtrl CD 04

RxWait CE 90

RxTreshold CF 5C

Rcv D0 12

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 123 / 146

Value for register EEPROM address (hex) Value (hex)

RxAna D1 0A

Table 210. ISO/IEC14443-A 212/ MIFARE Classic

Value for register EEPROM address (hex) Value (hex)

DrvMode D4 8E

TxAmp D5 D2

DrvCon D6 11

TxI D7 0A

TXCrcPreset D8 18

RXCrcPreset D9 18

TxDataNum DA 0F

TxModWidth DB 10

TxSym10BurstLen DC 00

TxWaitCtrl DD C0

TxWaitLo DE 12

TxFrameCon DF CF

RxSofD E0 00

RxCtrl E1 05

RxWait E2 90

RxTreshold E3 3C

Rcv E4 12

RxAna E5 0B

Table 211. ISO/IEC14443-A 424/ MIFARE Classic

Value for register EEPROM address (hex) Value (hex)

DrvMode E8 8F

TxAmp E9 DE

DrvCon EA 11

TxI EB 0F

TXCrcPreset EC 18

RXCrcPreset ED 18

TxDataNum EE 0F

TxModWidth EF 07

TxSym10BurstLen F0 00

TxWaitCtrl F1 C0

TxWaitLo F2 12

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 124 / 146

Value for register EEPROM address (hex) Value (hex)

TxFrameCon F3 CF

RxSofD F4 00

RxCtrl F5 06

RxWait F6 90

RxTreshold F7 2B

Rcv F8 12

RxAna F9 0B

Table 212. ISO/IEC14443-A 848/ MIFARE Classic

Value for register EEPROM address (hex) Value (hex)

DrvMode 0100 8F

TxAmp 0101 DB

DrvCon 0102 21

TxI 0103 0F

TXCrcPreset 0104 18

RXCrcPreset 0105 18

TxDataNum 0106 0F

TxModWidth 0107 02

TxSym10BurstLen 0108 00

TxWaitCtrl 0109 C0

TxWaitLo 010A 12

TxFrameCon 010B CF

RxSofD 010C 00

RxCtrl 010D 07

RxWait 010E 90

RxTreshold 010F 3A

Rcv 0110 12

RxAna 0111 0B

Table 213. ISO/IEC14443-B 106

Value for register EEPROM address (hex) Value (hex)

DrvMode 0114 8F

TxAmp 0115 0E

DrvCon 0116 09

TxI 0117 0A

TXCrcPreset 0118 7B

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 125 / 146

Value for register EEPROM address (hex) Value (hex)

RXCrcPreset 0119 7B

TxDataNum 011A 08

TxModWidth 011B 00

TxSym10BurstLen 011C 00

TxWaitCtrl 011D 01

TxWaitLo 011E 00

TxFrameCon 011F 05

RxSofD 0120 00

RxCtrl 0121 34

RxWait 0112 90

RxTreshold 0113 6F

Rcv 0114 12

RxAna 0115 03

Table 214. ISO/IEC14443-B 212

Value for register EEPROM address (hex) Value (hex)

DrvMode 0128 8F

TxAmp 0129 0E

DrvCon 012A 09

TxI 012B 0A

TXCrcPreset 012C 7B

RXCrcPreset 012D 7B

TxDataNum 012E 08

TxModWidth 012F 00

TxSym10BurstLen 0130 00

TxWaitCtrl 0131 01

TxWaitLo 0132 00

TxFrameCon 0133 05

RxSofD 0134 00

RxCtrl 0135 35

RxWait 0136 90

RxTreshold 0137 3F

Rcv 0138 12

RxAna 0139 03

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 126 / 146

Table 215. ISO/IEC14443-B 424

Value for register EEPROM address (hex) Value (hex)

DrvMode 0140 8F

TxAmp 0141 0F

DrvCon 0142 09

TxI 0143 0A

TXCrcPreset 0144 7B

RXCrcPreset 0145 7B

TxDataNum 0146 08

TxModWidth 0147 00

TxSym10BurstLen 0148 00

TxWaitCtrl 0149 01

TxWaitLo 014A 00

TxFrameCon 014B 05

RxSofD 014C 00

RxCtrl 014D 36

RxWait 014E 90

RxTreshold 014F 3F

Rcv 0150 12

RxAna 0151 03

Table 216. ISO/IEC14443-B 848

Value for register EEPROM address (hex) Value (hex)

DrvMode 0154 8F

TxAmp 0155 10

DrvCon 0156 09

TxI 0157 0A

TXCrcPreset 0158 7B

RXCrcPreset 0159 7B

TxDataNum 015A 08

TxModWidth 015B 00

TxSym10BurstLen 015C 00

TxWaitCtrl 015D 01

TxWaitLo 015E 00

TxFrameCon 015F 05

RxSofD 0160 00

RxCtrl 0161 37

RxWait 0162 90

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 127 / 146

Value for register EEPROM address (hex) Value (hex)

RxTreshold 0163 3F

Rcv 0164 12

RxAna 0165 03

The following EEprom values for initializing the Receiver cannot be used on the

MFRC63103. They are provided for compatibility reasons between the products of the

CLRC66303 product family

Table 217. JIS X 6319-4 (FeliCa) 212

Value for register EEPROM address (hex) Value (hex)

DrvMode 0168 8F

TxAmp 0169 17

DrvCon 016A 01

TxI 016B 06

TXCrcPreset 016C 09

RXCrcPreset 016D 09

TxDataNum 016E 08

TxModWidth 016F 00

TxSym10BurstLen 0170 03

TxWaitCtrl 0171 80

TxWaitLo 0172 12

TxFrameCon 0173 01

RxSofD 0174 00

RxCtrl 0175 05

RxWait 0176 86

RxTreshold 0177 3F

Rcv 0178 12

RxAna 0179 02

Table 218. JIS X 6319-4 (FeliCa) 424

Value for register EEPROM address (hex) Value (hex)

DrvMode 0180 8F

TxAmp 0181 17

DrvCon 0182 01

TxI 0183 06

TXCrcPreset 0184 09

RXCrcPreset 0185 09

TxDataNum 0186 08

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 128 / 146

Value for register EEPROM address (hex) Value (hex)

TxModWidth 0187 00

TxSym10BurstLen 0188 03

TxWaitCtrl 0189 80

TxWaitLo 018A 12

TxFrameCon 018B 01

RxSofD 018C 00

RxCtrl 018D 06

RxWait 018E 86

RxTreshold 018F 3F

Rcv 0190 12

RxAna 0191 02

Table 219. ISO/IEC15693 SLI 1/4 - SSC- 26

Value for register EEPROM address (hex) Value (hex)

