Mobile Intel Pentium III
Processor in BGA2 and Micro-
PGA2 Packages
Featuring Intel® SpeedStep™ Technology at
1 GHz, 900 MHz, 850 MHz, 800 MHz, 750 MHz,
700 MHz, Low-voltage 750MHz, Low-voltage
700MHz, Low-voltage 600 MHz, Ultra Low-
voltage 600 MHz and Ultra Low-voltage 500
MHz
Datasheet
Order Number: 283653-001
R
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
2Datasheet Order Number 283653-001
Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability
whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to
fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not
intended for use in medical, life saving, or life sustaining applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for
future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.
The mobile Intel® Pentium® III processor may contain design defects or errors known as errata that may cause the product to deviate from published
specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an order number and are referenced in this document, or other Intel literature, may be obtained by calling1-800-548-
4725 or by visiting Intel’s web site at http://www.intel.com
Copyright © Intel Corporation, 1998-2001.
Intel®, Pentium® III and SpeedStep™ Technology are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States
and other countries.
* Other names and brands may be claimed as the property of others.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 3
Mobile Intel Pentium III
Processor in BGA2 and Micro-
PGA2 Packages
Product Features
n Processor core/bus speeds:
− Featuring Intel® SpeedStepTM technology:
1000/100 MHz ( Maximum Performance Mode at
1.70V) and 700/100 MHz (Battery Optimized Mode
at 1.35V)
− Featuring Intel SpeedStep technology: 900/100
MHz ( Maximum Performance Mode at 1.70V) and
700/100 MHz (Battery Optimized Mode at 1.35V)
− Featuring Intel SpeedStep technology: 850/100
MHz ( Maximum Performance Mode at 1.60V) and
700/100 MHz (Battery Optimized Mode at 1.35V)
− Featuring Intel SpeedStep technology: 800/100
MHz ( Maximum Performance Mode at 1.60V) and
650/100 MHz (Battery Optimized Mode at 1.35V)
− Featuring Intel SpeedStep technology: 750/100
MHz ( Maximum Performance Mode at 1.60V) and
600/100 MHz (Battery Optimized Mode at 1.35V)
− Featuring Intel SpeedStep technology: 700/100
MHz ( Maximum Performance Mode at 1.60V) and
550/100 MHz (Battery Optimized Mode at 1.35V)
− Featuring Intel SpeedStep technology: 750/100
MHz ( Maximum Performance Mode at 1.35V) and
500/100 MHz (Battery Optimized Mode at 1.10V)
− Featuring Intel SpeedStep technology: 700/100
MHz ( Maximum Performance Mode at 1.35V) and
500/100 MHz (Battery Optimized Mode at 1.10V)
− Featuring Intel SpeedStep technology: 600/100
MHz ( Maximum Performance Mode at 1.35V) and
500/100 MHz (Battery Optimized Mode at 1.10V)
− Featuring Intel SpeedStep technology: 600/100
MHz ( Maximum Performance Mode at 1.10V) and
300/100 MHz (Battery Optimized Mode at 0.975V)
− Featuring Intel SpeedStep technology: 500/100
MHz ( Maximum Performance Mode at 1.10V) and
300/100 MHz (Battery Optimized Mode at 0.975V)
n Supports the Intel Architecture with Dynamic
Execution
n On-die primary 16-Kbyte instruction cache and
16-Kbyte write-back data cache
n On-die second level cache (256-Kbyte)
n Integrated GTL+ termination
n Integrated math co-processor
n Intel Processor Serial Number
n BGA2 and Micro-PGA2 packaging technologies
— Supports thin form factor notebook designs
— Exposed die enables more efficient heat
dissipation
— Ultra Low Voltage (ULV=1.10V/ 0.975V)
and Low Voltage (LV=1.35V/ 1.10V) mobile
Intel Pentium III processors are only
available in BGA2 packages.
n Fully compatible with previous Intel
microprocessors
— Binary compatible with all applications
— Support for MMX™ technology
— Support for Streaming SIMD Extensions
n Power Management Features
— Quick Start and Deep Sleep modes
provide low power dissipation
n On-die thermal diode
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
4Datasheet Order Number 283653-001
Contents
1. Introduction............................................................................................................................................. 9
1.1 Overview..................................................................................................................... 12
1.2 Terminology ................................................................................................................ 12
1.3 References.................................................................................................................. 13
2. Mobile Pentium III Processor Features................................................................................................. 14
2.1 New Features in the Mobile Pentium III Processor ........................................................ 14
2.1.1 On-die GTL+ Termination............................................................................... 14
2.1.2 Streaming SIMD Extensions........................................................................... 14
2.1.3 Intel SpeedStep Technology........................................................................... 14
2.1.4 Signal Differences Between the Mobile Pentium II Processor and the Mobile
Pentium III Processor ..................................................................................... 14
2.2 Power Management..................................................................................................... 15
2.2.1 Clock Control Architecture.............................................................................. 15
2.2.2 Normal State.................................................................................................. 15
2.2.3 Auto Halt State............................................................................................... 15
2.2.4 Stop Grant State............................................................................................ 16
2.2.5 Quick Start State............................................................................................ 17
2.2.6 HALT/Grant Snoop State................................................................................ 17
2.2.7 Sleep State.................................................................................................... 17
2.2.8 Deep Sleep State........................................................................................... 18
2.2.9 Operating System Implications of Low-power States........................................ 18
2.2.10 Intel SpeedStep Technology........................................................................... 18
2.3 GTL+ Signals .............................................................................................................. 19
2.4 Mobile Pentium III Processor CPUID............................................................................ 19
3. Electrical Specifications ....................................................................................................................... 20
3.1 Processor System Signals............................................................................................ 20
3.1.1 Power Sequencing Requirements................................................................... 21
3.1.2 Test Access Port (TAP) Connection................................................................ 21
3.1.3 Catastrophic Thermal Protection..................................................................... 22
3.1.4 Unused Signals.............................................................................................. 22
3.1.5 Signal State in Low-power States.................................................................... 22
3.1.5.1 System Bus Signals .................................................................... 22
3.1.5.2 CMOS and Open-drain Signals.................................................... 22
3.1.5.3 Other Signals.............................................................................. 23
3.2 Power Supply Requirements........................................................................................ 23
3.2.1 Decoupling Recommendations....................................................................... 23
3.2.2 Voltage Planes............................................................................................... 23
3.3 System Bus Clock and Processor Clocking................................................................... 24
3.4 Intel SpeedStep Technology ........................................................................................ 24
3.5 Maximum Ratings........................................................................................................ 25
3.6 DC Specifications ........................................................................................................ 25
3.7 AC Specifications......................................................................................................... 29
3.7.1 System Bus, Clock, APIC, TAP, CMOS, and Open-drain AC Specifications...... 29
4. System Signal Simulations................................................................................................................... 41
4.1 System Bus Clock (BCLK) and PICCLK AC Signal Quality Specifications ...................... 41
4.2 GTL+ AC Signal Quality Specifications......................................................................... 42
4.3 Non-GTL+ Signal Quality Specifications ....................................................................... 44
4.3.1 PWRGOOD Signal Quality Specifications ....................................................... 45
5. Mechanical Specifications.................................................................................................................... 46
5.1 Surface-mount BGA2 Package Dimensions.................................................................. 46
5.2 Socketable Micro-PGA2 Package Dimensions.............................................................. 48
5.3 Signal Listings............................................................................................................. 51
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 5
6. Thermal Specifications ......................................................................................................................... 59
6.1 Thermal Diode............................................................................................................. 61
7. Processor Initialization and Configuration........................................................................................... 62
7.1 Description.................................................................................................................. 62
7.1.1 Quick Start Enable......................................................................................... 62
7.1.2 System Bus Frequency .................................................................................. 62
7.1.3 APIC Enable.................................................................................................. 62
7.2 Clock Frequencies and Ratios...................................................................................... 62
8. Processor Interface............................................................................................................................... 63
8.1 Alphabetical Signal Reference...................................................................................... 63
8.2 Signal Summaries........................................................................................................ 74
Appendix A: PLL RLC Filter Specification ......................................................................................................... 77
A.1 Introduction ................................................................................................................. 77
A.2 Filter Specification ...................................................................................................... 77
A.3 Recommendation for Mobile Systems........................................................................... 79
A.4 Comments................................................................................................................... 79
Appendix B: Intel Mobile Voltage Positioning (IMVP) for the Mobile Pentium III Processor.............................. 81
B.1 Introduction ................................................................................................................. 81
B.2 Reference Documents ................................................................................................. 81
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
6Datasheet Order Number 283653-001
Figures Figure 1. Signal Groups of a Mobile Pentium III Processor/440BX AGPset - Based System ......... 10
Figure 2. Signal Groups of a Mobile Pentium III Processor/440MX Chipset - Based System......... 11
Figure 3. Clock Control States.................................................................................................... 16
Figure 4. Vcc Ramp Rate Requirement...................................................................................... 21
Figure 5. PLL RLC Filter............................................................................................................ 24
Figure 6. PICCLK/TCK Clock Timing Waveform ......................................................................... 35
Figure 7. BCLK Timing Waveform.............................................................................................. 35
Figure 8. Valid Delay Timings .................................................................................................... 36
Figure 9. Setup and Hold Timings.............................................................................................. 36
Figure 10. Cold/Warm Reset and Configuration Timings............................................................. 37
Figure 11. Power-on Reset Timings ........................................................................................... 37
Figure 12. Test Timings (Boundary Scan)................................................................................... 38
Figure 13. Test Reset Timings................................................................................................... 39
Figure 14. Quick Start/Deep Sleep Timing.................................................................................. 39
Figure 15. Stop Grant/Sleep/Deep Sleep Timing......................................................................... 40
Figure 16. Intel SpeedStep Technology/Deep Sleep Timing........................................................ 40
Figure 17. BCLK/PICCLK Generic Clock Waveform.................................................................... 42
Figure 18. Low to High, GTL+ Receiver Ringback Tolerance....................................................... 43
Figure 19. High to Low, GTL+ Receiver Ringback Tolerance....................................................... 43
Figure 20. Maximum Acceptable Overshoot/Undershoot Waveform............................................. 44
Figure 21. Surface-mount BGA2 Package - Top and Side View................................................... 47
Figure 22. Surface-mount BGA2 Package - Bottom View............................................................ 48
Figure 23. Socketable Micro-PGA2 Package - Top and Side View............................................... 50
Figure 24. Socketable Micro-PGA2 Package - Bottom View........................................................ 51
Figure 25. Pin/Ball Map - Top View ............................................................................................ 52
Figure 26. PWRGOOD Relationship at Power On....................................................................... 70
Figure 27. PLL Filter Specifications............................................................................................ 78
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 7
Tables Table 1. New Mobile Pentium III Processor Signals .................................................................... 14
Table 2. Removed Mobile Pentium II Processor Signals.............................................................. 14
Table 3. Clock State Characteristics........................................................................................... 18
Table 4. Mobile Pentium III Processor CPUID............................................................................. 19
Table 5. Mobile Pentium III Processor CPUID Cache and TLB Descriptors.................................. 19
Table 6. System Signal Groups.................................................................................................. 20
Table 7. Recommended Resistors for Mobile Pentium III Processor Signals................................ 20
Table 8. Mobile Pentium III Processor Absolute Maximum Ratings.............................................. 25
Table 9A. Mobile Pentium III Processor DC Specifications.......................................................... 26
Table 9B. Mobile Pentium III Processor DC Specifications.......................................................... 26
Table 10. GTL+ Signal Group DC Specifications......................................................................... 27
Table 11. GTL+ Bus DC Specifications....................................................................................... 27
Table 12. Clock, APIC, TAP, CMOS, and Open-drain Signal Group DC Specifications................. 28
Table 13. System Bus Clock AC Specifications........................................................................... 29
Table 14. Valid Mobile Pentium III Processor Frequencies........................................................... 30
Table 15. GTL+ Signal Groups AC Specifications....................................................................... 30
Table 16. CMOS and Open-drain Signal Groups AC Specifications............................................. 31
Table 17. Reset Configuration AC Specifications........................................................................ 31
Table 18. APIC Bus Signal AC Specifications............................................................................. 32
Table 19. TAP Signal AC Specifications..................................................................................... 33
Table 20. Quick Start/Deep Sleep AC Specifications................................................................... 33
Table 21. Stop Grant/Sleep/Deep Sleep AC Specifications ......................................................... 34
Table 22. Intel SpeedStep Technology AC Specifications............................................................ 34
Table 23. BCLK Signal Quality Specifications............................................................................. 41
Table 24. PICCLK Signal Quality Specifications.......................................................................... 41
Table 25. GTL+ Signal Group Ringback Specification................................................................. 42
Table 26. GTL+ Signal Group Overshoot/Undershoot Tolerance at the Processor Core.44
Table 27. Non-GTL+ Signal Group Overshoot/Undershoot Tolerance at the Processor Core ....... 45
Table 28. Surface-mount BGA2 Package Specifications ............................................................. 46
Table 29. Socketable Micro-PGA2 Package Specification........................................................... 49
Table 30. Signal Listing in Order by Pin/Ball Number.................................................................. 52
Table 31. Signal Listing in Order by Signal Name ....................................................................... 55
Table 32. Voltage and No-Connect Pin/Ball Locations................................................................. 58
Table 33. Power Specifications for Mobile Pentium III Processor with Intel SpeedStep Technology60
Table 34. Thermal Diode Interface ............................................................................................. 61
Table 35. Thermal Diode Specifications...................................................................................... 61
Table 36. BSEL[1:0] Encoding................................................................................................... 65
Table 37. Voltage Identification Encoding................................................................................... 74
Table 38. Input Signals.............................................................................................................. 74
Table 39. Output Signals ........................................................................................................... 75
Table 40. Input/Output Signals (Single Driver)............................................................................ 75
Table 41. Input/Output Signals (Multiple Driver).......................................................................... 76
Table 42. PLL Filter Inductor Recommendations......................................................................... 79
Table 43. PLL Filter Capacitor Recommendations ...................................................................... 79
Table 44. PLL Filter Resistor Recommendations......................................................................... 79
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
8Datasheet Order Number 283653-001
Revision History
Date Revision
Number Updates
April 2000 1.0 Initial release
June 2000 2.0 Revision 2.0 updates include:
• Added new processor speed 750/600 MHz
• Added new Low Voltage processor speed 600/500 MHz
• Updated references
September 2000 3.0 Revision 3.0 updates include:
• Added new processor speed 850/700 MHz, 800/650 MHz
• Updated references
January 2001 4.0 Revision 4.0 updates include:
• Added new Ultra Low Voltage processor speed 500/300 MHz
• Updated references
• Corrected die width size for C-step in Table 28
• Updated the decoupling recommendations in Section 3.2.1
• Updated the Pin/Ball P1 connection guideline in Section 5.3
February 2001 5.0 Revision 5.0 updates include:
• Added new Low Voltage processor speed 700/500 MHz
• Updated references
• Updated current specifications in Table 9 and power specifications in Table
33
March 2001 6.0 Revision 6.0 updates include:
• Added new processor speed 900/700 MHz and 1GHz/700 MHz
• Updated references
• Updated current specifications in Table 9 and power specifications in Table
33
• Updated die width and length size in table 28
• Updated die width and length size in table 29
May 2001 7.0 Revision 7.0 updates include:
• Added new Low Voltage 750/500 MHz and Ultra Low Voltage 600/300 MHz
processor speeds
• Added new 1GHz/700 MHz at Tj=92°C power specification in
Table 33
• Reformatted Table 9 to Table 9A and Table 9B. Table 9B shows battery
optimized mode current specifications.
• Updated references
• Updated current specifications in Table 9B and power specifications in
Table 33
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 9
1. Introduction
Using Intel’s advanced 0.18 micron process technology, the mobile Intel® Pentium® III processor
offers high performance and lower power consumption. Key Performance advancements include
the addition of new Internet Streaming SIMD instructions, an advanced transfer cache
architecture, and a processor system bus speed of 100 MHz. These features are offered in BGA2
and micro-PGA2 packages that are up to 20% smaller than those offered for the mobile Intel
Pentium II processor. All of these technologies make outstanding performance possible for
mobile PCs in a variety of shapes and sizes.
The mobile Intel Pentium III processor featuring Intel SpeedStep™ technology is the next dramatic
step towards achieving near desktop performance. This exciting new processor has two
performance modes and allows real-time dynamic switching of the voltage and frequency between
the modes. This occurs by switching the bus ratios, core operating voltage, and core processor
speeds without resetting the system.
The integrated L2 cache is designed to help improve performance, and it complements the system
bus by providing critical data faster and reducing total system power consumption. The mobile
Pentium III processor’s 64-bit wide Gunning Transceiver Logic (GTL+) system bus provides a
glue-less, point-to-point interface for an I/O bridge/memory controller, and is compatible with the
440BX AGPset, 815EM, 440ZX-M AGPset, and the 440MX Chipset.
Figure 1 shows the various parts of a mobile Pentium III processor/440BX or 440ZX-M AGPset –
based system and how the mobile Pentium III processor connects to them.
Figure 2 shows an alternative mobile Pentium III processor/440MX Chipset - based system.