DrvMode 0194 89

TxAmp 0195 10

DrvCon 0196 09

TxI 0197 0A

TXCrcPreset 0198 7B

RXCrcPreset 0199 7B

TxDataNum 019A 08

TxModWidth 019B 00

TxSym10BurstLen 019C 00

TxWaitCtrl 019D 88

TxWaitLo 019E A9

TxFrameCon 019F 0F

RxSofD 01A0 00

RxCtrl 01A1 02

RxWait 01A2 9C

RxTreshold 01A3 74

Rcv 01A4 12

RxAna 01A5 07

Table 220. ISO/IEC15693 SLI 1/4 - SSC-53

Value for register EEPROM address (hex) Value (hex)

DrvMode 01A8 89

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 129 / 146

Value for register EEPROM address (hex) Value (hex)

TxAmp 01A9 10

DrvCon 01AA 09

TxI 01AB 0A

TXCrcPreset 01AC 7B

RXCrcPreset 01AD 7B

TxDataNum 01AE 08

TxModWidth 016F 00

TxSym10BurstLen 01B0 00

TxWaitCtrl 01B1 88

TxWaitLo 01B2 A9

TxFrameCon 01B3 0F

RxSofD 01B4 00

RxCtrl 01B5 03

RxWait 01B6 9C

RxTreshold 01B7 74

Rcv 01B8 12

RxAna 01B9 03

Table 221. ISO/IEC15693 SLI 1/256 - DSC

Value for register EEPROM address (hex) Value (hex)

DrvMode 01C0 8E

TxAmp 01C1 10

DrvCon 01C2 01

TxI 01C3 06

TXCrcPreset 01C4 7B

RXCrcPreset 01C5 7B

TxDataNum 01C6 08

TxModWidth 01C7 00

TxSym10BurstLen 01C8 00

TxWaitCtrl 01C9 88

TxWaitLo 01CA A9

TxFrameCon 01CB 0F

RxSofD 01CC 00

RxCtrl 01CD 02

RxWait 01CE 10

RxTreshold 01CF 44

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 130 / 146

Value for register EEPROM address (hex) Value (hex)

Rcv 01D0 12

RxAna 01D1 06

Table 222. EPC/UID - SSC -26

Value for register EEPROM address (hex) Value (hex)

DrvMode 01D4 8F

TxAmp 01D5 10

DrvCon 01D6 01

TxI 01D7 06

TXCrcPreset 01D8 74

RXCrcPreset 01D9 7B

TxDataNum 01DA 18

TxModWidth 01DB 00

TxSym10BurstLen 01DC 00

TxWaitCtrl 01DD 50

TxWaitLo 01DE 5C

TxFrameCon 01DF 0F

RxSofD 01E0 00

RxCtrl 01E1 03

RxWait 01E2 10

RxTreshold 01E3 4E

Rcv 01E4 12

RxAna 01E5 06

Table 223. EPC-V2 - 2/424

Value for register EEPROM address (hex) Value (hex)

DrvMode 01E8 8F

TxAmp 01E9 10

DrvCon 01EA 09

TxI 01EB 0A

TXCrcPreset 01EC 11

RXCrcPreset 01ED 91

TxDataNum 01EE 09

TxModWidth 01EF 00

TxSym10BurstLen 01F0 00

TxWaitCtrl 01F1 80

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 131 / 146

Value for register EEPROM address (hex) Value (hex)

TxWaitLo 01F2 12

TxFrameCon 01F3 01

RxSofD 01F4 00

RxCtrl 01F5 03

RxWait 01F6 A0

RxTreshold 01F7 56

Rcv 01F8 12

RxAna 01F9 0F

Table 224. EPC-V2 - 4/424

Value for register EEPROM address (hex) Value (hex)

DrvMode 0200 8F

TxAmp 0201 10

DrvCon 0202 09

TxI 0203 0A

TXCrcPreset 0204 11

RXCrcPreset 0205 91

TxDataNum 0206 09

TxModWidth 0207 00

TxSym10BurstLen 0208 00

TxWaitCtrl 0209 80

TxWaitLo 020A 12

TxFrameCon 020B 01

RxSofD 020C 00

RxCtrl 020D 03

RxWait 020E A0

RxTreshold 020F 56

Rcv 0210 12

RxAna 0211 0F

Table 225. EPC-V2 - 2/848

Value for register EEPROM address (hex) Value (hex)

DrvMode 0214 8F

TxAmp 0215 D0

DrvCon 0216 01

TxI 0217 0A

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 132 / 146

Value for register EEPROM address (hex) Value (hex)

TXCrcPreset 0218 11

RXCrcPreset 0219 91

TxDataNum 021A 09

TxModWidth 021B 00

TxSym10BurstLen 021C 00

TxWaitCtrl 021D 80

TxWaitLo 021E 12

TxFrameCon 021F 01

RxSofD 0220 00

RxCtrl 0221 05

RxWait 0222 A0

RxTreshold 0223 26

Rcv 0224 12

RxAna 0225 0E

Table 226. EPC-V2 - 4/848

Value for register EEPROM address (hex) Value (hex)

DrvMode 0228 8F

TxAmp 0229 D0

DrvCon 022A 01

TxI 022B 0A

TXCrcPreset 022C 11

RXCrcPreset 022D 91

TxDataNum 022E 09

TxModWidth 022F 00

TxSym10BurstLen 0230 00

TxWaitCtrl 0231 80

TxWaitLo 0232 12

TxFrameCon 0233 01

RxSofD 0234 00

RxCtrl 0235 05

RxWait 0236 A0

RxTreshold 0237 26

Rcv 0238 12

RxAna 0239 0E

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 133 / 146

Table 227. Jewel

Value for register EEPROM address (hex) Value (hex)

DrvMode 0240 8E

TxAmp 0241 15

DrvCon 0242 11

TxI 0243 06

TXCrcPreset 0244 18

RXCrcPreset 0245 18

TxDataNum 0246 0F

TxModWidth 0247 20

TxSym10BurstLen 0248 00

TxWaitCtrl 0249 40

TxWaitLo 024A 09

TxFrameCon 024B 4F

RxSofD 024C 00

RxCtrl 024D 04

RxWait 024E 8F

RxTreshold 024F 32

Rcv 0250 12

RxAna 0251 0A

Table 228. ISO/IEC14443 - B 106 EMVCo Optimized

Value for register EEPROM address (hex) Value (hex)

DrvMode 0254 8F

TxAmp 0255 0E

DrvCon 0256 09

TxI 0257 0A

TXCrcPreset 0258 7B

RXCrcPreset 0259 7B

TxDataNum 025A 08

TxModWidth 025B 00

TxSym10BurstLen 025C 00

TxWaitCtrl 025D 01

TxWaitLo 025E 00

TxFrameCon 025F 05

RxSofD 0260 00

RxCtrl 0261 34

RxWait 0262 90

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 134 / 146

Value for register EEPROM address (hex) Value (hex)

RxTreshold 0263 9F

Rcv 0264 12

RxAna 0265 03

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 135 / 146

18 Abbreviations

Table 229. Abbreviations

Acronym Description

ADC Analog-to-Digital Converter

BPSK Binary Phase Shift Keying

CRC Cyclic Redundancy Check

CW Continuous Wave

EGT Extra Guard Time

EMC Electro Magnetic Compatibility

EMD Electro Magnetic Disturbance

EOF End Of Frame

EPC Electronic Product Code

ETU Elementary Time Unit

GPIO General Purpose Input/Output

HBM Human Body Model

I2C Inter-Integrated Circuit

IRQ Interrupt Request

LFO Low Frequency Oscillator

LPCD Low-Power Card Detection

LSB Least Significant Bit

MISO Master In Slave Out

MOSI Master Out Slave In

MSB Most Significant Bit

NRZ Not Return to Zero

NSS Not Slave Select

PCD Proximity Coupling Device

PLL Phase-Locked Loop

RZ Return To Zero

RX Receiver

SAM Secure Access Module

SOF Start Of Frame

SPI Serial Peripheral Interface

SW Software

TTimer Timing of the clk period

TX Transmitter

UART Universal Asynchronous Receiver Transmitter

UID Unique IDentification

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 136 / 146

Acronym Description

VCO Voltage Controlled Oscillator

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 137 / 146

19 References

[1]

Application note AN11019

CLRC663, MFRC630, MFRC631, SLRC610 Antenna Design Guide

[2]

Application note AN11783

CLRC663 plus Low Power Card Detection

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 138 / 146

20 Revision history

Table 230. Revision history

Document ID Release date Data sheet status Change notice Supersedes

SLRC610 v. 4.6 20180912 Product data sheet - SLRC610 v. 4.5

Modifications: •Description of Low frequency timer in Section 7.8.3 more detailed now

SLRC610 v. 4.5 20180627 Product data sheet - SLRC610 v. 4.4

Modifications: •Editorial updates

SLRC610 v. 4.4 20171219 Product data sheet - SLRC610 v. 4.3

Modifications: •Deleted References to MICORE Application notes

SLRC610 v. 4.3 20170801 Product data sheet - SLRC610 v. 4.2

Modifications: •Description for new product type SLRC61003 added

•Section 19: updated

SLRC610 v. 4.2 20160427 Product data sheet - SLRC610 v.4.1

Modifications: •Descriptive title changed

SLRC610 v. 4.1 20160211 Product data sheet - SLRC610 v.3.3

Modifications: •Table Quick reference data: Table notes [3] and [4] removed

•Table Characteristics:

–AVDD and DVDD min and max values added

–IDD(TVDD) max value updated to 250 mA

•Figure 7 "Connection to host with SPI": updated

•Figure 16 "Register read and write access": updated

SLRC610 v.3.3 20140204 Product data sheet SLRC610 v.3.2

Modifications: •PVDD, TVDD data updated

•Information on FIFO size corrected

•Typing error corrected in description for LPCD

•WaterLevel and FIFOLength updated in register overview description

•WaterLevel and FIFOLength updated in register FIFOControl

•Waterlevel Register updated

•FIFOLength Register updated

•Section 8.15.2 "PinOut": Pin Out register description corrected

SLRC610 v.3.2 20130312 Product data sheet - SLRC610 v.3.1

Modifications: •Update of EEPROM content

•Descriptive title changed

•Table 183 "PinOut register (address 45h)": corrected

SLRC610 v.3.1 20120906 Product data sheet - -

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 139 / 146

21 Legal information

21.1 Data sheet status

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objective specification for product

development.

Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.

Product [short] data sheet Production This document contains the product specification.

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term 'short data sheet' is explained in section "Definitions".

[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple

devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

21.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences

of use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is

intended for quick reference only and should not be relied upon to contain

detailed and full information. For detailed and full information see the

relevant full data sheet, which is available on request via the local NXP

Semiconductors sales office. In case of any inconsistency or conflict with the

short data sheet, the full data sheet shall prevail.

Product specification — The information and data provided in a Product

data sheet shall define the specification of the product as agreed between

NXP Semiconductors and its customer, unless NXP Semiconductors and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the NXP Semiconductors product

is deemed to offer functions and qualities beyond those described in the

Product data sheet.

21.3 Disclaimers

Limited warranty and liability — Information in this document is believed

to be accurate and reliable. However, NXP Semiconductors does not

give any representations or warranties, expressed or implied, as to the

accuracy or completeness of such information and shall have no liability

for the consequences of use of such information. NXP Semiconductors

takes no responsibility for the content in this document if provided by an

information source outside of NXP Semiconductors. In no event shall NXP

Semiconductors be liable for any indirect, incidental, punitive, special or

consequential damages (including - without limitation - lost profits, lost

savings, business interruption, costs related to the removal or replacement

of any products or rework charges) whether or not such damages are based

on tort (including negligence), warranty, breach of contract or any other

legal theory. Notwithstanding any damages that customer might incur for

any reason whatsoever, NXP Semiconductors’ aggregate and cumulative

liability towards customer for the products described herein shall be limited

in accordance with the Terms and conditions of commercial sale of NXP

Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to

make changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reasonably be expected

to result in personal injury, death or severe property or environmental

damage. NXP Semiconductors and its suppliers accept no liability for

inclusion and/or use of NXP Semiconductors products in such equipment or

applications and therefore such inclusion and/or use is at the customer’s own

risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes

no representation or warranty that such applications will be suitable

for the specified use without further testing or modification. Customers

are responsible for the design and operation of their applications and

products using NXP Semiconductors products, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suitable and fit for the customer’s applications

and products planned, as well as for the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with

their applications and products. NXP Semiconductors does not accept any

liability related to any default, damage, costs or problem which is based

on any weakness or default in the customer’s applications or products, or

the application or use by customer’s third party customer(s). Customer is

responsible for doing all necessary testing for the customer’s applications

and products using NXP Semiconductors products in order to avoid a

default of the applications and the products or of the application or use by

customer’s third party customer(s). NXP does not accept any liability in this

respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those

given in the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanently and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individual agreement. In case an individual

agreement is concluded only the terms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby expressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

No offer to sell or license — Nothing in this document may be interpreted

or construed as an offer to sell products that is open for acceptance or

the grant, conveyance or implication of any license under any copyrights,

patents or other industrial or intellectual property rights.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 140 / 146

Quick reference data — The Quick reference data is an extract of the

product data given in the Limiting values and Characteristics sections of this

document, and as such is not complete, exhaustive or legally binding.