This document covers the electrical, mechanical, and thermal specifications for the mobile
Pentium III processor featuring Intel SpeedStep technology at the following frequencies: 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz and 700 MHz in BGA2 and micro-PGA2 packages,
low voltage 750 MHz, low voltage 700 MHz, low voltage 600 MHz, ultra low voltage 600 MHz,
and ultra low voltage 500 MHz in BGA2 packages.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
10 Datasheet Order Number 283653-001
Figure 1. Signal Groups of a Mobile Pentium III Processor/440BX AGPset - Based System
Mobile
Pentium
®
III
Processor
443BX
OR
440ZX-M
North Bridge
PIIX4E
South Bridge
PCI
IOAPIC
(optional)
ISA/EIO
TAP
APIC
Bus
DRAM
System
Bus
Thermal
Sensor
System
Controller
V0000-03
OR
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 11
Figure 2. Signal Groups of a Mobile Pentium III Processor/440MX Chipset - Based System
Mobile
Pentium® III
Processor
440MX
PCIset
PCIX-bus
TAP
DRAM
System
Bus
Thermal
Sensor
SMBus
System
Controller V0000-04
OR
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
12 Datasheet Order Number 283653-001
1.1 Overview
Performance improved over existing mobile processors
— Supports the Intel Architecture with Dynamic Execution
— Supports the Intel Architecture MMX™ technology
— Supports Streaming SIMD Extensions for enhanced video, sound, and 3D performance
— Supports Intel SpeedStep Technology
— Integrated Intel Floating Point Unit compatible with the IEEE 754 standard
On-die primary (L1) instruction and data caches
— 4-way set associative, 32-byte line size, 1 line per sector
— 16-Kbyte instruction cache and 16-Kbyte write-back data cache
— Cacheable range controlled by processor programmable registers
On-die second level (L2) cache
— 8-way set associative, 32-byte line size, 1 line per sector
— Operates at full core speed
— 256-Kbyte, ECC protected cache data array
GTL+ system bus interface
— 64-bit data bus, 100-MHz operation
— Uniprocessor, two loads only (processor and I/O bridge/memory controller)
— Integrated termination
Pentium II processor clock control
— Quick Start for low power, low exit latency clock “throttling”
— Deep Sleep mode for lower power dissipation
Thermal diode for measuring processor temperature
1.2 Terminology
In this document a “#” symbol following a signal name indicates that the signal is active low. This
means that when the signal is asserted (based on the name of the signal) it is in an electrical low
state. Otherwise, signals are driven in an electrical high state when they are asserted. In state
machine diagrams, a signal name in a condition indicates the condition of that signal being
asserted. If the signal name is preceded by a “!” symbol, then it indicates the condition of that
signal not being asserted. For example, the condition “!STPCLK# and HS” is equivalent to “the
active low signal STPCLK# is unasserted (i.e., it is at 1.5V) and the HS condition is true.” The
symbols “L” and “H” refer respectively to electrical low and electrical high signal levels. The
symbols “0” and “1” refer respectively to logical low and logical high signal levels. For example,
BD[3:0] = “1010” = “HLHL” refers to a hexadecimal “A,” and D[3:0]# = “1010” = “LHLH” also
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 13
refers to a hexadecimal “A.” The symbol “X” refers to a “Don’t Care” condition, where a “0” or a
“1” results in the same behavior.
1.3 References
Pentium® III Processor at 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 600 MHz, and
Ultra Low-voltage 500 MHz Datasheet (Order Number 249562-001)
Mobile Pentium® III Processor I/O Buffer Models, IBIS Format (Available in electronic form;
Contact your Intel Field Sales Representative)
Mobile Pentium® III Processor GTL+ System Bus Layout Guideline (Contact your Intel Field Sales
Representative)
Mobile Pentium® II Processor in Micro-PGA and BGA Packages at 400 MHz, 366 MHz, 333 MHz,
300 PE MHz and 266 PE MHz Datasheet (Order Number 245103-003)
Mobile Pentium® II Processor in Mini Cartridge at 400 MHz, 366 MHz, 333 MHz, 300 PE MHz
and 266 PE MHz Datasheet (Order Number 245108-002)
P6 Family of Processors Hardware Developer’s Manual (Order Number 244001-001)
CK97 Clock Driver Specification (Contact your Intel Field Sales Representative)
Intel® Architecture Optimization Manual (Order Number 242816-003)
Intel® Architecture Software Developer’s Manual Volume I: Basic Architecture (Order Number
243190)
Intel® Architecture Software Developer’s Manual Volume II: Instruction Set Reference (Order
Number 243191)
Intel® Architecture Software Developer’s Manual Volume III: System Programming Guide (Order
Number 243192)
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
14 Datasheet Order Number 283653-001
2. Mobile Pentium III Processor Features
2.1 New Features in the Mobile Pentium III Processor
2.1.1 On-die GTL+ Termination
The termination resistors for the GTL+ system bus are integrated onto the processor die. The
RESET# signal does not have on-die termination and requires an external 56.2Ω ±1% terminating
resistor.
2.1.2 Streaming SIMD Extensions
The mobile Pentium III processor is the first mobile processor to implement Streaming SIMD
(single instruction, multiple data) extensions. Streaming SIMD extensions can enhance floating
point, video, sound, and 3-D application performance.
2.1.3 Intel SpeedStep Technology
Intel SpeedStep technology is a new mobile feature developed by Intel. The mobile Pentium III
processors that are enabled with Intel SpeedStep technology have the ability to switch between
two bus ratios and core speeds without having to reset the processor.
2.1.4 Signal Differences Between the Mobile Pentium II Processor and
the Mobile Pentium III Processor
With the exception of BCLK, PICCLK, and PWRGOOD, the CMOS inputs and Open-drain
outputs have changed from 2.5V tolerant, as on the mobile Pentium II processor to 1.5V tolerant.
Table 1. New Mobile Pentium III Processor Signals
Signals Function
CLKREF System bus clock trip point control
CMOSREF 1.5V CMOS input buffer trip point control
EDGECTRLP GTL+ output buffer control
GHI# Intel SpeedStep technology operating mode selection
BSEL[1:0] Processor system bus speed selection
RSVD Reserved, may be defined in the future
RTTIMPEDP On-die GTL+ termination control
VCCT On-die GTL+ termination current supply
VID[4:0] Voltage Identification
Table 2. Removed Mobile Pentium II Processor Signals
Signals Purpose
EDGECTRLN GTL+ output buffer control
BSEL 100/66 MHz processor system bus speed selection
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 15
2.2 Power Management
2.2.1 Clock Control Architecture
The mobile Pentium III processor clock control architecture (Figure 3) has been optimized for
leading edge deep green desktop and mobile computer designs. The clock control architecture
consists of seven different clock states: Normal, Stop Grant, Auto Halt, Quick Start, HALT/Grant
Snoop, Sleep, and Deep Sleep states. The Auto Halt state provides a low-power clock state that
can be controlled through the software execution of the HLT instruction. The Quick Start state
provides a very low power and low exit latency clock state that can be used for hardware
controlled “idle” computer states. The Deep Sleep state provides an extremely low-power state
that can be used for “Power-On-Suspend” computer states, which is an alternative to shutting off
the processor’s power. Compared to the Pentium processor exit latency of 1 msec, the exit latency
of the Deep Sleep state has been reduced to 30 µsec in the mobile Pentium III processor. The Stop
Grant and Sleep states shown in Figure 3 are intended for use in “Deep Green” desktop and server
systems — not in mobile systems. Performing state transitions not shown in Figure 3 is neither
recommended nor supported.
The Stop Grant and Quick Start clock states are mutually exclusive, i.e., a strapping option on
signal A15# chooses which state is entered when the STPCLK# signal is asserted. The Quick Start
state is enabled by strapping the A15# signal to ground at Reset; otherwise, asserting the
STPCLK# signal puts the processor into the Stop Grant state. The Stop Grant state has a higher
power level than the Quick Start state and is designed for Symmetric Multi-Processing (SMP)
platforms. The Quick Start state has a much lower power level, but it can only be used in
uniprocessor platforms. Table 3 provides clock state characteristics, which are described in detail
in the following sections.
2.2.2 Normal State
The Normal state of the processor is the normal operating mode where the processor’s core clock
is running and the processor is actively executing instructions.
2.2.3 Auto Halt State
This is a low-power mode entered by the processor through the execution of the HLT instruction.
The power level of this mode is similar to the Stop Grant state. A transition to the Normal state is
made by a halt break event (one of the following signals going active: NMI, INTR, BINIT#,
INIT#, RESET#, FLUSH#, or SMI#).
Asserting the STPCLK# signal while in the Auto Halt state will cause the processor to transition
to the Stop Grant or Quick Start state, where a Stop Grant Acknowledge bus cycle will be issued.
Deasserting STPCLK# will cause the processor to return to the Auto Halt state without issuing a
new Halt bus cycle.
The SMI# interrupt is recognized in the Auto Halt state. The return from the System Management
Interrupt (SMI) handler can be to either the Normal state or the Auto Halt state. See the Intel®
Architecture Software Developer’s Manual, Volume III: System Programmer’s Guide for more
information. No Halt bus cycle is issued when returning to the Auto Halt state from the System
Management Mode (SMM).
The FLUSH# signal is serviced in the Auto Halt state. After the on-chip and off-chip caches have
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
16 Datasheet Order Number 283653-001
been flushed, the processor will return to the Auto Halt state without issuing a Halt bus cycle.
Transitions in the A20M# and PREQ# signals are recognized while in the Auto Halt state.
Figure 3. Clock Control States
HALT/Grant
Snoop
Normal
HS=false
Stop
Grant
Auto
Halt
HS=true
Quick
Start
Sleep
Deep
Sleep
(!STPCLK#
and !HS) or
stop break
STPCLK# and
!QSE and SGA
Snoop
occurs
Snoop
serviced
STPCLK# and
QSE and SGA
(!STPCLK# and !HS)
or RESET#
Snoop
serviced Snoop
occurs
!STPCLK#
and HS
STPCLK# and
!QSE and SGA
HLT and
halt bus cycle
halt
break
Snoop
serviced
Snoop
occurs
STPCLK# and
QSE and SGA
!STPCLK#
and HS
!SLP# or
RESET#
SLP#
BCLK
stopped
BCLK on
and !QSE
BCLK
stopped
BCLK on
and QSE
V0001-00
NOTES: halt break – A20M#, BINIT#, FLUSH#, INIT#, INTR, NMI, PREQ#, RESET#, SMI#
HLT – HLT instruction executed
HS – Processor Halt State
QSE – Quick Start State Enabled
SGA – Stop Grant Acknowledge bus cycle issued
stop break – BINIT#, RESET#
2.2.4 Stop Grant State
The processor enters this mode with the assertion of the STPCLK# signal when it is configured for
Stop Grant state (via the A15# strapping option). The processor is still able to respond to snoop
requests and latch interrupts. Latched interrupts will be serviced when the processor returns to the
Normal state. Only one occurrence of each interrupt event will be latched. A transition back to the
Normal state can be made by the deassertion of the STPCLK# signal or the occurrence of a stop
break event (a BINIT# or RESET# assertion).
The processor will return to the Stop Grant state after the completion of a BINIT# bus
initialization unless STPCLK# has been de-asserted. RESET# assertion will cause the processor to
immediately initialize itself, but the processor will stay in the Stop Grant state after initialization
until STPCLK# is deasserted. A transition to the Sleep state can be made by the assertion of the
SLP# signal.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 17
While in the Stop Grant state, assertions of FLUSH#, SMI#, INIT#, INTR, and NMI (or
LINT[1:0]) will be latched by the processor. These latched events will not be serviced until the
processor returns to the Normal state. Only one of each event will be recognized upon return to the
Normal state.
2.2.5 Quick Start State
This is a mode entered by the processor with the assertion of the STPCLK# signal when it is
configured for the Quick Start state (via the A15# strapping option). In the Quick Start state the
processor is only capable of acting on snoop transactions generated by the system bus priority
device. Because of its snooping behavior, Quick Start can only be used in a uniprocessor (UP)
configuration.
A transition to the Deep Sleep state can be made by stopping the clock input to the processor. A
transition back to the Normal state (from the Quick Start state) is made only if the STPCLK#
signal is deasserted.
While in this state the processor is limited in its ability to respond to input. It is incapable of
latching any interrupts, servicing snoop transactions from symmetric bus masters or responding to
FLUSH# or BINIT# assertions. While the processor is in the Quick Start state, it will not respond
properly to any input signal other than STPCLK#, RESET#, or BPRI#. If any other input signal
changes, then the behavior of the processor will be unpredictable. No serial interrupt messages
may begin or be in progress while the processor is in the Quick Start state.
RESET# assertion will cause the processor to immediately initialize itself, but the processor will
stay in the Quick Start state after initialization until STPCLK# is deasserted.
2.2.6 HALT/Grant Snoop State
The processor will respond to snoop transactions on the system bus while in the Auto Halt, Stop
Grant, or Quick Start state. When a snoop transaction is presented on the system bus the processor
will enter the HALT/Grant Snoop state. The processor will remain in this state until the snoop has
been serviced and the system bus is quiet. After the snoop has been serviced, the processor will
return to its previous state. If the HALT/Grant Snoop state is entered from the Quick Start state,
then the input signal restrictions of the Quick Start state still apply in the HALT/Grant Snoop
state, except for those signal transitions that are required to perform the snoop.
2.2.7 Sleep State
The Sleep state is a very low-power state in which the processor maintains its context and the
phase-locked loop (PLL) maintains phase lock. The Sleep state can only be entered from the Stop
Grant state. After entering the Stop Grant state, the SLP# signal can be asserted, causing the
processor to enter the Sleep state. The SLP# signal is not recognized in the Normal or Auto Halt
states.
The processor can be reset by the RESET# signal while in the Sleep state. If RESET# is driven
active while the processor is in the Sleep state then SLP# and STPCLK# must immediately be
driven inactive to ensure that the processor correctly initializes itself.
Input signals (other than RESET#) may not change while the processor is in the Sleep state or
transitioning into or out of the Sleep state. Input signal changes at these times will cause
unpredictable behavior. Thus, the processor is incapable of snooping or latching any events in the
Sleep state.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
18 Datasheet Order Number 283653-001
While in the Sleep state, the processor can enter its lowest power state, the Deep Sleep state.
Removing the processor’s input clock puts the processor in the Deep Sleep state. PICCLK may be
removed in the Sleep state.
2.2.8 Deep Sleep State
The Deep Sleep state is the lowest power mode the processor can enter while maintaining its
context. The Deep Sleep state is entered by stopping the BCLK input to the processor, while it is
in the Sleep or Quick Start state. For proper operation, the BCLK input should be stopped in the
Low state.
The processor will return to the Sleep or Quick Start state from the Deep Sleep state when the
BCLK input is restarted. Due to the PLL lock latency, there is a delay of up to 30 µsec after the
clocks have started before this state transition happens. PICCLK may be removed in the Deep
Sleep state. PICCLK should be designed to turn on when BCLK turns on when transitioning out of
the Deep Sleep state.
The input signal restrictions for the Deep Sleep state are the same as for the Sleep state, except
that RESET# assertion will result in unpredictable behavior.
Table 3. Clock State Characteristics
Clock State Exit Latency Snooping? System Uses
Normal N/A Yes Normal program execution
Auto Halt Approximately 10 bus clocks Yes S/W controlled entry idle mode
Stop Grant 10 bus clocks Yes H/W controlled entry/exit mobile throttling
Quick Start Through snoop, to HALT/Grant
Snoop state: immediate
Through STPCLK#, to Normal
state: 8 bus clocks
Yes H/W controlled entry/exit mobile throttling
HALT/Grant
Snoop A few bus clocks after the end of
snoop activity Yes Supports snooping in the low power states
Sleep To Stop Grant state 10 bus clocks No H/W controlled entry/exit desktop idle mode
support
Deep Sleep 30 µsec No H/W controlled entry/exit mobile powered-on
suspend support
NOTE: See Table 33 for power dissipation in the low-power states.
2.2.9 Operating System Implications of Low-power States
There are a number of architectural features of the mobile Pentium III processor that do not
function in the Quick Start or Sleep state as they do in the Stop Grant state. The time-stamp
counter and the performance monitor counters are not guaranteed to count in the Quick Start or
Sleep states. The local APIC timer and performance monitor counter interrupts should be disabled
before entering the Deep Sleep state or the resulting behavior will be unpredictable.
2.2.10 Intel SpeedStep Technology
Some mobile Pentium III processors will be offered with Intel SpeedStep technology. The Intel
SpeedStep technology allows the processor switch between two core frequencies without having
to reset the processor or change the system bus frequency. The processor has two bus ratios
programmed into it instead of one and the GHI# signal controls which one is used. After reset, the
processor will start in the lower of its two core frequencies, the “Battery Optimized” mode. An
operating mode transition to the high core frequency can be made by putting the processor into the
Deep Sleep state, raising the core voltage, setting GHI# low, and returning to the Normal state.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 19
This puts the processor into the “Maximum performance” mode. A transitioning back to the low-
core frequency can be made by reversing these steps. Refer to the Geyserville Hardware Technical
Specification and the Geyserville Software Architecture Specification for more information on
Intel SpeedStep technology.
2.3 GTL+ Signals
The mobile Pentium III processor system bus signals use a variation of the low-voltage swing GTL
signaling technology. The mobile Pentium III processor system bus specification is similar to the
Pentium II processor system bus specification, which is a version of GTL with enhanced noise
margins and less ringing.
The GTL+ system bus depends on incident wave switching and uses flight time for timing
calculations of the GTL+ signals, as opposed to capacitive derating. Analog signal simulation of
the system bus including trace lengths is highly recommended. Contact your field sales
representative to receive the IBIS models for the mobile Pentium III processor.
The GTL+ system bus of the Pentium II processor was designed to support high-speed data
transfers with multiple loads on a long bus that behaves like a transmission line. However, in
mobile systems the system bus only has two loads (the processor and the chipset) and the bus
traces are short. It is possible to change the layout and termination of the system bus to take
advantage of the mobile environment using the same GTL+ I/O buffers. In mobile systems the
GTL+ system bus is terminated at one end only. This termination is provided on the processor
core (except for the RESET# signal). Refer to the Mobile Coppermine Processor GTL+ System
Bus Layout Guideline for details on laying out the GTL+ system bus.
2.4 Mobile Pentium III Processor CPUID
The CPUID instruction does not distinguish between the Pentium III processor and the mobile
Pentium III processor. After a power-on RESET or when the CPUID version information is loaded,
the EAX register contains the values shown in
Table 4. After the L2 cache is initialized, the CPUID cache/TLB descriptors will be the values
shown in Table 5.
Table 4. Mobile Pentium III Processor CPUID
EAX[31:0] EBX[7:0]
Reserved [31:14] Type [13:12] Family [11:8] Model [7:4] Stepping [3:0] Brand ID
X0 6 8 X02
Table 5. Mobile Pentium III Processor CPUID Cache and TLB Descriptors
Cache and TLB Descriptors 01H, 02H, 03H, 04H, 08H, 0CH, 82H
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
20 Datasheet Order Number 283653-001
3. Electrical Specifications
3.1 Processor System Signals
Table 6 lists the processor system signals by type. All GTL+ signals are synchronous with the
BCLK signal. All TAP signals are synchronous with the TCK signal except TRST#. All CMOS
input signals can be applied asynchronously.