Export control — This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a prior

authorization from competent authorities.

Non-automotive qualified products — Unless this data sheet expressly

states that this specific NXP Semiconductors product is automotive qualified,

the product is not suitable for automotive use. It is neither qualified nor

tested in accordance with automotive testing or application requirements.

NXP Semiconductors accepts no liability for inclusion and/or use of non-

automotive qualified products in automotive equipment or applications. In

the event that customer uses the product for design-in and use in automotive

applications to automotive specifications and standards, customer (a) shall

use the product without NXP Semiconductors’ warranty of the product for

such automotive applications, use and specifications, and (b) whenever

customer uses the product for automotive applications beyond NXP

Semiconductors’ specifications such use shall be solely at customer’s own

risk, and (c) customer fully indemnifies NXP Semiconductors for any liability,

damages or failed product claims resulting from customer design and use

of the product for automotive applications beyond NXP Semiconductors’

standard warranty and NXP Semiconductors’ product specifications.

Translations — A non-English (translated) version of a document is for

reference only. The English version shall prevail in case of any discrepancy

between the translated and English versions.

21.4 Licenses

Purchase of NXP ICs with ISO/IEC 14443 type B functionality

RATP/Innovatron

Technology

This NXP Semiconductors IC is ISO/IEC

14443 Type B software enabled and is

licensed under Innovatron’s Contactless

Card patents license for ISO/IEC 14443 B.

The license includes the right to use the IC

in systems and/or end-user equipment.

Purchase of NXP ICs with NFC technology

Purchase of an NXP Semiconductors IC that complies with one of the

Near Field Communication (NFC) standards ISO/IEC 18092 and ISO/

IEC 21481 does not convey an implied license under any patent right

infringed by implementation of any of those standards. Purchase of NXP

Semiconductors IC does not include a license to any NXP patent (or other

IP right) covering combinations of those products with other products,

whether hardware or software.

21.5 Trademarks

Notice: All referenced brands, product names, service names and

trademarks are the property of their respective owners.

I2C-bus — logo is a trademark of NXP B.V.

MIFARE — is a trademark of NXP B.V.

DESFire — is a trademark of NXP B.V.

ICODE and I-CODE — are trademarks of NXP B.V.

MIFARE Plus — is a trademark of NXP B.V.

MIFARE Ultralight — is a trademark of NXP B.V.

MIFARE Classic — is a trademark of NXP B.V.

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 141 / 146

Tables

Tab. 1. Quick reference data SLRC61002HN ............... 3

Tab. 2. Quick reference data SLRC61003HN ............... 3

Tab. 3. Ordering information ..........................................4

Tab. 4. Pin description ...................................................6

Tab. 5. Interrupt sources ............................................... 9

Tab. 6. Communication overview for ISO/IEC 15693

reader/writer reader to label ............................ 12

Tab. 7. Communication overview for ISO/IEC 15693

reader/writer label to reader ............................ 12

Tab. 8. Communication overview for EPC/UID ............13

Tab. 9. Connection scheme for detecting the

different interface types ...................................14

Tab. 10. Byte Order for MOSI and MISO ...................... 15

Tab. 11. Byte Order for MOSI and MISO ...................... 16

Tab. 12. Address byte 0 register; address MOSI ...........16

Tab. 13. Timing conditions SPI ..................................... 16

Tab. 14. Settings of BR_T0 and BR_T1 ........................17

Tab. 15. Selectable transfer speeds ..............................17

Tab. 16. UART framing ................................................. 18

Tab. 17. Byte Order to Read Data ................................ 18

Tab. 18. Byte Order to Write Data ................................ 19

Tab. 19. Timing parameter I2CL ................................... 24

Tab. 20. SPI SAM connection ....................................... 25

Tab. 21. Boundary scan command ............................... 26

Tab. 22. Boundary scan path of the SLRC610 ..............28

Tab. 23. Settings for TX1 and TX2 ............................... 32

Tab. 24. Setting residual carrier and modulation

index by TXamp.set_residual_carrier .............. 32

Tab. 25. Configuration for single or differential

receiver ............................................................35

Tab. 26. Register configuration of SLRC610 active

antenna concept (DIGITAL) ............................ 36

Tab. 27. Register configuration of SLRC610 active

antenna concept (Antenna) .............................36

Tab. 28. EEPROM memory organization ...................... 40

Tab. 29. Production area (Page 0) ................................40

Tab. 30. Product ID overview of CLRC663 family ......... 41

Tab. 31. Configuration area (Page 0) ............................41

Tab. 32. Interface byte .................................................. 41

Tab. 33. Interface bits ....................................................41

Tab. 34. Tx and Rx arrangements in the register set

protocol area ................................................... 42

Tab. 35. Register reset values (Hex.) (Page0) .............. 42

Tab. 36. Register reset values (Hex.)(Page1 and

page 2) ............................................................43

Tab. 37. Crystal requirements recommendations ..........44

Tab. 38. Divider values for selected frequencies

using the integerN PLL ................................... 45

Tab. 39. Command set ..................................................48

Tab. 40. Predefined protocol overview RXFor more

protocol details please refer to Section 7

"Functional description". ..................................51

Tab. 41. Predefined protocol overview TXFor more

protocol details please refer to Section 7

"Functional description". ..................................51

Tab. 42. Behavior of register bits and their

designation ...................................................... 53

Tab. 43. SLRC610 registers overview ...........................53

Tab. 44. Command register (address 00h) ....................56

Tab. 45. Command bits ................................................. 56

Tab. 46. HostCtrl register (address 01h); ...................... 56

Tab. 47. HostCtrl bits .....................................................57

Tab. 48. FIFOControl register (address 02h); ............... 57

Tab. 49. FIFOControl bits .............................................. 57

Tab. 50. WaterLevel register (address 03h); ................. 58

Tab. 51. WaterLevel bits ............................................... 58

Tab. 52. FIFOLength register (address 04h); reset

value: 00h ........................................................59

Tab. 53. FIFOLength bits .............................................. 59

Tab. 54. FIFOData register (address 05h); ................... 59

Tab. 55. FIFOData bits ..................................................59

Tab. 56. IRQ0 register (address 06h); reset value:

00h .................................................................. 60

Tab. 57. IRQ0 bits ......................................................... 60

Tab. 58. IRQ1 register (address 07h) ............................60

Tab. 59. IRQ1 bits ......................................................... 61

Tab. 60. IRQ0En register (address 08h) ....................... 61

Tab. 61. IRQ0En bits .....................................................61

Tab. 62. IRQ1EN register (address 09h); ......................62

Tab. 63. IRQ1EN bits .................................................... 62

Tab. 64. Error register (address 0Ah) ............................62

Tab. 65. Error bits ..........................................................63

Tab. 66. Status register (address 0Bh) ......................... 63

Tab. 67. Status bits ....................................................... 64

Tab. 68. RxBitCtrl register (address 0Ch); .................... 64

Tab. 69. RxBitCtrl bits ................................................... 64

Tab. 70. RxColl register (address 0Dh); ........................ 65

Tab. 71. RxColl bits ....................................................... 65

Tab. 72. TControl register (address 0Eh) ......................66

Tab. 73. TControl bits ....................................................66

Tab. 74. T0Control register (address 0Fh); ................... 66

Tab. 75. T0Control bits ..................................................66

Tab. 76. T0ReloadHi register (address 10h); ................ 67

Tab. 77. T0ReloadHi bits ...............................................67

Tab. 78. T0ReloadLo register (address 11h); ................67

Tab. 79. T0ReloadLo bits .............................................. 68

Tab. 80. T0CounterValHi register (address 12h) ...........68

Tab. 81. T0CounterValHi bits ........................................ 68

Tab. 82. T0CounterValLo register (address 13h) .......... 68

Tab. 83. T0CounterValLo bits ........................................68

Tab. 84. T1Control register (address 14h); ................... 68

Tab. 85. T1Control bits ..................................................69

Tab. 86. T0ReloadHi register (address 15h) ................. 69

Tab. 87. T1ReloadHi bits ...............................................69

Tab. 88. T1ReloadLo register (address 16h) .................69

Tab. 89. T1ReloadValLo bits .........................................70

Tab. 90. T1CounterValHi register (address 17h) ...........70

Tab. 91. T1CounterValHi bits ........................................ 70

Tab. 92. T1CounterValLo register (address 18h) .......... 70

Tab. 93. T1CounterValLo bits ........................................70

Tab. 94. T2Control register (address 19h) .................... 70

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 142 / 146

Tab. 95. T2Control bits ..................................................71

Tab. 96. T2ReloadHi register (address 1Ah) .................71

Tab. 97. T2Reload bits .................................................. 71

Tab. 98. T2ReloadLo register (address 1Bh) ................ 71

Tab. 99. T2ReloadLo bits .............................................. 72

Tab. 100. T2CounterValHi register (address 1Ch) .......... 72

Tab. 101. T2CounterValHi bits ........................................ 72

Tab. 102. T2CounterValLo register (address 1Dh) ..........72

Tab. 103. T2CounterValLo bits ........................................72

Tab. 104. T3Control register (address 1Eh) .................... 73

Tab. 105. T3Control bits ..................................................73

Tab. 106. T3ReloadHi register (address 1Fh); ................ 73

Tab. 107. T3ReloadHi bits ...............................................73

Tab. 108. T3ReloadLo register (address 20h) .................74

Tab. 109. T3ReloadLo bits .............................................. 74

Tab. 110. T3CounterValHi register (address 21h) ...........74

Tab. 111. T3CounterValHi bits ........................................ 74

Tab. 112. T3CounterValLo register (address 22h) .......... 74

Tab. 113. T3CounterValLo bits ........................................75

Tab. 114. T4Control register (address 23h) .................... 75

Tab. 115. T4Control bits ..................................................75

Tab. 116. T4ReloadHi register (address 24h) ................. 76

Tab. 117. T4ReloadHi bits ...............................................76

Tab. 118. T4ReloadLo register (address 25h) .................76

Tab. 119. T4ReloadLo bits .............................................. 76

Tab. 120. T4CounterValHi register (address 26h) ...........76

Tab. 121. T4CounterValHi bits ........................................ 77

Tab. 122. T4CounterValLo register (address 27h) .......... 77

Tab. 123. T4CounterValLo bits ........................................77

Tab. 124. DrvMode register (address 28h) ......................77

Tab. 125. DrvMode bits ................................................... 77

Tab. 126. TxAmp register (address 29h) .........................78

Tab. 127. TxAmp bits ...................................................... 78

Tab. 128. TxCon register (address 2Ah) ......................... 78

Tab. 129. TxCon bits ....................................................... 78

Tab. 130. Txl register (address 2Bh) ...............................79

Tab. 131. Txl bits .............................................................79

Tab. 132. TXCrcPreset register (address 2Ch) ............... 79

Tab. 133. TxCrcPreset bits ..............................................79

Tab. 134. Transmitter CRC preset value configuration ....80

Tab. 135. RxCrcCon register (address 2Dh) ................... 80

Tab. 136. RxCrcCon bits ................................................. 80

Tab. 137. Receiver CRC preset value configuration ....... 81

Tab. 138. TxDataNum register (address 2Eh) .................81

Tab. 139. TxDataNum bits .............................................. 81

Tab. 140. TxSym10BurstLen register (address 30h) ....... 82

Tab. 141. TxSym10BurstLen bits .................................... 82

Tab. 142. TxWaitCtrl register (address 31h); reset

value: C0h ....................................................... 82

Tab. 143. TXWaitCtrl bits ................................................ 82

Tab. 144. TxWaitLo register (address 32h) ..................... 83

Tab. 145. TxWaitLo bits .................................................. 83

Tab. 146. FrameCon register (address 33h) ................... 83

Tab. 147. FrameCon bits .................................................83

Tab. 148. RxSofD register (address 34h) ........................84

Tab. 149. RxSofD bits ..................................................... 84

Tab. 150. RxCtrl register (address 35h) .......................... 84

Tab. 151. RxCtrl bits ........................................................85

Tab. 152. RxWait register (address 36h) ........................ 85

Tab. 153. RxWait bits ...................................................... 85

Tab. 154. RxThreshold register (address 37h) ................ 85

Tab. 155. RxThreshold bits ............................................. 86

Tab. 156. Rcv register (address 38h) ..............................86

Tab. 157. Rcv bits ........................................................... 86