Table 6. System Signal Groups
Group Name Signals
GTL+ Input BPRI#, DEFER#, RESET#, RS[2:0]#, RSP#, TRDY#
GTL+ Output PRDY#
GTL+ I/O A[35:3]#, ADS#, AERR#, AP[1:0]#, BERR#, BINIT#, BNR#, BP[3:2]#, BPM[1:0]#,
BREQ0#, D[63:0]#, DBSY#, DEP[7:0]#, DRDY#, HIT#, HITM#, LOCK#, REQ[4:0]#, RP#
1.5V CMOS Input 2A20M#, FLUSH#, GHI#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, PREQ#, SLP#, SMI#,
STPCLK#
2.5V CMOS Input 1, 3 PWRGOOD
1.5V Open Drain Output 2FERR#, IERR#
3.3V CMOS Input4BSEL[1:0]
Clock 3BCLK
APIC Clock 3PICCLK
APIC I/O 2PICD[1:0]
Thermal Diode THERMDA, THERMDC
TAP Input 2TCK, TDI, TMS, TRST#
TAP Output 2TDO
Power/Other 5CLKREF, CMOSREF, EDGECTRLP, NC, PLL1, PLL2, RSVD, RTTIMPEDP, TESTHI,
TESTLO[2:1], VCC, VCCT, VID[4:0], VREF, VSS
NOTES:
1. See Section 8.1 for information on the PWRGOOD signal.
2. These signals are tolerant to 1.5V only. See Table 7 for the recommended pull-up resistor.
3. These signals are tolerant to 2.5V only. See Table 7 for the recommended pull-up resistor.
4. These signals are tolerant to 3.3V only. See Table 7 for the recommended pull-up resistor.
5. VCC is the power supply for the core logic.
PLL1 and PLL2 are the power supply for the PLL analog section.
VCCT is the power supply for the system bus buffers.
VREF is the voltage reference for the GTL+ input buffers.
VSS is system ground.
The CMOS, APIC, and TAP inputs can be driven from ground to 1.5V. BCLK, PICCLK, and
PWRGOOD can be driven from ground to 2.5V. The APIC data and TAP outputs are Open-drain
and should be pulled up to 1.5V using resistors with the values shown in Table 7. If Open-drain
drivers are used for input signals, then they should also be pulled up to the appropriate voltage
using resistors with the values shown in Table 7.
Table 7. Recommended Resistors for Mobile Pentium III Processor Signals
Recommended
Resistor Value (ΩΩ)Mobile Pentium III Processor Signal 1, 2
No pull-up GHI# 3
10 pull-down BREQ0#4
56.2 pull-up RESET#5
150 pull-up PICD[1:0], TDI, TDO
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 21
270 pull-up SMI#
680 pull-up STPCLK#
1K pull-up INIT#, TCK, TMS
1K pull-down TRST#
1.5K pull-up A20M#, FERR#, FLUSH#, IERR#, IGNNE#, LINT0/INTR, LINT1/NMI,
PREQ#, PWRGOOD, SLP#
NOTES:
1. The recommendations above are only for signals that are being used. These recommendations are maximum values
only; stronger pull-ups may be used. Pull-ups for the signals driven by the chipset should not violate the chipset
specification. Refer to Section 3.1.4 for the required pull-up or pull-down resistors for signals that are not being used.
2. Open-drain signals must never violate the undershoot specification in Section 4.3. Use stronger pull-ups if there is too
much undershoot.
3. GHI# has an on-die pull-up to VCCT.
4. A pull-down on BREQ0# is an alternative to having the central agent to drive BREQ0# low at reset.
5. A 56.2Ω 1% terminating resistor connected to VCCT is required.
3.1.1 Power Sequencing Requirements
The mobile Pentium III processor has no power sequencing requirements. Intel recommends that
all of the processor power planes rise to their specified values within one second of each other.
The VCC power plane must not rise too fast. At least 200 µsec (TR) must pass from the time that
VCC is at 10% of its nominal value until the time that VCC is at 90% of its nominal value (see
Figure 4).
Figure 4. Vcc Ramp Rate Requirement
Vcc
Volts
90% Vcc (nominal)
10% Vcc (nominal)
TR
Time
3.1.2 Test Access Port (TAP) Connection
The TAP interface is an implementation of the IEEE 1149.1 (“JTAG”) standard. Due to the
voltage levels supported by the TAP interface, Intel recommends that the mobile Pentium III
processor and the other 1.5-V JTAG specification compliant devices be last in the JTAG chain
after any devices with 3.3-V or 5.0-V JTAG interfaces within the system. A translation buffer
should be used to reduce the TDO output voltage of the last 3.3/5.0V device down to the 1.5V
range that the mobile Pentium III processor can tolerate. Multiple copies of TMS and TRST# must
be provided, one for each voltage level.
A Debug Port and connector may be placed at the start and end of the JTAG chain containing the
processor, with TDI to the first component coming from the Debug Port and TDO from the last
component going to the Debug Port. There are no requirements for placing the mobile Pentium III
processor in the JTAG chain, except for those that are dictated by voltage requirements of the TAP
signals.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
22 Datasheet Order Number 283653-001
3.1.3 Catastrophic Thermal Protection
The mobile Pentium III processor does not support catastrophic thermal protection or the
THERMTRIP# signal. An external thermal sensor must be used to protect the processor and the
system against excessive temperatures.
3.1.4 Unused Signals
All signals named NC and RSVD must be unconnected. The TESTHI signal should be pulled up
to VCCT. The TESTLO1 and TESTLO2 signal should be pulled down to VSS. Unused GTL+
inputs, outputs and bi-directional signals should be unconnected. Unused CMOS active low inputs
should be connected to VCCT and unused active high inputs should be connected to VSS. Unused
Open-drain outputs should be unconnected. If the processor is configured to enter the Quick Start
state rather than the Stop Grant state, then the SLP# signal should be connected to VCCT. When
tying any signal to power or ground, a resistor will allow for system testability. For unused
signals, Intel suggests that 1.5-kΩ resistors are used for pull-ups and 1-kΩ resistors are used for
pull-downs.
If the local APIC is hardware disabled, then PICCLK and PICD[1:0] should be tied to VSS with a
1-kΩ resistor, one resistor can be used for the three signals. Otherwise PICCLK must be driven
with a clock that meets specification (see Table 18) and the PICD[1:0] signals must be pulled up
to VCCT with 150-Ω resistors, even if the local APIC is not used.
BSEL1 must be connected to VSS and BSEL0 must be pulled up to VCCT. VID[4:0] should be
connected to VSS if they are not used.
If the TAP signals are not used then the inputs should be pulled to ground with 1-kΩ resistors and
TDO should be left unconnected.
3.1.5 Signal State in Low-power States
3.1.5.1 System Bus Signals
All of the system bus signals have GTL+ input, output, or input/output drivers. Except when
servicing snoops, the system bus signals are tri-stated and pulled up by the termination resistors.
Snoops are not permitted in the Sleep and Deep Sleep states.
3.1.5.2 CMOS and Open-drain Signals
The CMOS input signals are allowed to be in either the logic high or low state when the processor
is in a low-power state. In the Auto Halt and Stop Grant states these signals are allowed to toggle.
These input buffers have no internal pull-up or pull-down resistors and system logic can use
CMOS or Open-drain drivers to drive them.
The Open-drain output signals have open drain drivers and external pull-up resistors are required.
One of the two output signals (IERR#) is a catastrophic error indicator and is tri-stated (and
pulled-up) when the processor is functioning normally. The FERR# output can be either tri-stated
or driven to VSS when the processor is in a low-power state depending on the condition of the
floating point unit. Since this signal is a DC current path when it is driven to VSS, Intel
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 23
recommends that the software clears or masks any floating-point error condition before putting the
processor into the Deep Sleep state.
3.1.5.3 Other Signals
The system bus clock (BCLK) must be driven in all of the low-power states except the Deep Sleep
state. The APIC clock (PICCLK) must be driven whenever BCLK is driven unless the APIC is
hardware disabled or the processor is in the Sleep state. Otherwise, it is permitted to turn off
PICCLK by holding it at VSS. The system bus clock should be held at VSS when it is stopped in the
Deep Sleep state.
In the Auto Halt and Stop Grant states the APIC bus data signals (PICD[1:0]) may toggle due to
APIC bus messages. These signals are required to be tri-stated and pulled-up when the processor
is in the Quick Start, Sleep, or Deep Sleep states unless the APIC is hardware disabled.
3.2 Power Supply Requirements
3.2.1 Decoupling Recommendations
The amount of bulk decoupling required on the VCC and VCCT planes to meet the voltage tolerance
requirements for the mobile Pentium III processor are a strong function of the power supply
design. Contact your Intel Field Sales Representative for tools to help determine how much bulk
decoupling is required.
For a processor with maximum performance mode at 900 MHz or 1 GHz, the transient de-
coupling recommendations are based on motherboard bulk decoupling, maximum Equivalent
Series Resistance (ESR) equal to 3.5mΩ, and the implementation of voltage positioning between
1.725V at light load and 1.660V at maximum load to reduce decoupling capacitor requirements.
Actual implementations will be dependent on power supply design.
For a processor with maximum performance mode at 700 MHz and above, the following
decoupling is recommended. The processor core power plane (VCC) should have fifteen 0.68 µF
0603 ceramic capacitors (using X7R dielectric for thermal reasons) placed directly under the
package using two vias for power and two vias for ground to reduce the trace inductance. Also to
minimize inductance, traces to those vias should be 22mils (in width) from the capacitor pads to
match the via-pad size (assuming 22-mil pad size). Twenty-four 2.2 µF 0805, X5R mid frequency
decoupling capacitors should be placed around the die as close to the die as flex solution allows.
The system bus buffer power plane (VCCT) should have twenty 0.1-µF high frequency decoupling
capacitors around the die.
For a processor with maximum performance mode at 650MHz and below, the following
decoupling is recommended. The processor core power plan (VCC) should have twelve 0.1-µF high
frequency decoupling capacitors placed underneath the die and twenty-seven 0.1-µF mid
frequency decoupling capacitors placed around the die as close to the die (< 0.8” away) as flex
solution allows. The system bus buffer power plane (VCCT) should have fifteen 0.1-µF high
frequency decoupling capacitors no further than 0.25 inches away from the VCCT vias (balls).
3.2.2 Voltage Planes
All VCC and VSS pins/balls must be connected to the appropriate voltage plane. All VCCT and VREF
pins/balls must be connected to the appropriate traces on the system electronics. In addition to the
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
24 Datasheet Order Number 283653-001
main VCC, VCCT, and VSS power supply signals, PLL1 and PLL2 provide analog decoupling to the
PLL section. PLL1 and PLL2 should be connected according to Figure 5. Do not connect PLL2
directly to VSS. Appendix A contains the RLC filter specification.
Figure 5. PLL RLC Filter
PLL1
PLL2
V
CCT
V0027-01
L1
C1
R1
3.3 System Bus Clock and Processor Clocking
The 2.5-V BCLK clock input directly controls the operating speed of the system bus interface. All
system bus timing parameters are specified with respect to the rising edge of the BCLK input. The
mobile Pentium III processor core frequency is a multiple of the BCLK frequency. The processor
core frequency is configured during manufacturing. The configured bus ratio is visible to software
in the Power-on configuration register, see Section 7.2 for details.
Multiplying the bus clock frequency is necessary to increase performance while allowing for
easier distribution of signals within the system. Clock multiplication within the processor is
provided by the internal Phase Lock Loop (PLL), which requires a constant frequency BCLK
input. During Reset or on exit from the Deep Sleep state, the PLL requires some amount of time to
acquire the phase of BCLK. This time is called the PLL lock latency, which is specified in
Section 3.7, AC timing parameters T18 and T47.
3.4 Intel SpeedStep Technology
The mobile Pentium III processor featuring Intel SpeedStep technology is specified to operate in
either of two modes, the “Maximum Performance Mode” or the “Battery Optimized Mode”. Each
frequency and voltage pair identifies the operating mode. The voltage provided to the processor
must meet the core voltage specification for the current operating mode. If an operating mode
transition is made, then the system logic must direct the voltage regulator to regulate to the voltage
specification of the other mode. After reset, the processor will start in the lower of its two core
frequencies, so the core voltage must meet the lower voltage specification. Any RESET# assertion
will force the processor to the lower frequency, and the core voltage must behave appropriately.
INIT# assertions ("soft" resets) and APIC bus INIT messages do not change the operating mode of
the processor. Some electrical and thermal specifications are for a specific voltage and frequency.
The mobile Pentium III processor featuring Intel SpeedStep technology will meet the electrical and
thermal specifications specific to the current operating mode and is not guaranteed to meet the
electrical and thermal specifications specific to the opposite operating mode. The timing
specifications in Table 22 must be met when performing an operating mode transition.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 25
3.5 Maximum Ratings
Table 8 contains the mobile Pentium III processor stress ratings. Functional operation at the
absolute maximum and minimum is neither implied nor guaranteed. The processor should not
receive a clock while subjected to these conditions. Functional operating conditions are provided
in the AC and DC tables. Extended exposure to the maximum ratings may affect device reliability.
Furthermore, although the processor contains protective circuitry to resist damage from static
electric discharge, one should always take precautions to avoid high static voltages or electric
fields.
Table 8. Mobile Pentium III Processor Absolute Maximum Ratings
Symbol Parameter Min Max Unit Notes
TStorage Storage Temperature –40 85 °C Note 1
VCC(Abs) Supply Voltage with respect to VSS –0.5 2.1 V
VCCT System Bus Buffer Voltage with respect to VSS –0.3 2.1 V
VIN GTL System Bus Buffer DC Input Voltage with respect to VSS –0.3 2.1 VNotes 2, 3
VIN GTL System Bus Buffer DC Input Voltage with respect to VCCT —VCCT + 0.7V VNotes 2, 4
VIN15 1.5V Buffer DC Input Voltage with respect to VSS –0.3 2.1 VNote 5
VIN25 2.5V Buffer DC Input Voltage with respect to VSS –0.3 3.3 VNote 6
VIN33 3.3V Buffer DC Input Voltage with respect to VSS –0.3 3.5 VNote 7
VINVID VID ball/pin DC Input Voltage with respect to VSS —5.5 V
IVID VID Current 5mA Note 8
NOTES:
1. The shipping container is only rated for 65°C.
2. Parameter applies to the GTL+ signal groups only. Compliance with both VIN GTL specifications is required.
3. The voltage on the GTL+ signals must never be below –0.3 or above 2.1V with respect to ground.
4. The voltage on the GTL+ signals must never be above VCCT + 0.7V even if it is less than VSS + 2.1V, or a short to
ground may occur.
5. Parameter applies to CMOS, Open-drain, APIC, and TAP bus signal groups only.
6. Parameter applies to BCLK, CLKREF, PICCLK and PWRGOOD signals.
7. Parameter applies to BSEL[1:0] signals.
8. Parameter applies to each VID pin/ball individually.
3.6 DC Specifications
Table 9A through Table 12 lists the DC specifications for the mobile Pentium III processor.
Specifications are valid only while meeting specifications for the junction temperature, clock
frequency, and input voltages. Care should be taken to read all notes associated with each
parameter.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
26 Datasheet Order Number 283653-001
Table 9A. Mobile Pentium III Processor DC Specifications
Symbol Parameter Min Typ Max Unit Notes
VCC Transient VCC for core logic 0.95
1.02
1.25
1.485
1.62
0.975
1.10
1.35
1.60
1.70
1.0
1.18
1.45
1.715
1.825
V
V
V
V
V
±25 mV
±80 mV
±100 mV
±115 mV
-80/+125 mV,
Note 5,6
VCC,DC Static VCC for core logic 0.95
1.02
1.25
1.485
1.62
0.975
1.10
1.35
1.60
1.70
1.0
1.18
1.45
1.640
1.74
V
V
V
V
V
±25 mV
±80 mV
±100 mV
-115/+40 mV
-80/+40 mV,
Note 2,6
VCCT VCC for System Bus Buffers, Transient tolerance 1.385 1.50 1.615 V±115 mV,
Note 5,6
VCCT,DC VCC for System Bus Buffers, Static tolerance 1.455 1.50 1.545 V±3%, Note 2,6
dICC/dt VCC power supply current slew rate 1400 A/µsNotes 3,4
NOTES:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. Static voltage regulation includes: DC output initial voltage set point adjust, output ripple and noise, output load ranges
specified in above, temperature, and warm up.
3. Based on simulations and averaged over the duration of any change in current. Use to compute the maximum inductance
and reaction time of the voltage regulator. This parameter is not tested.
4. Maximum values specified by design/characterization at nominal VCC and VCCT.
5. VCCx must be within this range under all operating conditions, including maximum current transients. VCCx must return to
within the static voltage specification, VCCx,DC, within 100 µs after a transient event.
6. Voltages are measured at the processor package pin for the Micro-PGA2 part and at the package ball on the BGA2 part.
7. TJ = 0°C to 100°C
Table 9B. Mobile Pentium III Processor DC Specifications
Core Speed Vcc (nominal) Icc (max) IccT5 (max) IccSG6 (max) IccQS7 (max)IccDSLP8 (max) Unit
500 / 300 MHz
600 / 300 MHz
600 / 500 MHz
700 / 500 MHz
750 / 500 MHz
700 / 550 MHz
750 / 600 MHz
800 / 650 MHz
850 / 700 MHz
900 / 700 MHz
1GHz / 700 MHz
1.1 / 0.975V
1.1 / 0.975V
1.35 / 1.10V
1.35 / 1.10V
1.35 / 1.10V
1.60 / 1.35V
1.60 / 1.35V
1.60 / 1.35V
1.60 / 1.35V
1.70 / 1.35V
1.70 / 1.35V
7.90 / 4.72
9.14 / 4.72
11.20 / 7.90
12.80 / 7.90
13.49 / 7.90
14.60 / 10.30
15.60 / 11.20
16.60 / 12.00
17.60 / 12.80
19.30 / 12.80
21.10 / 12.80
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
2.50 / 2.50
1.50 / 1.30
1.50 / 1.30
1.70 / 1.50
2.70 / 1.50
2.70 / 1.50
2.20 / 1.70
2.20 / 1.70
3.50 / 2.70
3.50 / 2.70
3.91 / 2.70
3.91 / 2.70
1.30 / 1.20
1.30 / 1.20
1.50 / 1.30
2.40 / 1.30
2.40 / 1.30
1.90 / 1.50
1.90 / 1.50
3.00 / 2.40
3.00 / 2.40
3.46 / 2.40
3.46 / 2.40
1.10 / 1.10
1.10 / 1.10
1.20 / 1.10
2.10 / 1.10
2.10 / 1.10
1.60 / 1.20
1.60 / 1.20
2.50 / 2.10
2.50 / 2.10
3.00 / 2.50
3.00 / 2.50
A
A
A
A
A
A
A
A
A
A
A
NOTES:
1. ICCT is the current supply for the system bus buffers, including the on-die termination.
2. ICCx,max specifications are specified at VCC, DC max, VCCT,max, and 100°C and under maximum signal loading conditions.
3. Battery Optimized mode current is based on design / characterization only. Not 100% tested.
4. Icc is current for VCC at core frequency. Not 100% tested. Specified by design/characterization.
5. IccT is current for VCCT . Not 100% tested. Specified by design/characterization.
6. IccSG is Stop Grant and Auto Halt current. Not 100% tested. Specified by design/characterization.
7. IccQS is Quick Start and Sleep current. Not 100% tested. Specified by design/characterization.
8. IccDSLP is Deep Sleep Leakage current
9. Format: (Maximum Performance Mode Parameter) / (Battery Optimized Mode Parameter)
The signals on the mobile Pentium III processor system bus are included in the GTL+ signal
group. These signals are specified to be terminated to VCC. The DC specifications for these signals
are listed in
Table 10 and the termination and reference voltage specifications for these signals are listed in
Table 11.
The mobile Pentium III processor requires external termination and a VREF. Refer to the Mobile
Pentium III Processor GTL+ System Bus Layout Guideline for full details of system VCCT and
VREF requirements. The CMOS, Open-drain, and TAP signals are designed to interface at 1.5V
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 27
levels to allow connection to other devices. BCLK and PICCLK are designed to receive a 2.5-V
clock signal. The DC specifications for these signals are listed Table 12.
Table 10. GTL+ Signal Group DC Specifications
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125
mV ; VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Notes
VOH Output High Voltage — — VSee VCCT,max in Table 11
RON Output Low Drive Strength 16.67 Ω
ILLeakage Current for Inputs, Outputs and I/Os ±100 µANote 1
NOTE: (0 ≤ VIN/OUT ≤ VCCT).
Table 11. GTL+ Bus DC Specifications
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125
mV ; VCCT = 1.50V ±115 mV
Symbol Parameter Min Typ Max Unit Notes
VCCT Bus Termination Voltage 1.385 1.5 1.615 VNote 1
VREF Input Reference Voltage 2/3VCCT – 2% 2/3VCCT 2/3VCCT + 2% V±2%, Note 2
RTT Bus Termination Strength 50 56 65 ΩOn-die RTT, Note
3
NOTES:
1. For simulation use 1.50V ±10%. For typical simulation conditions use VCCTmin (1.5V –10%).
2. VREF should be created from VCCT by a voltage divider.
3. The RESET# signal does not have an on-die RTT. It requires an off-die 56.2Ω ±1% terminating resistor connected to
VCCT.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
28 Datasheet Order Number 283653-001
Table 12. Clock, APIC, TAP, CMOS, and Open-drain Signal Group DC Specifications
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV ;
VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Notes
VIL15 Input Low Voltage, 1.5V CMOS –0.15 VCMOSREFmin –
200 mV V
VIL25 Input Low Voltage, 2.5V CMOS –0.3 0.7 VNotes 1, 2
VIL33 Input Low Voltage, 3.3V CMOS –0.3 VCMOSREFmin –
200 mV VNotes 7
VIL,BCLK Input Low Voltage, BCLK –0.3 0.5 VNote 2
VIH15 Input High Voltage, 1.5V CMOS VCMOSREFmax +
200 mV VCCT V
VIH25 Input High Voltage, 2.5V CMOS 2.0 2.625 VNotes 1, 2
VIH33 Input High Voltage, 3.3V CMOS VCMOSREFmax +
200 mV 3.465 VNotes 7
VIH,BCLK Input High Voltage, BCLK 2.0 2.625 VNote 2
VOL Output Low Voltage 0.4 VNote 3
VOH15 Output High Voltage, 1.5V CMOS N/A 1.615 VAll outputs are Open-drain
VOH25 Output High Voltage, 2.5V CMOS N/A 2.625 VAll outputs are Open-drain
VOH,VID Output High Voltage, VID ball/pins N/A 5.50 V5V + 10%
VCMOSREF CMOSREF Voltage 0.90 1.10 VNote 4
VCLKREF CLKREF Voltage 1.175 1.325 V1.25V ±6% 4
IOL Output Low Current 10 mA Note 6
ILLeakage Current for Inputs, Outputs
and I/Os ±100 µANote 5, Note 8
NOTES:
1. Parameter applies to the PICCLK and PWRGOOD signals only.
2. VILx,min and VIHx,max only apply when BCLK and PICCLK are stopped. BCLK and PICCLK should be stopped in the low
state. See Table 23 for the BCLK voltage range specifications for when BCLK is running. See Table 24 for the PICCLK
voltage range specifications for when PICCLK is running.
3. Parameter measured at 10 mA.
4. VCMOSREF and VCLKREF should be created from a stable voltage supply using a voltage divider.
5. (0 ≤ VIN/OUT ≤ VIHx,max).
6. Specified as the minimum amount of current that the output buffer must be able to sink. However, VOL,max cannot be
guaranteed if this specification is exceeded.
7. Parameter applies to BSEL[1:0] signals only.
8. For BSEL[1:0] signals, IL, Max can be up to 100µA (with 1K pull-up to 1.5V), and can be upto 500µA (with 1K pull-up to
3.3V)
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 29
3.7 AC Specifications
3.7.1 System Bus, Clock, APIC, TAP, CMOS, and Open-drain AC
Specifications
Table 13 through Table 21 provide AC specifications associated with the mobile Pentium III
processor. The AC specifications are divided into the following categories: Table 13 contains the
system bus clock specifications; Table 14 contains the processor core frequencies; Table 15
contains the GTL+ specifications; Table 16 contains the CMOS and Open-drain signal groups
specifications; Table 17 contains timings for the reset conditions; Table 18 contains the APIC
specifications; Table 19 contains the TAP specifications; and Table 20 and Table 21 contain the
power management timing specifications.
All system bus AC specifications for the GTL+ signal group are relative to the rising edge of the
BCLK input at 1.25V. All GTL+ timings are referenced to VREF for both “0” and “1” logic levels
unless otherwise specified. All APIC, TAP, CMOS, and Open-drain signals except PWRGOOD
are referenced to 0.75V.
Table 13. System Bus Clock AC Specifications1
T
J
= 0°C to 100°C; V
CC
= 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV
; VCCT = 1.50V ±115 mV
Symbol Parameter Min Typ Max Unit Figure Notes
System Bus Frequency 100 MHz
T1 BCLK Period 10 ns Figure 7 Note 2
T2 BCLK Period Stability ±250 ps Notes 3, 4
T3 BCLK High Time 2.70 ns Figure 7 at>2.0V
T4 BCLK Low Time 2.45 ns Figure 7 at<0.5V
T5 BCLK Rise Time 0.175 0.875 ns Figure 7 (0.9V – 1.6V)
T6 BCLK Fall Time 0.175 0.875 ns Figure 7 (1.6V – 0.9V)
NOTES:
1. All AC timings for GTL+ and CMOS signals are referenced to the BCLK rising edge at 1.25V. All CMOS signals are
referenced at 0.75V.
2. The BCLK period allows a +0.5 ns tolerance for clock driver variation.
3. Not 100% tested. Specified by design/characterization.
4. Measured on the rising edge of adjacent BCLKs at 1.25V. The jitter present must be accounted for as a component of
BCLK skew between devices.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
30 Datasheet Order Number 283653-001
Table 14. Valid Mobile Pentium III Processor Frequencies
T
J
= 0°C to 100°C; V
CC
= 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV
; VCCT = 1.50V ±115 mV
BCLK Frequency
(MHz) Frequency Multiplier Core Frequency
(MHz) Power-on Configuration
bits [27, 25:22]
100 3300 0, 0001
100 4400 0, 0010
100 4.5 450 0, 0110
100 5500 0, 0000
100 5.5 550 0, 0100
100 6600 0, 1011
100 6.5 650 0, 1111
100 7700 0, 1001
100 7.5 750 0, 1101
100 8800 0, 1010
100 8.5 850 1, 0110
100 9900 1, 0000
100 10 1000 1, 1011
NOTE: While other combinations of bus and core frequencies are defined, operation at frequencies other than those
listed above will not be validated by Intel and are not guaranteed. The frequency multiplier is programmed into
the processor when it is manufactured and it cannot be changed.
Table 15. GTL+ Signal Groups AC Specifications1
RTT = 56Ω internally terminated to VCCT; VREF = 2/3VCCT; load = 0 pF;
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV ;
VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Figure Notes
T7 GTL+ Output Valid Delay 0.2
0.2 2.7
3.4 ns
ns Figure 8 Note 6
Note 7
T8 GTL+ Input Setup Time 1.2 ns Figure 9 Notes 2, 3
T9 GTL+ Input Hold Time 0.80
1.2 ns
ns Figure 9 Note 4, 6
Note 7
T10 RESET# Pulse Width 1ms Figure 10,
Figure 11 Note 5
NOTES:
1. All AC timings for GTL+ signals are referenced to the BCLK rising edge at 1.25V. All GTL+ signals are referenced at
VREF.
2. RESET# can be asserted (active) asynchronously, but must be de-asserted synchronously.
3. Specification is for a minimum 0.40V swing.
4. Specification is for a maximum 1.0V swing.
5. After VCC, VCCT, and BCLK become stable and PWRGOOD is asserted.
6. Applies to all core VCC other than 0.975V and 1.10V
7. Applies to core VCC = 0.975V and VCC = 1.10V
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 31
Table 16. CMOS and Open-drain Signal Groups AC Specifications1, 2
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV ;
VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Figure Notes
T14 1.5V Input Pulse Width, except PWRGOOD and
LINT[1:0] 2BCLKs Figure 8 Active and
Inactive states
T14B LINT[1:0] Input Pulse Width 6BCLKs Figure 8 Note 3
T15 PWRGOOD Inactive Pulse Width 10 BCLKs Figure 11 Notes 4, 5
NOTES:
1. All AC timings for CMOS and Open-drain signals are referenced to the BCLK rising edge at 1.25V. All CMOS and
Open-drain signals are referenced at 0.75V.
2. Minimum output pulse width on CMOS outputs is 2 BCLKs.
3. This specification only applies when the APIC is enabled and the LINT1 or LINT0 signal is configured as an edge
triggered interrupt with fixed delivery, otherwise specification T14 applies.
4. When driven inactive, or after VCC, VCCT and BCLK become stable. PWRGOOD must remain below VIL25,max from Table
12 until all the voltage planes meet the voltage tolerance specifications in Table 9A and BCLK has met the BCLK AC
specifications in Table 13 for at least 10 clock cycles. PWRGOOD must rise glitch-free and monotonically to 2.5V.
5. If the BCLK Settling Time specification (T60) can be guaranteed at power-on reset then the PWRGOOD Inactive Pulse
Width specification (T15) is waived and BCLK may start after PWRGOOD is asserted. PWRGOOD must still remain
below VIL25,max until all the voltage planes meet the voltage tolerance specifications.
Table 17. Reset Configuration AC Specifications
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV ;
VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Figure Notes
T16 Reset Configuration Signals (A[15:5]#, BREQ0#,
FLUSH#, INIT#, PICD0) Setup Time 4BCLKs Figure 8.
Figure 9 Before deassertion
of RESET#
T17 Reset Configuration Signals (A[15:5]#, BREQ0#,
FLUSH#, INIT#, PICD0) Hold Time 2 20 BCLKs Figure 8.
Figure 9 After clock that
deasserts RESET#
T18 RESET#/PWRGOOD Setup Time 1ms Figure 11 Before deassertion
of RESET# 1
NOTE: At least 1 ms must pass after PWRGOOD rises above VIH25,min from Table 12 and BCLK meets its AC timing
specification until RESET# may be deasserted.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
32 Datasheet Order Number 283653-001
Table 18. APIC Bus Signal AC Specifications1
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV ;
VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Figure Notes
T21 PICCLK Frequency 233.3 MHz Note 2
T22 PICCLK Period 30 500 ns Figure 6
T23 PICCLK High Time 10.5 ns Figure 6 at>1.7V
T24 PICCLK Low Time 10.5 ns Figure 6 at<0.7V
T25 PICCLK Rise Time 0.25 3.0 ns Figure 6 (0.7V – 1.7V)
T26 PICCLK Fall Time 0.25 3.0 ns Figure 6 (1.7V – 0.7V)
T27 PICD[1:0] Setup Time 5.0 ns Figure 9 Note 3
T28 PICD[1:0] Hold Time 2.5 ns Figure 9 Note 3
T29 PICD[1:0] Valid Delay (Rising Edge)
PICD[1:0] Valid Delay (Falling Edge) 1.5
1.5 8.7
12.0 Ns
ns Figure 8 Notes 3, 4, 5
NOTES:
1. All AC timings for APIC signals are referenced to the PICCLK rising edge at 1.25V. All CMOS signals are referenced at
0.75V.
2. The minimum frequency is 2 MHz when PICD0 is at 1.5V at reset. If PICD0 is strapped to VSS at reset then the
minimum frequency is 0 MHz.
3. Referenced to PICCLK Rising Edge.
4. For Open-drain signals, Valid Delay is synonymous with Float Delay.
5. Valid delay timings for these signals are specified into 150Ω to 1.5V and 0 pF of external load. For real system timings
these specifications must be derated for external capacitance at 105 ps/pF.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 33
Table 19. TAP Signal AC Specifications1
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV ;
VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Figure Notes
T30 TCK Frequency —16.67 MHz
T31 TCK Period 60 —ns Figure 6
T32 TCK High Time 25.0 ns Figure 6 ≥ 1.2V, Note 2
T33 TCK Low Time 25.0 ns Figure 6 ≤ 0.6V, Note 2
T34 TCK Rise Time 5.0 ns Figure 6 (0.6V – 1.2V), Notes 2, 3
T35 TCK Fall Time 5.0 ns Figure 6 (1.2V – 1.6V), Notes 2, 3
T36 TRST# Pulse Width 40.0 ns Figure 13 Asynchronous, Note 2
T37 TDI, TMS Setup Time 5.0 ns Figure 12 Note 4
T38 TDI, TMS Hold Time 14.0 ns Figure 12 Note 4
T39 TDO Valid Delay 1.0 10.0 ns Figure 12 Notes 5, 6
T40 TDO Float Delay 25.0 ns Figure 12 Notes 2, 5, 6
T41 All Non-Test Outputs Valid Delay 2.0 25.0 ns Figure 12 Notes 5, 7, 8
T42 All Non-Test Outputs Float Delay 25.0 ns Figure 12 Notes 2, 5, 7, 8
T43 All Non-Test Inputs Setup Time 5.0 ns Figure 12 Notes 4, 7, 8
T44 All Non-Test Inputs Hold Time 13.0 ns Figure 12 Notes 4, 7, 8
NOTES:
1. All AC timings for TAP signals are referenced to the TCK rising edge at 0.75V. All TAP and CMOS signals are
referenced at 0.75V.
2. Not 100% tested. Specified by design/characterization.
3. 1 ns can be added to the maximum TCK rise and fall times for every 1 MHz below 16 MHz.
4. Referenced to TCK rising edge.
5. Referenced to TCK falling edge.
6. Valid delay timing for this signal is specified into 150Ω terminated to 1.5V and 0 pF of external load. For real system
timings these specifications must be derated for external capacitance at 105 ps/pF.
7. Non-Test Outputs and Inputs are the normal output or input signals (except TCK, TRST#, TDI, TDO, and TMS). These
timings correspond to the response of these signals due to boundary scan operations.
8. During Debug Port operation use the normal specified timings rather than the TAP signal timings.
Table 20. Quick Start/Deep Sleep AC Specifications1
T
J
= 0°C to 100°C; V
CC
= 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125 mV
; VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Figure Notes
T45 Stop Grant Cycle Completion to Clock Stop 100 BCLKs Figure 14
T46 Stop Grant Cycle Completion to Input Signals Stable 0µsFigure 14
T47 Deep Sleep PLL Lock Latency 0 30 µsFigure 14,
Figure 15 Note 2
T48 STPCLK# Hold Time from PLL Lock 0ns Figure 14
T49 Input Signal Hold Time from STPCLK# Deassertion 8BCLKs Figure 14
NOTES:
1. Input signals other than RESET# and BPRI# must be held constant in the Quick Start state.
2. The BCLK Settling Time specification (T60) applies to Deep Sleep state exit under all conditions.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
34 Datasheet Order Number 283653-001
Table 21. Stop Grant/Sleep/Deep Sleep AC Specifications
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125
mV ; VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Figure
T50 SLP# Signal Hold Time from Stop Grant Cycle Completion 100 BCLKs Figure 15
T51 SLP# Assertion to Input Signals Stable 0ns Figure 15
T52 SLP# Assertion to Clock Stop 10 BCLKs Figure 15
T54 SLP# Hold Time from PLL Lock 0ns Figure 15
T55 STPCLK# Hold Time from SLP# Deassertion 10 BCLKs Figure 15
T56 Input Signal Hold Time from SLP# Deassertion 10 BCLKs Figure 15
NOTE: Input signals other than RESET# must be held constant in the Sleep state. The BCLK Settling Time specification
(T60) applies to Deep Sleep state exit under all conditions.
Table 22. Intel SpeedStep Technology AC Specifications
TJ = 0°C to 100°C; VCC = 0.975V ±25 mV or 1.10V ±80 mV or 1.35V ±100 mV or 1.60V ±115 mV or 1.70V -80/+125
mV ; VCCT = 1.50V ±115 mV
Symbol Parameter Min Max Unit Figure Notes
T57 GHI# Setup Time from BCLK Restart 150 ns Figure 16 Note 1
T58 GHI# Hold Time from BCLK Restart 30 µsFigure 16 Note 1
T59 GHI# Sample Delay 10 µsFigure 16 Note 1
T60 BCLK Settling Time 150 ns Figure 16 Notes 2, 3
NOTES:
1. GHI# is ignored until 10 µs after BCLK stops, the setup and hold window must occur after this time.
2. BCLK must meet the BCLK AC specification from Table 13 within 150 ns of turning on (rising above VIL,BCLK).
3. This specification applies to the exit from the Deep Sleep state whether or not a Intel SpeedStep technology operating
mode transition occurs.