Tab. 158. RxAna register (address 39h) ......................... 86

Tab. 159. RxAna bits .......................................................87

Tab. 160. Effect of gain and highpass corner register

settings ............................................................ 87

Tab. 161. SerialSpeed register (address3Bh); reset

value: 7Ah ....................................................... 88

Tab. 162. SerialSpeed bits .............................................. 88

Tab. 163. RS232 speed settings .....................................88

Tab. 164. LFO_Trim register (address 3Ch) ................... 88

Tab. 165. LFO_Trim bits ................................................. 89

Tab. 166. PLL_Ctrl register (address3Dh) .......................89

Tab. 167. PLL_Ctrl register bits .......................................89

Tab. 168. Setting of feedback divider PLLDiv_FB [1:0] ....89

Tab. 169. PLLDiv_Out register (address 3Eh) ................ 90

Tab. 170. PLLDiv_Out bits .............................................. 90

Tab. 171. Setting for the output divider ratio

PLLDiv_Out [7:0] .............................................90

Tab. 172. LPCD_QMin register (address 3Fh) ................ 90

Tab. 173. LPCD_QMin bits ............................................. 91

Tab. 174. LPCD_QMax register (address 40h) ............... 91

Tab. 175. LPCD_QMax bits ............................................ 91

Tab. 176. LPCD_IMin register (address 41h) ..................91

Tab. 177. LPCD_IMin bits ............................................... 92

Tab. 178. LPCD_Result_I register (address 42h) ............92

Tab. 179. LPCD_I_Result bits ......................................... 92

Tab. 180. LPCD_Result_Q register (address 43h) ..........92

Tab. 181. LPCD_Q_Result bits ....................................... 92

Tab. 182. LPCD_Options register (address 3Ah) ............ 93

Tab. 183. LPCD_Options .................................................93

Tab. 184. PinEn register (address 44h) .......................... 93

Tab. 185. PinEn bits ........................................................ 93

Tab. 186. PinOut register (address 45h) ......................... 94

Tab. 187. PinOut bits .......................................................94

Tab. 188. PinIn register (address 46h) ............................95

Tab. 189. PinIn bits ......................................................... 95

Tab. 190. SigOut register (address 47h) ......................... 95

Tab. 191. SigOut bits .......................................................95

Tab. 192. Version register (address 7Fh) ........................96

Tab. 193. Version bits ..................................................... 96

Tab. 194. Limiting values ................................................ 97

Tab. 195. Operating conditions SLRC61002HN ..............98

Tab. 196. Operating conditions SLRC61003HN ..............98

Tab. 197. Thermal characteristics ................................... 99

Tab. 198. Characteristics ...............................................100

Tab. 199. SPI timing characteristics ..............................103

Tab. 200. I2C-bus timing in fast mode and fast mode

plus ................................................................103

Tab. 201. Protocol Number 00: ISO/IEC15693 SLI 1/4

- SSC- 26 ...................................................... 116

Tab. 202. Protocol Number 01: ISO/IEC15693 SLI 1/4

- SSC- 53 ...................................................... 117

Tab. 203. Protocol Number 02: ISO/IEC15693 SLI

1/256 - DSC .................................................. 117

Tab. 204. Protocol Number 03: EPC/UID - SSC -26 ..... 118

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 143 / 146

Tab. 205. Protocol Number 04: EPC-V2 - 2/424 ........... 119

Tab. 206. Protocol Number 05: EPC-V2 - 4/424 ........... 120

Tab. 207. Protocol Number 06: EPC-V2 - 2/848 ........... 120

Tab. 208. Protocol Number 07: EPC-V2 - 4/848 ........... 121

Tab. 209. ISO/IEC14443-A 106 / MIFARE Classic ........122

Tab. 210. ISO/IEC14443-A 212/ MIFARE Classic .........123

Tab. 211. ISO/IEC14443-A 424/ MIFARE Classic .........123

Tab. 212. ISO/IEC14443-A 848/ MIFARE Classic .........124

Tab. 213. ISO/IEC14443-B 106 .....................................124

Tab. 214. ISO/IEC14443-B 212 .....................................125

Tab. 215. ISO/IEC14443-B 424 .....................................126

Tab. 216. ISO/IEC14443-B 848 .....................................126

Tab. 217. JIS X 6319-4 (FeliCa) 212 ............................ 127

Tab. 218. JIS X 6319-4 (FeliCa) 424 ............................ 127

Tab. 219. ISO/IEC15693 SLI 1/4 - SSC- 26 ..................128

Tab. 220. ISO/IEC15693 SLI 1/4 - SSC-53 ................... 128

Tab. 221. ISO/IEC15693 SLI 1/256 - DSC .................... 129

Tab. 222. EPC/UID - SSC -26 ...................................... 130

Tab. 223. EPC-V2 - 2/424 .............................................130

Tab. 224. EPC-V2 - 4/424 .............................................131

Tab. 225. EPC-V2 - 2/848 .............................................131

Tab. 226. EPC-V2 - 4/848 .............................................132

Tab. 227. Jewel ............................................................. 133

Tab. 228. ISO/IEC14443 - B 106 EMVCo Optimized .... 133

Tab. 229. Abbreviations .................................................135

Tab. 230. Revision history ............................................. 138

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 144 / 146

Figures

Fig. 1. Simplified block diagram of the SLRC610 ......... 5

Fig. 2. Pinning configuration HVQFN32

(SOT617-1) ........................................................6

Fig. 3. Detailed block diagram of the SLRC610 ........... 8

Fig. 4. Read/write mode ............................................. 12

Fig. 5. Data coding according to ISO/IEC 15693.