Figure 6 through Figure 16 are to be used in conjunction with Table 13 through Table 22.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 35
Figure 6. PICCLK/TCK Clock Timing Waveform
CLK VH
VLVTRIP
Th
Tl
Tp
Tr
Tf
D0003-01
NOTES: Tr=T34, T25 (Rise Time)
Tf=T35, T26 (Fall Time)
Th=T32, T23 (High Time)
Tl=T33, T24 (Low Time)
Tp=T31, T22 (Period)
VTRIP =1.25V for PICCLK; 0.75V for TCK
VL=0.7V for PICCLK; 0.6V for TCK
VH=2.0V for PICCLK; 1.2V for TCK
Figure 7. BCLK Timing Waveform
CLK VHVTRIP
Th
Tl
Tp
Tr
D0003-02
VL
Tf
1.6V
0.9V
NOTES: Tr=T5 (Rise Time)
Tf=T6 (Fall Time)
Th=T3 (High Time)
Tl=T4 (Low Time)
Tp=T1 (Period)
VTRIP =1.25V for BCLK
VL=0.5V for BCLK
VH=2.0V for BCLK
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
36 Datasheet Order Number 283653-001
Figure 8. Valid Delay Timings
CLK
Signal
TXTx
TPW
VValid Valid
D0004-00
NOTES: Tx=T7, T11, T29 (Valid Delay)
Tpw =T14, T14B (Pulse Width)
V=VREF for GTL+ signal group; 0.75V for CMOS, Open-drain, APIC, and TAP signal groups
Figure 9. Setup and Hold Timings
CLK
Signal
VValid
Th
Ts
D0005-00
NOTES: Ts=T8, T12, T27 (Setup Time)
Th=T9, T13, T28 (Hold Time)
V=VREF for GTL+ signals; 0.75V for CMOS, APIC, and TAP signals
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 37
Figure 10. Cold/Warm Reset and Configuration Timings
BCLK
RESET#
Configuration
(A[15:5], BREQ0#,
FLUSH#, INIT#,
PICD0)
Tv
Tx
Tt
Tu
Tw
Valid
D0006-01
NOTES: Tt=T9 (GTL+ Input Hold Time)
Tu=T8 (GTL+ Input Setup Time)
Tv=T10 (RESET# Pulse Width)
T18 (RESET#/PWRGOOD Setup Time)
Tw=T16 (Reset Configuration Signals (A[15:5]#, BREQ0#, FLUSH#, INIT#, PICD0) Setup Time)
Tx=T17 (Reset Configuration Signals (A[15:5]#, BREQ0#, FLUSH#, INIT#, PICD0) Hold Time)
Figure 11. Power-on Reset Timings
BCLK
PWRGOOD
RESET#
TaTb
V ,
CC
VREF
V ,
CCT,
VIL25,max VIH25,min
D0007-01
NOTES: Ta=T15 (PWRGOOD Inactive Pulse Width)
Tb=T10 (RESET# Pulse Width)
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
38 Datasheet Order Number 283653-001
Figure 12. Test Timings (Boundary Scan)
TCK
TDI, TMS
Input
Signals
TDO
Output
Signals
0.75V
TvTw
TrTs
TxTu
TyTz
D0008-01
NOTES: Tr=T43 (All Non-Test Inputs Setup Time)
Ts=T44 (All Non-Test Inputs Hold Time)
Tu=T40 (TDO Float Delay)
Tv=T37 (TDI, TMS Setup Time)
Tw=T38 (TDI, TMS Hold Time)
Tx=T39 (TDO Valid Delay)
Ty=T41 (All Non-Test Outputs Valid Delay)
Tz=T42 (All Non-Test Outputs Float Delay)
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 39
Figure 13. Test Reset Timings
TRST# 0.75V
TqD0009-01
NOTE: Tq=T36 (TRST# Pulse Width)
Figure 14. Quick Start/Deep Sleep Timing
Tw
stpgnt
Running Running
BCLK
STPCLK#
CPU bus
SLP#
Compatibility
Signals Changing
Normal Quick Start Deep Sleep Quick Start Normal
Frozen
Tv
Ty
Tz
Tx
V0010-00
NOTES: Tv=T45 (Stop Grant Acknowledge Bus Cycle Completion to Clock Shut Off Delay)
Tw=T46 (Setup Time to Input Signal Hold Requirement)
Tx=T47 (Deep Sleep PLL Lock Latency)
Ty=T48 (PLL lock to STPCLK# Hold Time)
Tz=T49 (Input Signal Hold Time)
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
40 Datasheet Order Number 283653-001
Figure 15. Stop Grant/Sleep/Deep Sleep Timing
Tu
stpgnt
Running
BCLK
STPCLK#
CPU bus
SLP#
Compatibility
Signals FrozenChanging
Normal Stop
Grant Sleep Deep Sleep Sleep Stop
Grant Normal
Running
Tt
Tv
Ty
Tz
TwTx
V0011-00
Changing
NOTES: Tt=T50 (Stop Grant Acknowledge Bus Cycle Completion to SLP# Assertion Delay)
Tu=T51 (Setup Time to Input Signal Hold Requirement)
Tv=T52 (SLP# assertion to clock shut off delay)
Tw=T47 (Deep Sleep PLL lock latency)
Tx=T54 (SLP# Hold Time)
Ty=T55 (STPCLK# Hold Time)
Tz=T56 (Input Signal Hold Time)
Figure 16. Intel SpeedStep Technology/Deep Sleep Timing
BCLK VIL25
BCLK off BCLK on
(out of spec) BCLK on
(in spec)
1.25V1.25V
BCLK on
Ts
V0036-00
GHI#
Th
Ty
Tx
NOTES: Ts=T57 (GHI# Setup Time from BCLK Restart)
Th=T58 (GHI# Hold Time from BCLK Restart)
Tx=T59 (GHI# Sample Delay)
Ty=T60 (BCLK Settling Time)
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 41
4. System Signal Simulations
Many scenarios have been simulated to generate a set of GTL+ processor system bus layout
guidelines, which are available in the Mobile Coppermine Processor GTL+ System Bus Layout
Guideline. Systems must be simulated using the IBIS model to determine if they are compliant
with this specification.
4.1 System Bus Clock (BCLK) and PICCLK AC Signal Quality
Specifications
Table 23 and Figure 17 show the signal quality for the system bus clock (BCLK) signal, and
Table 24 and Figure 17 show the signal quality for the APIC bus clock (PICCLK) signal at the
processor. BCLK and PICCLK are 2.5V clocks.
Table 23. BCLK Signal Quality Specifications
Symbol Parameter Min Max Unit Figure Notes
V1 VIL,BCLK 0.5 VFigure 17 Note 1
V2 VIH,BCLK 2.0 VFigure 17 Note 1
V3 VIN Absolute Voltage Range -0.7 3.5 VFigure 17 Undershoot/Overshoot, Note 2
V4 BCLK Rising Edge Ringback 2.0 VFigure 17 Absolute Value, Note 3
V5 BCLK Falling Edge Ringback 0.5 VFigure 17 Absolute Value, Note 3
NOTES:
1. The clock must rise/fall monotonically between VIL,BCLK and VIH,BCLK .
2. These specifications apply only when BCLK is running, see Table 12 for the DC specifications for when BCLK is
stopped. BCLK may not be above VIH,BCLK,max or below VIL,BCLK,min for more than 50% of the clock cycle.
3. The rising and falling edge ringback voltage specified is the minimum (rising) or maximum (falling) absolute voltage the
BCLK signal can go to after passing the VIH,BCLK (rising) or VIL,BCLK (falling) voltage limits.
Table 24. PICCLK Signal Quality Specifications
Symbol Parameter Min Max Unit Figure Notes
V1 VIL25 0.7 VFigure 17 Note 1
V2 VIH25 2.0 VFigure 17 Note 1
V3 VIN Absolute Voltage Range -0.7 3.5 VFigure 17 Undershoot,Overshoot, Note 2
V4 PICCLK Rising Edge Ringback 2.0 VFigure 17 Absolute Value, Note 3
V5 PICCLK Falling Edge Ringback 0.7 VFigure 17 Absolute Value, Note 3
NOTES:
1. The clock must rise/fall monotonically between VIL25 and VIH25.
2. These specifications apply only when PICCLK is running, see Table 12 for the DC specifications for when PICCLK is
stopped. PICCLK may not be above VIH25,max or below VIL25,min for more than 50% of the clock cycle.
3. The rising and falling edge ringback voltage specified is the minimum (rising) or maximum (falling) absolute voltage the
PICCLK signal can go to after passing the VIH25 (rising) or VIL25 (falling) voltage limits.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
42 Datasheet Order Number 283653-001
Figure 17. BCLK/PICCLK Generic Clock Waveform
V0012-01
V1
V2
V3max
V4
V3min
V5
4.2 GTL+ AC Signal Quality Specifications
Table 25, Figure 18, and Figure 19 illustrate the GTL+ signal quality specifications for the mobile
Pentium III processor. Refer to the Pentium® II Processor Developer’s Manual for the GTL+
buffer specification. The mobile Pentium III processor maximum overshoot and undershoot
specifications for a given duration of time are specified in Table 26. Contact your Intel Field Sales
representative for a copy of the OVERSHOOT_CHECKER tool. The OVERSHOOT_CHECKER
determines if a specific waveform meets the overshoot/undershoot specification. Figure 20 shows
the overshoot/undershoot waveform. The tolerances listed in Table 26 are conservative. Signals
that exceed these tolerances may still meet the processor overshoot/undershoot tolerance if the
OVERSHOOT_CHECKER tool says that they pass.
Table 25. GTL+ Signal Group Ringback Specification
Symbol Parameter Min Unit Figure Notes
αOvershoot 100 mV Figure 18,
Figure 19 Notes 1, 2
τMinimum Time at High 0.5 ns Figure 18,
Figure 19 Notes 1, 2
ρAmplitude of Ringback -200 mV Figure 18,
Figure 19 Notes 1, 2, 3
φFinal Settling Voltage 200 mV Figure 18,
Figure 19 Notes 1, 2
δDuration of Sequential Ringback N/A ns Figure 18,
Figure 19 Notes 1, 2
NOTES:
1. Specified for the edge rate of 0.3 – 0.8 V/ns. See Figure 18 for the generic waveform.
2. All values determined by design/characterization.
3. Ringback below VREF,max + 200 mV is not authorized during low to high transitions. Ringback above VREF,min – 200 mV is
not authorized during high to low transitions.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 43
Figure 18. Low to High, GTL+ Receiver Ringback Tolerance
VREF,max+0.2V
Time
τ
δ
ρ
φ
α
VREF,min-0.2V
VREF,max
Vstart
Clock
VIL,BCLK
VIH,BCLK
V0014-01
Figure 19. High to Low, GTL+ Receiver Ringback Tolerance
VREF,max+0.2V
Time
VREF,min-0.2V
VREF,min
Vstart
Clock
VIL,BCLK
VIH,BCLK
V0014-02
τ
δ
ρ
φ
α
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
44 Datasheet Order Number 283653-001
Table 26. GTL+ Signal Group Overshoot/Undershoot Tolerance at the Processor Core1, 4, 5
Overshoot Amplitude 2 Undershoot Amplitude 3 Allowed Pulse Duration
2.0V -0.35V 0.35 ns
1.9V -0.25V 1.2 ns
1.8V -0.15V 4.3 ns
NOTES:
1. Under no circumstances should the GTL+ signal voltage ever exceed 2.0V maximum with respect to ground or -2.0V
minimum with respect to VCCT (i.e., VCCT - 2.0V) under operating conditions.
2. Ringbacks below VCCT cannot be subtracted from overshoots. Lesser undershoot does not allocate longer or larger
overshoot.
3. Ringbacks above ground cannot be subtracted from undershoots. Lesser overshoot does not allocate longer or larger
undershoot.
4. System designers are encouraged to follow Intel provided GTL+ layout guidelines.
5. All values are specified by design characterization and are not tested.
Figure 20. Maximum Acceptable Overshoot/Undershoot Waveform
VCCT
2.0V Max
1.9V
1.8V
Vss
Time dependant Overshoot
Time dependant
Undershoot
-.15V
-.25V
-.35V Min
αβ
χ
α
β
χ
NOTE: The total overshoot/undershoot budget for one clock cycle is fully consumed by the α, β, or χ waveforms.
4.3 Non-GTL+ Signal Quality Specifications
Signals driven to the mobile Pentium III processor should meet signal quality specifications to
ensure that the processor reads data properly and that incoming signals do not affect the long-term
reliability of the processor. Unlike previous generations of mobile processors, the mobile Pentium
III processor uses GTL+ buffers for non-GTL+ signals. The input and output paths of the buffers
have been slowed down to match the requirements for the non-GTL+ signals. The signal quality
specifications for the non-GTL+ signals are identical to the GTL+ signal quality specifications
except that they are relative to VCMOSREF rather than VREF transitions
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 45
OVERSHOOT_CHECKER can be used to verify non-GTL+ signal compliance with the signal
overshoot and undershoot tolerance. The tolerances listed in Table 27 are conservative. Signals
that exceed these tolerances may still meet the processor overshoot and undershoot tolerance if the
OVERSHOOT_CHECKER tool says that they pass.
Table 27. Non-GTL+ Signal Group Overshoot/Undershoot Tolerance at the Processor Core 1, 4, 5
Overshoot Amplitude 2 Undershoot Amplitude 3 Allowed Pulse Duration
2.1V -0.45V 0.45 ns
2.0V -0.35V 1.5 ns
1.9V -0.25V 5.0 ns
1.8V -0.15V 17 ns
NOTES:
1. Under no circumstances should the non-GTL+ signal voltage ever exceed 2.1V maximum with respect to ground or -
2.1V minimum with respect to VCCT (i.e., VCCT - 2.1V) under operating conditions.
2. Ring-backs below VCCT cannot be subtracted from overshoots. Lesser undershoot does not allocate longer or larger
overshoot.
3. Ring-backs above ground cannot be subtracted from undershoots. Lesser overshoot does not allocate longer or larger
undershoot.
4. System designers are encouraged to follow Intel provided non-GTL+ layout guidelines.
5. All values are specified by design characterization, and are not tested.
4.3.1 PWRGOOD Signal Quality Specifications
The processor requires PWRGOOD to be a clean indication that clocks and the power supplies
(VCC, VCCT, etc.) are stable and within their specifications. Clean implies that the signal will
remain below VIL25 and without errors from the time that the power supplies are turned on, until
they come within specification. The signal will then transition monotonically to a high (2.5V)
state. PWRGOOD may not ringback below 2.0V after rising above VIH25.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
46 Datasheet Order Number 283653-001
5. Mechanical Specifications
5.1 Surface-mount BGA2 Package Dimensions
The mobile Pentium III processor is packaged in a PBGA-B495 package (also known as BGA2)
with the back of the processor die exposed on top. Unlike previous mobile processors with
exposed die, the back of the mobile Pentium III processor die may be polished and very smooth.
The mechanical specifications for the surface-mount package are provided in Table 28. Figure 21
shows the top and side views of the surface-mount package, and Figure 22 shows the bottom view
of the surface-mount package. The substrate may only be contacted within the shaded region
between the keep-out outline and the edge of the substrate. The mobile Pentium III processor will
have one or two label marks. These label marks will be located along the long edge of the
substrate outside of the keep-out region and they will not encroach upon the 7-mm by 7-mm
squares at the substrate corners. Please note that in order to implement VID on the BGA2 package,
some VID[4:0] balls may be depopulated.
Table 28. Surface-mount BGA2 Package Specifications
Symbol Parameter Min Max Unit
AOverall Height, as delivered 2.29 2.79 mm
A1Substrate Height, as delivered 1.50 REF mm
A2Die Height 0.854 REF mm
bBall Diameter 0.78 REF mm
DPackage Width 27.05 27.35 mm
D1Die Width D0 Step 8.82 REF (CPUID = 068Ah)
C0 Step 8.82 REF (CPUID = 0686h)
B0 Step 9.28 REF (CPUID = 0683h)
A2 Step 9.37 REF (CPUID = 0681h)
mm
EPackage Length 30.85 31.15 mm
eBall Pitch 1.27 mm
E1Die Length D0 Step 11.00 REF (CPUID = 068Ah)
C0 Step 10.80 REF (CPUID = 0686h)
B0 Step 11.23 REF (CPUID = 0683h)
A2 Step 11.27 REF (CPUID = 0681h)
mm
NBall Count 4951each
S1Outer Ball Center to Short Edge of Substrate 0.895 REF mm
S2Outer Ball Center to Long Edge of Substrate 0.900 REF mm
PDIE Allowable Pressure on the Die for Thermal Solution —689 kPa
WPackage Weight 4.5 REF grams
NOTE: Exact ball count will vary depending on VID[4:0] encoding. See VID[4:0] signal description.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 47
Figure 21. Surface-mount BGA2 Package - Top and Side View
D1
E1
NOTE: All dimensions are in millimeters. Dimensions in figure are for reference only. See Table 28 for specifications.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
48 Datasheet Order Number 283653-001
Figure 22. Surface-mount BGA2 Package - Bottom View
NOTE: All dimensions are in millimeters. Dimensions in figure are for reference only. See Table 28 for specifications
5.2 Socketable Micro-PGA2 Package Dimensions
The mobile Pentium III processor is also packaged in a PPGA-B495 package (also known as
Micro-PGA2) with the back of the processor die exposed on top. Unlike previous mobile
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 49
processors with exposed die, the back of the mobile Pentium III processor die may be polished and
very smooth. The mechanical specifications for the socketable package are provided in Table 29.
Figure 23 shows the top and side views of the socketable package, and Figure 24 shows the
bottom view of the socketable package. The substrate may only be contacted within the region
between the keep-out outline and the edge of the substrate. The mobile Pentium III processor will
have one or two label marks. These label marks will be located along the long edge of the
substrate outside of the keep-out region, and they will not encroach upon the 7-mm by 7-mm
squares at the substrate corners. Unlike the BGA2 package, VID implementation does not require
VID pins to be depopulated on the Micro-PGA2 package.
Table 29. Socketable Micro-PGA2 Package Specification
Symbol Parameter Min Max Unit
AOverall Height, top of die to seating plane of interposer 3.13 3.73 mm
A1Pin Length 1.25 REF mm
A2Die Height 0.854 REF mm
BPin Diameter 0.30 REF mm
D2Package Width 28.27 REF mm
DDie Substrate Width 27.05 27.35 mm
D1Die Width D0 Step 8.82 REF (CPUID = 068Ah)
C0 Step 8.82 REF (CPUID = 0686h)
B0 Step 9.28 REF (CPUID = 0683h)
A2 Step 9.37 REF (CPUID = 0681h)
mm
E2Package Length 34.21 REF mm
EDie Substrate Length 30.85 31.15 mm
E1Die Length D0 Step 11.00 REF (CPUID = 068Ah)
C0 Step 10.80 REF (CPUID = 0686h)
B0 Step 11.23 REF (CPUID = 0683h)
A2 Step 11.27 REF (CPUID = 0681h)
mm
ePin Pitch 1.27 mm
—Pin Tip Radial True Position ≤ 0.127 REF mm
NPin Count 495 each
S1Outer Pin Center to Short Edge of Substrate 2.144 REF mm
S2Outer Pin Center to Long Edge of Substrate 1.206 REF mm
PDIE Allowable Pressure on the Die for Thermal Solution —689 kPa
WPackage Weight 6.2 REF grams
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
50 Datasheet Order Number 283653-001
Figure 23. Socketable Micro-PGA2 Package - Top and Side View
D1
E1
NOTE: All dimensions are in millimeters. Dimensions in figure are for reference only. See Table 29 for
specifications.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 51
Figure 24. Socketable Micro-PGA2 Package - Bottom View
NOTE: All dimensions are in millimeters. Dimensions in figure are for reference only. See Table 29 for
specifications.
5.3 Signal Listings
Figure 25 is a top-side view of the ball or pin map of the mobile Pentium III processor with the
voltage balls/pins called out. Table 30 lists the signals in ball/pin number order. Table 31 lists the
signals in signal name order.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
52 Datasheet Order Number 283653-001
Figure 25. Pin/Ball Map - Top View
V0024-03
VCC OtherVCCT VSS Analog
Decoupling
VSSD30#D21#D23#NCNCNCD10#D14#VSSVSSNCD5#VSSVSSRESET#A33#A32#A29#VSS
D31#D29#D27#VSSD22#D13#VSSD18#D9#D11#D7#VSSD4#VSSVSSVSSVSSA34#A28#A30#VSS
D33#D35#VSSD26#D24#VSSVSSNCD20#D8#VSSD6#VSSD3#D2#BREQ0#A35#A20#A26#A31#A27#
D38#D37#D32#D28#D25#NCD16#NCD15#D17#D1#D0#VSSNCVSSVSSA24#A25#A21#VSSA22#
D45#D43#VSSD34#VREFVREFNCD19#VSSD12#VSSVSSVSSVSSVSSBERR#VREFA15#VSSA23#A19#
D42#VSSVREFA17#VSSA18#A16#
D51#D49#NCTESTPVSSNCA13#
D47#VSSNCTESTPNCVSSA14#
D59#D46#NCVSSA11#A5#A10#
D53#VSSA8#A12#A4#VSSA9#
D55#D60#VSSA6#A3#A7#
D56#VSSNCNCBCLKDEFER#
VSSVSSTESTLO2VSSVSSVSSVSS
DEP5#DEP6#VSSNCNCCLKREF
DEP3#VSSVSSVSSVSSGHI#LOCK#
DEP1#D58#VSSBNR#VSSREQ0#DRDY#
DEP2#VSSVREFBPRI#DEFER#TRDY#RS0#
BINIT#DEP0#PWRGOODREQ1#VSSREQ2#HIT#
BPM0#PRDY#REQ4#VSSREQ3#RP#RS2#
BP3#PICD1TESTLO1HITM#VSSAP1#RSP#
BP2#VSSNCVSSDBSY#RS1#AERR#
PICD0PREQ#VSSVSSADS#AP0#
VSSNCVSSNCVSSVSS
TESTPVID2VID0VSS VSS
212019181716151413121110987654321
PLL2
VSS
VSSNCVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCT
D44#D39#VCCTVCCT
VSSD48#VCCTVCCT
D61#D54#VCCTVCCT
VSSVSSVCCTVCCT
VSSD50#VCCTVCCT
D56#D63#VCCTVCCT
VSSVSSVCCTVCCT
DEP7#D62#VCCTVCCT
VSSDEP4#VCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCT
BPM1#VSSVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCTVCCT
VSSVREFVREFVSSVSSVSSVSSVSSVSSVSSVSSVCCTVCCTVCCT
VSSD41#VCCTVCCT
D57#D52#VCCTVCCT
D36#D40#VREFVSSVSSVSSVSSVSSVSSVSSVSSVSSVSSVSS
NCPICCLKTESTP
EDGE
CTRLP
THERM
DA
TRST#VSSBSEL0TCKINIT#
CMOS
REF
VCCTVCCTVCCT
RSVDINTRVSS
THERM
DC
BSEL1VSSVSSSLP#VSSSMI#VSSVCCTVCCTVCCT
NMIVSSNCVSSTDOVSSIGNNE#FERR#STPCLK#VSSFLUSH#VCCTVCCTVCCT
RTT
IMPEDP
CMOS
REF
TESTHIVSSNCTMSTDINCNCA20M#IERR#VCCTVCCTVCCT
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
VSS VCC VSS VCC VSS VCC
VCC VSS VCC VSS VCC VSS
VSS VCC VSS VCC VSS
VCC VSS VCC VSS VCC
VSS VCC VSS VCC VSS VCC
VCC VSS VCC VSS VCC VSS
VSS VCC VSS VCC VSS VCC
VCC VSS VCC VSS VCC VSS
VCC VSS VCC VSS VCC VSS
VSS VCC VSS VCC VSS VCC
VCC
VSS
VSS VCC
VCC VSS
VSS VCC
VCC VSS
VSS VCC
VCC VSS
VSS VCC
VCC VSS
VCC VSS
VSS VCC
VSS VCC
VCC VSS
VSS VCC
VCC VSS
VSS VCC
VCC VSS
VSS VCC
VCC VSS
VCC VSS
VSS VCC
VID4
VID3
VID1
PLL1
VCC
2
NOTES:
1. In order to implement VID on the BGA2 package, some VID[4:0] balls may be depopulated. However, on
the Micro-PGA2 package, VID[4:0] pins are not depopulated.
2. For any of the following conditions, the pin/ball P1 must be connected to Vcc:
• All processors with a nominal core operating voltage less than 1.35V or greater than 1.60V
• All processors based on any new steppings following C-step
For all other processors based on A2/B0/C0 stepping, the pin/ball P1 can be connected to either Vcc or
Vcct.
Table 30. Signal Listing in Order by Pin/Ball Number
No. Signal Name No. Signal Name No. Signal Name No. Signal Name
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 53
No. Signal Name No. Signal Name No. Signal Name No. Signal Name
A2 VSS C3 A26# E2 A23# G1 A13#
A3 A29# C4 A20# E3 VSS G2 NC
A4 A32# C5 A35# E4 A15# G3 VSS
A5 A33# C6 BREQ0# E5 VREF G4 TESTP
A6 RESET# C7 D2# E6 BERR# G5 NC
A7 VSS C8 D3# E7 VSS G6 VCCT
A8 VSS C9 VSS E8 VSS G7 VCCT
A9 D5# C10 D6# E9 VSS G8 VCCT
A12 VSS C11 VSS E10 VSS G9 VCCT
A13 D14# C12 D8# E11 VSS G10 VCCT
A14 D10# C13 D20# E12 D12# G11 VCCT
A15 NC C14 NC E13 VSS G12 VCCT
A16 NC C15 VSS E14 D19# G13 VCCT
A17 NC C16 VSS E15 NC G14 VCCT
A18 D23# C17 D24# E16 VREF G15 VCCT
A19 D21# C18 D26# E17 VREF G16 VCCT
A20 D30# C19 VSS E18 D34# G17 VCCT
A21 VSS C20 D35# E19 VSS G18 NC
B1 VSS C21 D33# E20 D43# G19 VSS
B2 A30# D1 A22# E21 D45# G20 D49#
B3 A28# D2 VSS F1 A16# G21 D51#
B4 A34# D3 A21# F2 A18# H1 A14#
B5 VSS D4 A25# F3 VSS H2 VSS
B6 VSS D5 A24# F4 A17# H3 NC
B7 VSS D6 VSS F5 VREF H4 TESTP
B8 VSS D7 VSS F6 VSS H5 NC
B9 D4# D8 NC F7 VSS H6 VCCT
B10 VSS D9 VSS F8 VSS H7 VSS
B11 D7# D10 D0# F9 VSS H8 VCC
B12 D11# D11 D1# F10 VSS H9 VSS
B13 D9# D12 D17# F11 VSS H10 VCC
B14 D18# D13 D15# F12 VSS H11 VSS
B15 VSS D14 NC F13 VSS H12 VCC
B16 D13# D15 D16# F14 VSS H13 VSS
B17 D22# D16 NC F15 VSS H14 VCC
B18 VSS D17 D25# F16 VSS H15 VSS
B19 D27# D18 D28# F17 VREF H16 VCC
B20 D29# D19 D32# F18 D40# H17 VCCT
B21 D31# D20 D37# F19 D36# H18 D39#
C1 A27# D21 D38# F20 VSS H19 D44#
C2 A31# E1 A19# F21 D42# H20 VSS
No. Signal Name No. Signal Name No. Signal Name No. Signal Name
H21 D47# K20 VSS M20 VSS R1 LOCK#
J1 A10# K21 D53# N2 VSS R2 GHI#
J2 A5# L1 A7# N3 VSS R3 VSS
J3 A11# L2 PLL1 N4 VSS R4 VSS
J4 VSS L3 A3# N5 TESTLO2 R5 VSS
J5 NC L4 A6# N6 VCCT R6 VCCT
J6 VCCT L5 VSS N7 VCC R7 VCC
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
54 Datasheet Order Number 283653-001
No. Signal Name No. Signal Name No. Signal Name No. Signal Name
J7 VCC L6 VCCT N8 VSS R8 VSS
J8 VSS L7 VCC N9 VCC R9 VCC
J9 VCC L8 VSS N10 VSS R10 VSS
J10 VSS L9 VCC N11 VCC R11 VCC
J11 VCC L10 VSS N12 VSS R12 VSS
J12 VSS L11 VCC N13 VCC R13 VCC
J13 VCC L12 VSS N14 VSS R14 VSS
J14 VSS L13 VCC N15 VCC R15 VCC
J15 VCC L14 VSS N16 VSS R16 VSS
J16 VSS L15 VCC N17 VCCT R17 VCCT
J17 VCCT L16 VSS N18 VSS R18 D63#
J18 D41# L17 VCCT N19 VSS R19 D56#
J19 VSS L18 D48# N20 VSS R20 VSS
J20 D46# L19 VSS P1* VCC R21 DEP3#
J21 D59# L20 D60# P2 CLKREF T1 DRDY#
K1 A9# L21 D55# P3 NC T2 REQ0#
K2 VSS M2 PLL2 P4 NC T3 VSS
K3 A4# M3 BCLK P5 VSS T4 BNR#
K4 A12# M4 NC P6 VCCT T5 VSS
K5 A8# M5 NC P7 VSS T6 VCCT
K6 VCCT M6 VCCT P8 VCC T7 VSS
K7 VSS M7 VSS P9 VSS T8 VCC
K8 VCC M8 VCC P10 VCC T9 VSS
K9 VSS M9 VSS P11 VSS T10 VCC
K10 VCC M10 VCC P12 VCC T11 VSS
K11 VSS M11 VSS P13 VSS T12 VCC
K12 VCC M12 VCC P14 VCC T13 VSS
K13 VSS M13 VSS P15 VSS T14 VCC
K14 VCC M14 VCC P16 VCC T15 VSS
K15 VSS M15 VSS P17 VCCT T16 VCC
K16 VCC M16 VCC P18 D50# T17 VCCT
K17 VCCT M17 VCCT P19 VSS T18 VSS
K18 D52# M18 D54# P20 DEP6# T19 VSS
K19 D57# M19 D61# P21 DEP5# T20 D58#
No. Signal Name No. Signal Name No. Signal Name No. Signal Name
T21 DEP1# V20 DEP0# Y19 VSS AB18 INTR/LINT0
U1 RS0# V21 BINIT# Y20 PICD1 AB19 RSVD
U2 TRDY# W1 RS2# Y21 BP3# AB20 PREQ#
U3 DEFER# W2 RP# AA1 AERR# AB21 PICD0
U4 BPRI# W3 REQ3# AA2 RS1# AC1 VSS
U5 VREF W4 VSS AA3 DBSY# AC2 VSS
U6 VCCT W5 REQ4# AA4 VSS AC3 NC
U7 VCC W6 VCCT AA5 NC AC4 VID3
U8 VSS W7 VCCT AA6 VCCT AC5 VSS
U9 VCC W8 VCCT AA7 VCCT AC6 VCCT
U10 VSS W9 VCCT AA8 VCCT AC7 VCCT
U11 VCC W10 VCCT AA9 CMOSREF AC8 VCCT
U12 VSS W11 VCCT AA10 INIT# AC9 FLUSH#
U13 VCC W12 VCCT AA11 TCK AC10 VSS
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 55
No. Signal Name No. Signal Name No. Signal Name No. Signal Name
U14 VSS W13 VCCT AA12 BSEL0 AC11 STPCLK#
U15 VCC W14 VCCT AA13 VSS AC12 FERR#
U16 VSS W15 VCCT AA14 TRST# AC13 IGNNE#
U17 VCCT W16 VCCT AA15 THERMDA AC14 VSS
U18 D62# W17 VCCT AA16 EDGECTRLP AC15 TDO
U19 DEP7# W18 VSS AA17 TESTP AC16 VSS
U20 VSS W19 BPM1# AA18 PICCLK AC17 NC
U21 DEP2# W20 PRDY# AA19 NC AC18 VSS
V1 HIT# W21 BPM0# AA20 VSS AC19 NMI/LINT1
V2 REQ2# Y1 RSP# AA21 BP2# AC20 NC
V3 VSS Y2 AP1# AB1 AP0# AC21 VSS
V4 REQ1# Y3 VSS AB2 ADS# AD1 VSS
V5 PWRGOOD Y4 HITM# AB3 VSS AD2 VID0
V6 VCCT Y5 TESTLO1 AB4 VID4 AD3 VID1
V7 VCCT Y6 VCCT AB5 VSS AD4 VID2
V8 VCCT Y7 VCCT AB6 VCCT AD5 VSS
V9 VCCT Y8 VCCT AB7 VCCT AD6 VCCT
V10 VCCT Y9 VSS AB8 VCCT AD7 VCCT
V11 VCCT Y10 VSS AB9 VSS AD8 VCCT
V12 VCCT Y11 VSS AB10 SMI# AD9 IERR#
V13 VCCT Y12 VSS AB11 VSS AD10 A20M#
V14 VCCT Y13 VSS AB12 SLP# AD13 TDI
V15 VCCT Y14 VSS AB13 VSS AD14 TMS
V16 VCCT Y15 VSS AB14 VSS AD15 NC
V17 VCCT Y16 VSS AB15 BSEL1 AD16 VSS
V18 DEP4# Y17 VREF AB16 THERMDC AD17 TESTHI
V19 VSS Y18 VREF AB17 VSS AD18 CMOSREF
No. Signal Name No. Signal Name No. Signal Name No. Signal Name
AD19 RTTIMPEDP AD20 TESTP AD21 VSS
NOTES:
1. * For any of the following conditions, the pin/ball P1 must be connected to Vcc:
• All processors with a nominal core operating voltage less than 1.35V or greater than 1.60V
• All processors based on any new steppings following C-step
2. For all other processors based on A2/B0/C0 stepping, the pin/ball P1 can be connected to either Vcc or
Vcct.