standard mode reader to label ........................ 13

Fig. 6. Connection to host with SPI ............................15

Fig. 7. Connection to host with SPI ............................17

Fig. 8. Example for UART Read ................................ 19

Fig. 9. Example diagram for a UART write .................19

Fig. 10. I2C-bus interface .............................................20

Fig. 11. Bit transfer on the I2C-bus. ............................. 20

Fig. 12. START and STOP conditions ......................... 21

Fig. 13. Acknowledge on the I2C- bus ......................... 22

Fig. 14. Data transfer on the I2C- bus ......................... 22

Fig. 15. First byte following the START procedure .......22

Fig. 16. Register read and write access .......................24

Fig. 17. Boundary scan cell path structure ...................28

Fig. 18. General dependences of modulation .............. 31

Fig. 19. Example 1: overshoot_t1 = 2d; overhoot_t2

= 5d. ................................................................ 33

Fig. 20. Example 2: overshoot_t1 = 0d; overhoot_t2

= 5d ................................................................. 34

Fig. 21. Block diagram of receiver circuitry .................. 35

Fig. 22. Block diagram of the active Antenna concept .. 36

Fig. 23. Overview SIGIN/SIGOUT Signal Routing ........38

Fig. 24. Sector arrangement of the EEPROM .............. 40

Fig. 25. Quartz connection ........................................... 44

Fig. 26. Internal PDown to voltage regulator logic ........47

Fig. 27. Pin RX input voltage ..................................... 103

Fig. 28. Timing for fast and standard mode devices

on the I2C-bus .............................................. 104

Fig. 29. Typical application antenna circuit diagram ... 105

Fig. 30. Package outline SOT617-1 (HVQFN32) ........108

Fig. 31. Packing information 1 tray .............................111

Fig. 32. Packing information 5 tray .............................112

Fig. 33. Tray details ....................................................113

Fig. 34. Packing information Reel .............................. 114

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Product data sheet Rev. 4.6 — 12 September 2018