Table 31. Signal Listing in Order by Signal Name
No. Signal Name Signal Buffer Type No. Signal Name Signal Buffer Type
L3 A3# GTL+ I/O T4 BNR# GTL+ I/O
K3 A4# GTL+ I/O AA21 BP2# GTL+ I/O
J2 A5# GTL+ I/O Y21 BP3# GTL+ I/O
L4 A6# GTL+ I/O W21 BPM0# GTL+ I/O
L1 A7# GTL+ I/O W19 BPM1# GTL+ I/O
K5 A8# GTL+ I/O U4 BPRI# GTL+ Input
K1 A9# GTL+ I/O C6 BREQ0# GTL+ I/O
J1 A10# GTL+ I/O AA12 BSEL0 3.3V CMOS Input
J3 A11# GTL+ I/O AB15 BSEL1 3.3V CMOS Input
K4 A12# GTL+ I/O P2 CLKREF BCLK Reference Voltage
G1 A13# GTL+ I/O AA9 CMOSREF CMOS Reference Voltage
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
56 Datasheet Order Number 283653-001
H1 A14# GTL+ I/O AD18 CMOSREF CMOS Reference Voltage
E4 A15# GTL+ I/O D10 D0# GTL+ I/O
F1 A16# GTL+ I/O D11 D1# GTL+ I/O
F4 A17# GTL+ I/O C7 D2# GTL+ I/O
F2 A18# GTL+ I/O C8 D3# GTL+ I/O
E1 A19# GTL+ I/O B9 D4# GTL+ I/O
C4 A20# GTL+ I/O A9 D5# GTL+ I/O
D3 A21# GTL+ I/O C10 D6# GTL+ I/O
D1 A22# GTL+ I/O B11 D7# GTL+ I/O
E2 A23# GTL+ I/O C12 D8# GTL+ I/O
D5 A24# GTL+ I/O B13 D9# GTL+ I/O
D4 A25# GTL+ I/O A14 D10# GTL+ I/O
C3 A26# GTL+ I/O B12 D11# GTL+ I/O
C1 A27# GTL+ I/O E12 D12# GTL+ I/O
B3 A28# GTL+ I/O B16 D13# GTL+ I/O
A3 A29# GTL+ I/O A13 D14# GTL+ I/O
B2 A30# GTL+ I/O D13 D15# GTL+ I/O
C2 A31# GTL+ I/O D15 D16# GTL+ I/O
A4 A32# GTL+ I/O D12 D17# GTL+ I/O
A5 A33# GTL+ I/O B14 D18# GTL+ I/O
B4 A34# GTL+ I/O E14 D19# GTL+ I/O
C5 A35# GTL+ I/O C13 D20# GTL+ I/O
AD10 A20M# 1.5V CMOS Input A19 D21# GTL+ I/O
AB2 ADS# GTL+ I/O B17 D22# GTL+ I/O
AA1 AERR# GTL+ I/O A18 D23# GTL+ I/O
AB1 AP0# GTL+ I/O C17 D24# GTL+ I/O
Y2 AP1# GTL+ I/O D17 D25# GTL+ I/O
M3 BCLK 2.5V Clock Input C18 D26# GTL+ I/O
E6 BERR# GTL+ I/O B19 D27# GTL+ I/O
V21 BINIT# GTL+ I/O D18 D28# GTL+ I/O
No. Signal Name Signal Buffer Type No. Signal Name Signal Buffer Type
B20 D29# GTL+ I/O V18 DEP4# GTL+ I/O
A20 D30# GTL+ I/O P21 DEP5# GTL+ I/O
B21 D31# GTL+ I/O P20 DEP6# GTL+ I/O
D19 D32# GTL+ I/O U19 DEP7# GTL+ I/O
C21 D33# GTL+ I/O T1 DRDY# GTL+ I/O
E18 D34# GTL+ I/O AA16 EDGECTRLP GTL+ Control
C20 D35# GTL+ I/O AC12 FERR# 1.5V Open Drain Output
F19 D36# GTL+ I/O AC9 FLUSH# 1.5V CMOS Input
D20 D37# GTL+ I/O V1 HIT# GTL+ I/O
D21 D38# GTL+ I/O Y4 HITM# GTL+ I/O
H18 D39# GTL+ I/O AD9 IERR# 1.5V Open Drain Output
F18 D40# GTL+ I/O AC13 IGNNE# 1.5V CMOS Input
J18 D41# GTL+ I/O AA10 INIT# 1.5V CMOS Input
F21 D42# GTL+ I/O AB18 INTR/LINT0 1.5V CMOS Input
E20 D43# GTL+ I/O R1 LOCK# GTL+ I/O
H19 D44# GTL+ I/O AC19 NMI/LINT1 1.5V CMOS Input
E21 D45# GTL+ I/O AA18 PICCLK 2.5V APIC Clock Input
J20 D46# GTL+ I/O AB21 PICD0 1.5V Open Drain I/O
H21 D47# GTL+ I/O Y20 PICD1 1.5V Open Drain I/O
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 57
L18 D48# GTL+ I/O L2 PLL1 PLL Analog Voltage
G20 D49# GTL+ I/O M2 PLL2 PLL Analog Voltage
P18 D50# GTL+ I/O W20 PRDY# GTL+ Output
G21 D51# GTL+ I/O AB20 PREQ# 1.5V CMOS Input
K18 D52# GTL+ I/O V5 PWRGOOD 2.5V CMOS Input
K21 D53# GTL+ I/O T2 REQ0# GTL+ I/O
M18 D54# GTL+ I/O V4 REQ1# GTL+ I/O
L21 D55# GTL+ I/O V2 REQ2# GTL+ I/O
R19 D56# GTL+ I/O W3 REQ3# GTL+ I/O
K19 D57# GTL+ I/O W5 REQ4# GTL+ I/O
T20 D58# GTL+ I/O U1 RS0# GTL+ Input
J21 D59# GTL+ I/O A6 RESET# GTL+ Input
L20 D60# GTL+ I/O W2 RP# GTL+ I/O
M19 D61# GTL+ I/O AA2 RS1# GTL+ Input
U18 D62# GTL+ I/O W1 RS2# GTL+ Input
R18 D63# GTL+ I/O Y1 RSP# GTL+ Input
AA3 DBSY# GTL+ I/O R2 GHI# 1.5V CMOS Input
U3 DEFER# GTL+ Input AB19 RSVD Reserved
V20 DEP0# GTL+ I/O AD19 RTTIMPEDP GTL+ Pull-up Control
T21 DEP1# GTL+ I/O AB12 SLP# 1.5V CMOS Input
U21 DEP2# GTL+ I/O AB10 SMI# 1.5V CMOS Input
R21 DEP3# GTL+ I/O AC11 STPCLK# 1.5V CMOS Input
No. Signal Name Signal Buffer Type No. Signal Name Signal Buffer Type
AA11 TCK 1.5V JTAG Clock Input AA14 TRST# JTAG Input
AD13 TDI JTAG Input AD2 VID0 Voltage Identification
AC15 TDO JTAG Output AD3 VID1 Voltage Identification
AD17 TESTHI Test Input AD4 VID2 Voltage Identification
Y5 TESTLO1 Test Input AC4 VID3 Voltage Identification
N5 TESTLO2 Test Input AB4 VID4 Voltage Identification
AD20 TESTP Core Voltage Test Point E5 VREF GTL+ Reference Voltage
H4 TESTP Core Voltage Test Point E16 VREF GTL+ Reference Voltage
AA17 TESTP Core Voltage Test Point E17 VREF GTL+ Reference Voltage
G4 TESTP Core Voltage Test Point F5 VREF GTL+ Reference Voltage
AA15 THERMDA Thermal Diode Anode F17 VREF GTL+ Reference Voltage
AB16 THERMDC Thermal Diode Cathode U5 VREF GTL+ Reference Voltage
AD14 TMS JTAG Input Y17 VREF GTL+ Reference Voltage
U2 TRDY# GTL+ Input Y18 VREF GTL+ Reference Voltage
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
58 Datasheet Order Number 283653-001
Table 32. Voltage and No-Connect Pin/Ball Locations
Signal
Name Pin/Ball Numbers
NC A15, A16, A17, C14, D8, D14, D16, E15, G2, G5, G18, H3, H5, J5, M4, M5, P3, P4, AA5, AA19, AC3, AC17,
AC20, AD15
VCC H8, H10, H12, H14, H16, J7, J9, J11, J13, J15, K8, K10, K12, K14, K16, L7, L9, L11, L13, L15, M8, M10, M12,
M14, M16, N7, N9, N11, N13, N15, P1*, P8, P10, P12, P14, P16, R7, R9, R11, R13, R15, T8, T10, T12, T14,
T16, U7, U9, U11, U13, U15
VCCT G6, G7, G8, G9, G10, G11, G12, G13, G14, G15, G16, G17, H6, H17, J6, J17, K6, K17, L6, L17, M6, M17,
N6, N17, P1*, P6, P17, R6, R17, T6, T17, U6, U17, V6, V7, V8, V9, V10, V11, V12, V13, V14, V15, V16, V17,
W6, W7, W8, W9, W10, W11, W12, W13, W14, W15, W16, W17, Y6, Y7, Y8, AA6, AA7, AA8, AB6, AB7, AB8,
AC6, AC7, AC8, AD6, AD7, AD8
VSS A2, A7, A8, A12, A21, B1, B5, B6, B7, B8, B10, B15, B18, C9, C11, C15, C16, C19, D2, D6, D7, D9, E3, E7,
E8, E9, E10, E11, E13, E19, F3, F6, F7, F8, F9, F10, F11, F12, F13, F14, F15, F16, F20, G3, G19, H2, H7,
H9, H11, H13, H15, H20, J4, J8, J10, J12, J14, J16, J19, K2, K7, K9, K11, K13, K15, K20, L5, L8, L10, L12,
L14, L16, L19, M7, M9, M11, M13, M15, M20, N2, N3, N4, N8, N10, N12, N14, N16, N18, N19, N20, P5, P7,
P9, P11, P13, P15, P19, R3, R4, R5, R8, R10, R12, R14, R16, R20, T3, T5, T7, T9, T11, T13, T15, T18, T19,
U8, U10, U12, U14, U16, U20, V3, V19, W4, W18, Y3, Y9, Y10, Y11, Y12, Y13, Y14, Y15, Y16, Y19, AA4,
AA13, AA20, AB3, AB5, AB9, AB11, AB13, AB14, AB17, AC1, AC2, AC5, AC10, AC14, AC16, AC18, AC21,
AD1, AD5, AD16, AD21
NOTES:
1. * For any of the following conditions, the pin/ball P1 must be connected to Vcc:
• All processors with a nominal core operating voltage less than 1.35V or greater than 1.60V
• All processors based on any new steppings following C-step
2. For all other processors based on A2/B0/C0 stepping, the pin/ball P1 can be connected to either Vcc or
Vcct.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 59
6. Thermal Specifications
This chapter provides needed data for designing a thermal solution. The mobile Pentium III
processor is either a surface mount PBGA-B495 package or a socketable PPGA-B495 package
with the back of the processor die exposed and has a specified operational junction temperature
(TJ) limit.
In order to achieve proper cooling of the processor, a thermal solution (e.g., heat spreader, heat
pipe, or other heat transfer system) must make firm contact to the exposed processor die. The
processor die must be clean before the thermal solution is attached or the processor may be
damaged.
Table 33 provides the maximum Thermal Design Power (TDPMAX) dissipation and the minimum
and maximum TJ temperatures for the mobile Pentium III processor. A thermal solution should be
designed to ensure the junction temperature never exceeds these specifications. If no closed loop
thermal failsafe mechanism (processor throttling) is present to maintain TJ within specification
then the thermal solution should be designed to cool the TDPMAX condition. If a thermal failsafe
mechanism is present then thermal solution could possibly be designed to a typical Thermal
Design Power (TDPTYP). TDPTYP is a thermal design power recommendation based on the power
dissipation of the processor while executing publicly available software under normal operating
conditions at nominal voltages. TDPTYP power is lower than TDPMAX. Contact your Intel Field
Sales Representative for further information.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
60 Datasheet Order Number 283653-001
Table 33. Power Specifications for Mobile Pentium III Processor with Intel SpeedStep Technology
Symbol Parameter TDP Typ1,3 TDP Max2,3 PSGNT3,4 PQS3,5 PDSLP3,6 Unit
Power 500 / 300 MHz & 1.10 / 0.975V
600 / 300 MHz & 1.10 / 0.975V
600 / 500 MHz & 1.35 / 1.10V
700 / 500 MHz & 1.35 / 1.10V
750 / 500 MHz & 1.35 / 1.10V
700 / 550 MHz & 1.60 / 1.35V
750 / 600 MHz & 1.60 / 1.35V
800 / 650 MHz & 1.60 / 1.35V
850 / 700 MHz & 1.60 / 1.35V
900 / 700 MHz & 1.70 / 1.35V
1GHz / 700 MHz & 1.70 / 1.35V
5.0 / 2.4
6.4 / 2.4
8.7 / 5.0
10.2 / 5.0
12.4 / 5.0
15.0 / 8.5
15.8 / 8.7
17.0 / 9.5
18.2 / 10.2
23.3 / 11.2
24.8 / 11.2
8.1 / 4.5
9.7 / 4.5
14.4 / 8.1
16.1 / 8.1
17.2 / 8.1
23.0 / 13.2
24.6 / 14.4
25.9 / 15.1
27.5 / 16.1
30.7 / 16.1
34.0 / 16.1
0.8 / 0.6
0.8 / 0.6
1.1 / 0.8
1.6 / 0.8
1.6 / 0.8
1.7 / 1.1
1.7 / 1.1
2.7 / 1.6
2.7 / 1.6
2.9 / 1.6
2.9 / 1.6
0.6 / 0.5
0.6 / 0.5
0.8 / 0.6
1.2 / 0.6
1.2 / 0.6
1.3 / 0.8
1.3 / 0.8
1.9 / 1.2
1.9 / 1.2
2.2 / 1.2
2.2 / 1.2
0.2 / 0.2
0.2 / 0.2
0.3 / 0.2
0.4 / 0.2
0.4 / 0.2
0.5 / 0.3
0.5 / 0.3
0.75 / 0.4
0.75 / 0.4
0.93 / 0.4
0.93 / 0.4
W
W
W
W
W
W
W
W
W
W
W
TJ Junction temperature is
measured with the on-die
thermal diode
927, 100 927, 100 50 50 35 °C
NOTES:
1. TDPTYP (Thermal Design Power) is a recommendation based on the power dissipation of the processor while executing
publicly available software under normal operating conditions at nominal voltages. Not 100% tested.
2. TDPMAX is a specification of the total power dissipation of the processor while executing a worst-case instruction mix
under normal operating conditions at nominal voltages. It includes the power dissipated by all of the components within
the processor. Not 100% tested. Specified by design/characterization.
3. Not 100% tested or guaranteed. The power specifications are composed of the current of the processor on the various
voltage planes. These currents are measured and specified at high temperature in Table 9B. These power
specifications are determined by characterization of the processor currents at higher temperatures.
4. PSGNT is Stop Grant and Auto Halt power.
5. PQS is Quick Start and Sleep power.
6. PDSLP is Deep Sleep power.
7. 1GHz/700 MHz product also available with junction temperature (Tj) of 92°C. S-Spec number on the package will
identify the part.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 61
6.1 Thermal Diode
The mobile Pentium III processor has an on-die thermal diode that can be used to monitor the die
temperature(TJ). A thermal sensor located on the motherboard, or a stand-alone measurement kit,
may monitor the die temperature of the processor for thermal management or instrumentation
purposes. Table 34 and Table 35 provide the diode interface and specifications.
Note: The reading of the thermal sensor connected to the thermal diode will not necessarily reflect the
temperature of the hottest location on the die. This is due to inaccuracies in the thermal sensor, on-
die temperature gradients between the location of the thermal diode and the hottest location on the
die, and time based variations in the die temperature measurement. Time based variations can
occur when the sampling rate of the thermal diode (by the thermal sensor) is slower than the rate at
which the TJ temperature can change.
Table 34. Thermal Diode Interface
Signal Name Pin/Ball Number Signal Description
THERMDA AA15 Thermal diode anode
THERMDC AB16 Thermal diode cathode
Table 35. Thermal Diode Specifications
Symbol Parameter Min Typ Max Unit Notes
IFW Forward Bias Current 5500 µANote 1
nDiode Ideality Factor 1.0057 1.0080 1.0125 Notes 2, 3, 4
NOTES:
1. Intel does not support or recommend operation of the thermal diode under reverse bias. Intel does not support or
recommend operation of the thermal diode when the processor power supplies are not within their specified tolerance
range.
2. Characterized at 100°C.
3. Not 100% tested. Specified by design/characterization.
4. The ideality factor, n, represents the deviation from ideal diode behavior as exemplified by the diode equation: Where Is
= saturation current, q = electronic charge, Vd = voltage across the diode, k = Boltzmann Constant, and T = absolute
temperature (Kelvin).
−⋅=1
q
SFW nkT
VD
eII
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
62 Datasheet Order Number 283653-001
7. Processor Initialization and Configuration
7.1 Description
The mobile Pentium III processor has some configuration options that are determined by hardware
and some that are determined by software. The processor samples its hardware configuration at
reset on the active-to-inactive transition of RESET#. Most of the configuration options for the
mobile Pentium III processor are identical to those of the Pentium II processor. The Pentium® II
Processor Developer’s Manual describes these configuration options. New configuration options
for the mobile Pentium III processor are described in the remainder of this section.
7.1.1 Quick Start Enable
The processor normally enters the Stop Grant state when the STPCLK# signal is asserted but it
will enter the Quick Start state instead if A15# is sampled active on the RESET# signal’s active-
to-inactive transition. The Quick Start state supports snoops from the bus priority device like the
Stop Grant state but it does not support symmetric master snoops nor is the latching of interrupts
supported. A “1” in bit position 5 of the Power-on Configuration register indicates that the Quick
Start state has been enabled.
7.1.2 System Bus Frequency
The current generation mobile Pentium III processor will only function with a system bus
frequency of 100 MHz. Bit positions 18 to 19 of the Power-on Configuration register indicates at
which speed a processor will run. A “00” in bits [19:18] indicates a 66-MHz bus frequency, a “10”
indicates a 100-MHz bus frequency, and a “01” indicates a 133-MHz bus frequency.
7.1.3 APIC Enable
If the PICD0 signal is sampled low on the active-to-inactive transition of the RESET# signal then
the PICCLK signal can be tied to VSS. Otherwise the PICD[1:0] signals must be pulled up to VCCT
and PICCLK must be supplied. Driving PICD0 low at reset also has the effect of clearing the
APIC Global Enable bit in the APIC Base MSR. This bit is normally set when the processor is
reset, but when it is cleared the APIC is completely disabled until the next reset.
7.2 Clock Frequencies and Ratios
The mobile Pentium III processor uses a clock design in which the bus clock is multiplied by a
ratio to produce the processor’s internal (or “core”) clock. Unlike some of the mobile Pentium II
processors, the ratio used is programmed into the processor during manufacturing. The bus ratio
programmed into the processor is visible in bit positions 22 to 25 and bit 27 of the Power-on
Configuration register. Table 14 shows the 5-bit codes in the Power-on Configuration register and
their corresponding bus ratios.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 63
8. Processor Interface
8.1 Alphabetical Signal Reference
A[35:3]# (I/O - GTL+)
The A[35:3]# (Address) signals define a 236-byte physical memory address space. When ADS# is
active, these signals transmit the address of a transaction; when ADS# is inactive, these signals
transmit transaction information. These signals must be connected to the appropriate pins/balls of
both agents on the system bus. The A[35:24]# signals are protected with the AP1# parity signal,
and the A[23:3]# signals are protected with the AP0# parity signal.
On the active-to-inactive transition of RESET#, each processor bus agent samples A[35:3]#
signals to determine its power-on configuration. See Section 4 of this document and the Pentium®
II Processor Developer’s Manual for details.
A20M# (I - 1.5V Tolerant)
If the A20M# (Address-20 Mask) input signal is asserted, the processor masks physical address bit
20 (A20#) before looking up a line in any internal cache and before driving a read/write
transaction on the bus. Asserting A20M# emulates the 8086 processor's address wrap-around at
the 1-Mbyte boundary. Assertion of A20M# is only supported in Real mode.
ADS# (I/O - GTL+)
The ADS# (Address Strobe) signal is asserted to indicate the validity of a transaction address on
the A[35:3]# signals. Both bus agents observe the ADS# activation to begin parity checking,
protocol checking, address decode, internal snoop or deferred reply ID match operations
associated with the new transaction. This signal must be connected to the appropriate pins/balls on
both agents on the system bus.
AERR# (I/O - GTL+)
The AERR# (Address Parity Error) signal is observed and driven by both system bus agents, and
if used, must be connected to the appropriate pins/balls of both agents on the system bus. AERR#
observation is optionally enabled during power-on configuration; if enabled, a valid assertion of
AERR# aborts the current transaction.
If AERR# observation is disabled during power-on configuration, a central agent may handle an
assertion of AERR# as appropriate to the error handling architecture of the system.
AP[1:0]# (I/O - GTL+)
The AP[1:0]# (Address Parity) signals are driven by the request initiator along with ADS#,
A[35:3]#, REQ[4:0]# and RP#. AP1# covers A[35:24]#. AP0# covers A[23:3]#. A correct parity
signal is high if an even number of covered signals are low and low if an odd number of covered
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
64 Datasheet Order Number 283653-001
signals are low. This allows parity to be high when all the covered signals are high. AP[1:0]#
should be connected to the appropriate pins/balls on both agents on the system bus.
BCLK (I - 2.5V Tolerant)
The BCLK (Bus Clock) signal determines the system bus frequency. Both system bus agents must
receive this signal to drive their outputs and latch their inputs on the BCLK rising edge. All
external timing parameters are specified with respect to the BCLK signal.
BERR# (I/O - GTL+)
The BERR# (Bus Error) signal is asserted to indicate an unrecoverable error without a bus
protocol violation. It may be driven by either system bus agent and must be connected to the
appropriate pins/balls of both agents, if used. However, the mobile Pentium III processors do not
observe assertions of the BERR# signal.