COMPANY PUBLIC 227646 145 / 146

Contents

1 General description ............................................ 1

2 Features and benefits .........................................2

3 Quick reference data .......................................... 3

4 Ordering information .......................................... 4

5 Block diagram ..................................................... 5

6 Pinning information ............................................ 6

6.1 Pin description ................................................... 6

7 Functional description ........................................8

7.1 Interrupt controller ............................................. 8

7.2 Timer module ...................................................10

7.2.1 Timer modes ....................................................10

7.2.1.1 Time-Out- and Watch-Dog-Counter .................11

7.2.1.2 Wake-up timer ................................................. 11

7.2.1.3 Stop watch .......................................................11

7.2.1.4 Programmable one-shot timer ......................... 11

7.2.1.5 Periodical trigger ..............................................11

7.3 Contactless interface unit ................................ 12

7.3.1 ISO/IEC15693 functionality ..............................12

7.3.2 EPC-UID/UID-OTP functionality ...................... 13

7.3.3 ISO/IEC 18000-3 mode 3/ EPC Class-1 HF

functionality ...................................................... 13

7.3.3.1 Data encoding ICODE .....................................14

7.4 Host interfaces .................................................14

7.4.1 Host interface configuration ............................. 14

7.4.2 SPI interface .................................................... 14

7.4.2.1 General ............................................................ 15

7.4.2.2 Read data ........................................................ 15

7.4.2.3 Write data ........................................................ 15

7.4.2.4 Address byte ....................................................16

7.4.2.5 Timing Specification SPI ..................................16

7.4.3 RS232 interface ............................................... 17

7.4.3.1 Selection of the transfer speeds ...................... 17

7.4.3.2 Framing ............................................................18

7.4.4 I2C-bus interface ............................................. 19

7.4.4.1 General ............................................................ 19

7.4.4.2 I2C Data validity .............................................. 20

7.4.4.3 I2C START and STOP conditions ................... 21

7.4.4.4 I2C byte format ................................................21

7.4.4.5 I2C Acknowledge .............................................21

7.4.4.6 I2C 7-bit addressing ........................................ 22

7.4.4.7 I2C-register write access ................................. 23

7.4.4.8 I2C-register read access ................................. 23

7.4.4.9 I2CL-bus interface ........................................... 24

7.4.5 SAM interface .................................................. 25

7.4.5.1 SAM functionality .............................................25

7.4.5.2 SAM connection .............................................. 25

7.4.6 Boundary scan interface ..................................26

7.4.6.1 Interface signals .............................................. 26

7.4.6.2 Test Clock (TCK) .............................................26

7.4.6.3 Test Mode Select (TMS) ................................. 27

7.4.6.4 Test Data Input (TDI) ...................................... 27

7.4.6.5 Test Data Output (TDO) .................................. 27

7.4.6.6 Data register .................................................... 27

7.4.6.7 Boundary scan cell .......................................... 27

7.4.6.8 Boundary scan path ........................................ 28

7.4.6.9 Boundary Scan Description Language

(BSDL) ............................................................. 29

7.4.6.10 Non-IEEE1149.1 commands ........................... 29

7.5 Buffer ............................................................... 29

7.5.1 Overview .......................................................... 29

7.5.2 Accessing the FIFO buffer ...............................30

7.5.3 Controlling the FIFO buffer ..............................30

7.5.4 Status Information about the FIFO buffer ........ 30

7.6 Analog interface and contactless UART .......... 31

7.6.1 General ............................................................ 31

7.6.2 TX transmitter .................................................. 31

7.6.2.1 Overshoot protection ....................................... 33

7.6.2.2 Bit generator .................................................... 34

7.6.3 Receiver circuitry ............................................. 34

7.6.3.1 General ............................................................ 34

7.6.3.2 Block diagram ..................................................34

7.6.4 Active antenna concept ................................... 36

7.6.5 Symbol generator ............................................ 39

7.7 Memory ............................................................39

7.7.1 Memory overview .............................................39

7.7.2 EEPROM memory organization .......................39

7.7.2.1 Product information and configuration - Page

0 ....................................................................... 40

7.7.3 EEPROM initialization content LoadProtocol ... 42

7.8 Clock generation ..............................................44

7.8.1 Crystal oscillator .............................................. 44

7.8.2 IntegerN PLL clock line ................................... 44

7.8.3 Low Frequency Oscillator (LFO) ......................45

7.9 Power management .........................................46

7.9.1 Supply concept ................................................ 46

7.9.2 Power reduction mode .....................................46

7.9.2.1 Power-down ..................................................... 46

7.9.2.2 Standby mode ................................................. 46

7.9.2.3 Modem off mode ............................................. 47

7.9.3 Low-Power Card Detection (LPCD) .................47

7.9.4 Reset and start-up time ...................................47

7.10 Command set .................................................. 48

7.10.1 General ............................................................ 48

7.10.2 Command set overview ................................... 48

7.10.3 Command functionality .................................... 49

7.10.3.1 Idle command .................................................. 49

7.10.3.2 LPCD command .............................................. 49

7.10.3.3 AckReq command ........................................... 49

7.10.3.4 Receive command ...........................................49

7.10.3.5 Transmit command .......................................... 49

7.10.3.6 Transceive command ...................................... 49

7.10.3.7 WriteE2 command ........................................... 50

7.10.3.8 WriteE2PAGE command ................................. 50

7.10.3.9 ReadE2 command ...........................................50

7.10.3.10 LoadReg command ......................................... 50

7.10.3.11 LoadProtocol command ...................................50

7.10.3.12 GetRNR command .......................................... 51

7.10.3.13 SoftReset command ........................................ 52

8 SLRC610 registers ............................................ 53

8.1 Register bit behavior ....................................... 53

8.2 Command configuration ...................................56

NXP Semiconductors SLRC610

High-performance ICODE frontend SLRC610 and SLRC610 plus

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section 'Legal information'.

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 12 September 2018

Document identifier: SLRC610

Document number: 227646

8.2.1 Command ........................................................ 56

8.3 SAM configuration register .............................. 56

8.3.1 HostCtrl ............................................................ 56

8.4 FIFO configuration register .............................. 57

8.4.1 FIFOControl ..................................................... 57

8.4.2 WaterLevel .......................................................58

8.4.3 FIFOLength ......................................................58

8.4.4 FIFOData ......................................................... 59

8.5 Interrupt configuration registers ....................... 59

8.5.1 IRQ0 register ................................................... 60

8.5.2 IRQ1 register ................................................... 60

8.5.3 IRQ0En register ............................................... 61

8.5.4 IRQ1En ............................................................ 62

8.6 Contactless interface configuration registers ... 62

8.6.1 Error ................................................................. 62

8.6.2 Status ...............................................................63

8.6.3 RxBitCtrl ...........................................................64

8.6.4 RxColl .............................................................. 65

8.7 Timer configuration registers ........................... 65

8.7.1 TControl ........................................................... 65

8.7.2 T0Control ......................................................... 66

8.7.2.1 T0ReloadHi ...................................................... 67

8.7.2.2 T0ReloadLo ..................................................... 67

8.7.2.3 T0CounterValHi ............................................... 68

8.7.2.4 T0CounterValLo ...............................................68

8.7.2.5 T1Control ......................................................... 68

8.7.2.6 T1ReloadHi ...................................................... 69

8.7.2.7 T1ReloadLo ..................................................... 69

8.7.2.8 T1CounterValHi ............................................... 70

8.7.2.9 T1CounterValLo ...............................................70

8.7.2.10 T2Control ......................................................... 70

8.7.2.11 T2ReloadHi ...................................................... 71

8.7.2.12 T2ReloadLo ..................................................... 71

8.7.2.13 T2CounterValHi ............................................... 72

8.7.2.14 T2CounterValLoReg ........................................ 72

8.7.2.15 T3Control ......................................................... 72

8.7.2.16 T3ReloadHi ...................................................... 73

8.7.2.17 T3ReloadLo ..................................................... 74

8.7.2.18 T3CounterValHi ............................................... 74

8.7.2.19 T3CounterValLo ...............................................74

8.7.2.20 T4Control ......................................................... 75

8.7.2.21 T4ReloadHi ...................................................... 76

8.7.2.22 T4ReloadLo ..................................................... 76

8.7.2.23 T4CounterValHi ............................................... 76

8.7.2.24 T4CounterValLo ...............................................77

8.8 Transmitter configuration registers .................. 77

8.8.1 TxMode ............................................................ 77

8.8.2 TxAmp ..............................................................78

8.8.3 TxCon .............................................................. 78

8.8.4 Txl .................................................................... 79

8.9 CRC configuration registers .............................79

8.9.1 TxCrcPreset ..................................................... 79

8.9.2 RxCrcCon ........................................................ 80

8.10 Transmitter configuration registers .................. 81

8.10.1 TxDataNum ......................................................81

8.10.2 TxSym10BurstLen ........................................... 82

8.10.3 TxWaitCtrl ........................................................ 82

8.10.4 TxWaitLo ..........................................................83

8.11 FrameCon ........................................................ 83

8.12 Receiver configuration registers ...................... 84

8.12.1 RxSofD .............................................................84

8.12.2 RxCtrl ............................................................... 84

8.12.3 RxWait ............................................................. 85

8.12.4 RxThreshold .....................................................85

8.12.5 Rcv ...................................................................86

8.12.6 RxAna .............................................................. 86

8.13 Clock configuration .......................................... 87

8.13.1 SerialSpeed ..................................................... 87

8.13.2 LFO_Trimm ......................................................88

8.13.3 PLL_Ctrl Register ............................................ 89

8.13.4 PLLDiv_Out ......................................................90

8.14 Low-power card detection configuration

registers ........................................................... 90

8.14.1 LPCD_QMin .....................................................90

8.14.2 LPCD_QMax ....................................................91

8.14.3 LPCD_IMin .......................................................91

8.14.4 LPCD_Result_I ................................................ 92

8.14.5 LPCD_Result_Q .............................................. 92

8.14.6 LPCD_Options ................................................. 92

8.15 Pin configuration .............................................. 93

8.15.1 PinEn ............................................................... 93

8.15.2 PinOut .............................................................. 94

8.15.3 PinIn .................................................................95

8.15.4 SigOut .............................................................. 95

8.16 Version register ............................................... 96

8.16.1 Version .............................................................96

9 Limiting values .................................................. 97

10 Recommended operating conditions .............. 98

11 Thermal characteristics ....................................99

12 Characteristics ................................................ 100

12.1 Timing characteristics .................................... 103

13 Application information ..................................105

13.1 Antenna design description ........................... 105

13.1.1 EMC low pass filter ....................................... 105

13.1.2 Antenna matching ..........................................106

13.1.3 Receiving circuit .............................................106

13.1.4 Antenna coil ...................................................106

14 Package outline ...............................................108

15 Handling information ...................................... 110

16 Packing information ........................................111

17 Appendix .......................................................... 116

17.1 LoadProtocol command register initialization . 116

17.2 SLRC61003 EEPROM configuration ............. 122

18 Abbreviations .................................................. 135

19 References ....................................................... 137

20 Revision history .............................................. 138

21 Legal information ............................................ 139