BERR# assertion conditions are defined by the system configuration. Configuration options
enable the BERR# driver as follows:
• Enabled or disabled
• Asserted optionally for internal errors along with IERR#
• Asserted optionally by the request initiator of a bus transaction after it observes an error
• Asserted by any bus agent when it observes an error in a bus transaction
BINIT# (I/O - GTL+)
The BINIT# (Bus Initialization) signal may be observed and driven by both system bus agents and
must be connected to the appropriate pins/balls of both agents, if used. If the BINIT# driver is
enabled during the power-on configuration, BINIT# is asserted to signal any bus condition that
prevents reliable future information.
If BINIT# is enabled during power-on configuration, and BINIT# is sampled asserted, all bus state
machines are reset and any data which was in transit is lost. All agents reset their rotating ID for
bus arbitration to the state after reset, and internal count information is lost. The L1 and L2 caches
are not affected.
If BINIT# is disabled during power-on configuration, a central agent may handle an assertion of
BINIT# as appropriate to the Machine Check Architecture (MCA) of the system.
BNR# (I/O - GTL+)
The BNR# (Block Next Request) signal is used to assert a bus stall by any bus agent that is unable
to accept new bus transactions. During a bus stall, the current bus owner cannot issue any new
transactions.
Since multiple agents may need to request a bus stall simultaneously, BNR# is a wired-OR signal
that must be connected to the appropriate pins/balls of both agents on the system bus. In order to
avoid wire-OR glitches associated with simultaneous edge transitions driven by multiple drivers,
BNR# is activated on specific clock edges and sampled on specific clock edges.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 65
BP[3:2]# (I/O - GTL+)
The BP[3:2]# (Breakpoint) signals are the System Support group Breakpoint signals. They are
outputs from the processor that indicate the status of breakpoints.
BPM[1:0]# (I/O - GTL+)
The BPM[1:0]# (Breakpoint Monitor) signals are breakpoint and performance monitor signals.
They are outputs from the processor that indicate the status of breakpoints and programmable
counters used for monitoring processor performance.
BPRI# (I - GTL+)
The BPRI# (Bus Priority Request) signal is used to arbitrate for ownership of the system bus. It
must be connected to the appropriate pins/balls on both agents on the system bus. Observing
BPRI# active (as asserted by the priority agent) causes the processor to stop issuing new requests,
unless such requests are part of an ongoing locked operation. The priority agent keeps BPRI#
asserted until all of its requests are completed and then releases the bus by deasserting BPRI#.
BREQ0# (I/O - GTL+)
The BREQ0# (Bus Request) signal is a processor Arbitration Bus signal. The processor indicates
that it wants ownership of the system bus by asserting the BREQ0# signal.
During power-up configuration, the central agent must assert the BREQ0# bus signal. The
processor samples BREQ0# on the active-to-inactive transition of RESET#. Optionally, this signal
may be grounded with a 10ohm resistor.
BSEL[1:0] (I – 3.3V Tolerant)
The BSEL[1:0] (Select Processor System Bus Speed) signal is used to configure the processor for
the system bus frequency. Table 36 shows the encoding scheme for BSEL[1:0]. The only
supported system bus frequency for the mobile Pentium III processor is 100 MHz. If another
frequency is used or if the BSEL[1:0] signals are not driven with “01” then the processor is not
guaranteed to function properly.
Table 36. BSEL[1:0] Encoding
BSEL[1:0] System Bus Frequency
00 66 MHz
01 100 MHz
10 Reserved
11 133 MHz
CLKREF (Analog)
The CLKREF (System Bus Clock Reference) signal provides a reference voltage to define the trip
point for the BCLK signal. This signal should be connected to a resistor divider to generate 1.25V
from the 2.5-V supply.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
66 Datasheet Order Number 283653-001
CMOSREF (Analog)
The CMOSREF (CMOS Reference Voltage) signal provides a DC level reference voltage for the
CMOS input buffers. A voltage divider should be used to divide a stable voltage plane (e.g., 2.5V
or 3.3V). This signal must be provided with a DC voltage that meets the VCMOSREF specification
from Table 12.
D[63:0]# (I/O - GTL+)
The D[63:0]# (Data) signals are the data signals. These signals provide a 64-bit data path between
both system bus agents, and must be connected to the appropriate pins/balls on both agents. The
data driver asserts DRDY# to indicate a valid data transfer.
DBSY# (I/O - GTL+)
The DBSY# (Data Bus Busy) signal is asserted by the agent responsible for driving data on the
system bus to indicate that the data bus is in use. The data bus is released after DBSY# is
deasserted. This signal must be connected to the appropriate pins/balls on both agents on the
system bus.
DEFER# (I - GTL+)
The DEFER# (Defer) signal is asserted by an agent to indicate that the transaction cannot be
guaranteed in-order completion. Assertion of DEFER# is normally the responsibility of the
addressed memory agent or I/O agent. This signal must be connected to the appropriate pins/balls
on both agents on the system bus.
DEP[7:0]# (I/O - GTL+)
The DEP[7:0]# (Data Bus ECC Protection) signals provide optional ECC protection for the data
bus. They are driven by the agent responsible for driving D[63:0]#, and must be connected to the
appropriate pins/balls on both agents on the system bus if they are used. During power-on
configuration, DEP[7:0]# signals can be enabled for ECC checking or disabled for no checking.
DRDY# (I/O - GTL+)
The DRDY# (Data Ready) signal is asserted by the data driver on each data transfer, indicating
valid data on the data bus. In a multi-cycle data transfer, DRDY# can be deasserted to insert idle
clocks. This signal must be connected to the appropriate pins/balls on both agents on the system
bus.
EDGCTRLP (Analog)
The EDGCTRLP (Edge Rate Control) signal is used to configure the edge rate of the GTL+ output
buffers. Connect the signal to VSS with a 110-Ω, 1% resistor.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 67
FERR# (O - 1.5V Tolerant Open-drain)
The FERR# (Floating-point Error) signal is asserted when the processor detects an unmasked
floating-point error. FERR# is similar to the ERROR# signal on the Intel 387 coprocessor, and it
is included for compatibility with systems using DOS-type floating-point error reporting.
FLUSH# (I - 1.5V Tolerant)
When the FLUSH# (Flush) input signal is asserted, the processor writes back all internal cache
lines in the Modified state and invalidates all internal cache lines. At the completion of a flush
operation, the processor issues a Flush Acknowledge transaction. The processor stops caching any
new data while the FLUSH# signal remains asserted.
On the active-to-inactive transition of RESET#, each processor bus agent samples FLUSH# to
determine its power-on configuration.
GHI# (I - 1.5V Tolerant)
The GHI# signal controls which operating mode bus ratio is selected in a mobile Pentium III
processor featuring Intel SpeedStep technology. On the processor featuring Intel SpeedStep
technology, this signal is latched when BCLK restarts in Deep Sleep state and determines which
of two bus ratios is selected for operation. This signal is ignored when the processor is not in the
Deep Sleep state. This signal is a “Don’t Care” on processors that do not feature Intel SpeedStep
technology. This signal has an on-die pull-up to VCCT and should be driven with an Open-drain
driver with no external pull-up.
HIT# (I/O - GTL+), HITM# (I/O - GTL+)
The HIT# (Snoop Hit) and HITM# (Hit Modified) signals convey transaction snoop operation
results, and must be connected to the appropriate pins/balls on both agents on the system bus.
Either bus agent can assert both HIT# and HITM# together to indicate that it requires a snoop
stall, which can be continued by reasserting HIT# and HITM# together.
IERR# (O - 1.5V Tolerant Open-drain)
The IERR# (Internal Error) signal is asserted by the processor as the result of an internal error.
Assertion of IERR# is usually accompanied by a SHUTDOWN transaction on the system bus.
This transaction may optionally be converted to an external error signal (e.g., NMI) by system
logic. The processor will keep IERR# asserted until it is handled in software or with the assertion
of RESET#, BINIT, or INIT#.
IGNNE# (I - 1.5V Tolerant)
The IGNNE# (Ignore Numeric Error) signal is asserted to force the processor to ignore a numeric
error and continue to execute non-control floating-point instructions. If IGNNE# is deasserted, the
processor freezes on a non-control floating-point instruction if a previous instruction caused an
error. IGNNE# has no affect when the NE bit in control register 0 (CR0) is set.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
68 Datasheet Order Number 283653-001
INIT# (I - 1.5V Tolerant)
The INIT# (Initialization) signal is asserted to reset integer registers inside the processor without
affecting the internal (L1 or L2) caches or the floating-point registers. The processor begins
execution at the power-on reset vector configured during power-on configuration. The processor
continues to handle snoop requests during INIT# assertion. INIT# is an asynchronous input.
If INIT# is sampled active on RESET#'s active-to-inactive transition, then the processor executes
its built-in self test (BIST).
INTR (I - 1.5V Tolerant)
The INTR (Interrupt) signal indicates that an external interrupt has been generated. INTR becomes
the LINT0 signal when the APIC is enabled. The interrupt is maskable using the IF bit in the
EFLAGS register. If the IF bit is set, the processor vectors to the interrupt handler after
completing the current instruction execution. Upon recognizing the interrupt request, the processor
issues a single Interrupt Acknowledge (INTA) bus transaction. INTR must remain active until the
INTA bus transaction to guarantee its recognition.
LINT[1:0] (I - 1.5V Tolerant)
The LINT[1:0] (Local APIC Interrupt) signals must be connected to the appropriate pins/balls of
all APIC bus agents, including the processor and the system logic or I/O APIC component. When
APIC is disabled, the LINT0 signal becomes INTR, a maskable interrupt request signal, and
LINT1 becomes NMI, a non-maskable interrupt. INTR and NMI are backward compatible with
the same signals for the Pentium processor. Both signals are asynchronous inputs.
Both of these signals must be software configured by programming the APIC register space to be
used either as NMI/INTR or LINT[1:0] in the BIOS. If the APIC is enabled at reset, then
LINT[1:0] is the default configuration.
LOCK# (I/O - GTL+)
The LOCK# (Lock) signal indicates to the system that a sequence of transactions must occur
atomically. This signal must be connected to the appropriate pins/balls on both agents on the
system bus. For a locked sequence of transactions, LOCK# is asserted from the beginning of the
first transaction through the end of the last transaction.
When the priority agent asserts BPRI# to arbitrate for bus ownership, it waits until it observes
LOCK# deasserted. This enables the processor to retain bus ownership throughout the bus locked
operation and guarantee the atomicity of lock.
NMI (I - 1.5V Tolerant)
The NMI (Non-Maskable Interrupt) indicates that an external interrupt has been generated. NMI
becomes the LINT1 signal when the APIC is disabled. Asserting NMI causes an interrupt with an
internally supplied vector value of 2. An external interrupt-acknowledge transaction is not
generated. If NMI is asserted during the execution of an NMI service routine, it remains pending
and is recognized after the IRET is executed by the NMI service routine. At most, one assertion of
NMI is held pending. NMI is rising edge sensitive.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 69
PICCLK (I - 2.5V Tolerant)
The PICCLK (APIC Clock) signal is an input clock to the processor and system logic or I/O APIC
that is required for operation of the processor, system logic, and I/O APIC components on the
APIC bus.
PICD[1:0] (I/O - 1.5V Tolerant Open-drain)
The PICD[1:0] (APIC Data) signals are used for bi-directional serial message passing on the APIC
bus. They must be connected to the appropriate pins/balls of all APIC bus agents, including the
processor and the system logic or I/O APIC components. If the PICD0 signal is sampled low on
the active-to-inactive transition of the RESET# signal, then the APIC is hardware disabled.
PLL1, PLL2 (Analog)
The PLL1 and PLL2 signals provide isolated analog decoupling is required for the internal PLL.
See Section 3.2.2 for a description of the analog decoupling circuit.
PRDY# (O - GTL+)
The PRDY# (Probe Ready) signal is a processor output used by debug tools to determine
processor debug readiness.
PREQ# (I - 1.5V Tolerant)
The PREQ# (Probe Request) signal is used by debug tools to request debug operation of the
processor.
PWRGOOD (I - 2.5V Tolerant)
PWRGOOD (Power Good) is a 2.5-V tolerant input. The processor requires this signal to be a
clean indication that clocks and the power supplies (VCC, VCCT, etc.) are stable and within their
specifications. Clean implies that the signal will remain low, (capable of sinking leakage current)
and without glitches, from the time that the power supplies are turned on, until they come within
specification. The signal will then transition monotonically to a high (2.5V) state. Figure 26
illustrates the relationship of PWRGOOD to other system signals. PWRGOOD can be driven
inactive at any time, but clocks and power must again be stable before the rising edge of
PWRGOOD. It must also meet the minimum pulse width specified in Table 16 (Section 3.7) and
be followed by a 1 ms RESET# pulse.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
70 Datasheet Order Number 283653-001
Figure 26. PWRGOOD Relationship at Power On
BCLK
PWRGOOD
RESET#
D0026-01
1 msec
V
IH25,min
VCC,
VCCT,
VREF
The PWRGOOD signal, which must be supplied to the processor, is used to protect internal
circuits against voltage sequencing issues. The PWRGOOD signal should be driven high
throughout boundary scan operation.
REQ[4:0]# (I/O - GTL+)
The REQ[4:0]# (Request Command) signals must be connected to the appropriate pins/balls on
both agents on the system bus. They are asserted by the current bus owner when it drives A[35:3]#
to define the currently active transaction type.
RESET# (I - GTL+)
Asserting the RESET# signal resets the processor to a known state and invalidates the L1 and L2
caches without writing back Modified (M state) lines. For a power-on type reset, RESET# must
stay active for at least 1 msec after VCC and BCLK have reached their proper DC and AC
specifications and after PWRGOOD has been asserted. When observing active RESET#, all bus
agents will deassert their outputs within two clocks. RESET# is the only GTL+ signal that does
not have on-die GTL+ termination. A 56.2Ω 1% terminating resistor connected to VCCT is
required.
A number of bus signals are sampled at the active-to-inactive transition of RESET# for the power-
on configuration. The configuration options are described in Section 4 and in the Pentium® II
Processor Developer’s Manual.
Unless its outputs are tri-stated during power-on configuration, after an active-to-inactive
transition of RESET#, the processor optionally executes its built-in self-test (BIST) and begins
program execution at reset-vector 000FFFF0H or FFFFFFF0H. RESET# must be connected to the
appropriate pins/balls on both agents on the system bus.
RP# (I/O - GTL+)
The RP# (Request Parity) signal is driven by the request initiator and provides parity protection on
ADS# and REQ[4:0]#. RP# should be connected to the appropriate pins/balls on both agents on
the system bus.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 71
A correct parity signal is high if an even number of covered signals are low and low if an odd
number of covered signals are low. This definition allows parity to be high when all covered
signals are high.
RS[2:0]# (I - GTL+)
The RS[2:0]# (Response Status) signals are driven by the response agent (the agent responsible for
completion of the current transaction) and must be connected to the appropriate pins/balls on both
agents on the system bus.
RSP# (I - GTL+)
The RSP# (Response Parity) signal is driven by the response agent (the agent responsible for
completion of the current transaction) during assertion of RS[2:0]#. RSP# provides parity
protection for RS[2:0]#. RSP# should be connected to the appropriate pins/balls on both agents on
the system bus.
A correct parity signal is high if an even number of covered signals are low, and it is low if an odd
number of covered signals are low. During Idle state of RS[2:0]# (RS[2:0]#=000), RSP# is also
high since it is not driven by any agent guaranteeing correct parity.
RSVD (TBD)
The RSVD (Reserved) signal is currently unimplemented but is reserved for future use. Leave this
signal unconnected. Intel recommends that a routing channel for this signal be allocated.
RTTIMPEDP (Analog)
The RTTIMPEDP (RTT Impedance/PMOS) signal is used to configure the on-die GTL+
termination. Connect the RTTIMPEDP signal to VSS with a 56.2-Ω, 1% resistor.
SLP# (I - 1.5V Tolerant)
The SLP# (Sleep) signal, when asserted in the Stop Grant state, causes the processor to enter the
Sleep state. During the Sleep state, the processor stops providing internal clock signals to all units,
leaving only the Phase-Locked Loop (PLL) still running. The processor will not recognize snoop
and interrupts in the Sleep state. The processor will only recognize changes in the SLP#,
STPCLK# and RESET# signals while in the Sleep state. If SLP# is deasserted, the processor exits
Sleep state and returns to the Stop Grant state in which it restarts its internal clock to the bus and
APIC processor units.
SMI# (I - 1.5V Tolerant)
The SMI# (System Management Interrupt) is asserted asynchronously by system logic. On
accepting a System Management Interrupt, the processor saves the current state and enters System
Management Mode (SMM). An SMI Acknowledge transaction is issued, and the processor begins
program execution from the SMM handler.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
72 Datasheet Order Number 283653-001
STPCLK# (I - 1.5V Tolerant)
The STPCLK# (Stop Clock) signal, when asserted, causes the processor to enter a low-power Stop
Grant state. The processor issues a Stop Grant Acknowledge special transaction and stops
providing internal clock signals to all units except the bus and APIC units. The processor
continues to snoop bus transactions and service interrupts while in the Stop Grant state. When
STPCLK# is deasserted, the processor restarts its internal clock to all units and resumes execution.
The assertion of STPCLK# has no affect on the bus clock.
TCK (I - 1.5V Tolerant)
The TCK (Test Clock) signal provides the clock input for the test bus (also known as the test
access port).
TDI (I - 1.5V Tolerant)
The TDI (Test Data In) signal transfers serial test data to the processor. TDI provides the serial
input needed for JTAG support.
TDO (O - 1.5V Tolerant Open-drain)
The TDO (Test Data Out) signal transfers serial test data from the processor. TDO provides the
serial output needed for JTAG support.
TESTHI (I - 1.5V Tolerant)
The TESTHI (Test input High) is used during processor test and needs to be pulled high during
normal operation.
TESTLO[2:1] (I - 1.5V Tolerant)
The TESTLO[2:1] (Test input Low) signals are used during processor test and needs to be pulled
to ground during normal operation.
TESTP (Analog)
The TESTP (Test Point) signals are connected to Vcc and Vss at opposite ends of the die. These
signals can be used to monitor the Vcc level on the die. Route the TESTP signals to test points or
leave them unconnected. Do not short the TESTP signals together.
THERMDA, THERMDC (Analog)
The THERMDA (Thermal Diode Anode) and THERMDC (Thermal Diode Cathode) signals
connect to the anode and cathode of the on-die thermal diode.
TMS (I - 1.5V Tolerant)
The TMS (Test Mode Select) signal is a JTAG support signal used by debug tools.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 73
TRDY# (I - GTL+)
The TRDY# (Target Ready) signal is asserted by the target to indicate that the target is ready to
receive write or implicit write-back data transfer. TRDY# must be connected to the appropriate
pins/balls on both agents on the system bus.
TRST# (I - 1.5V Tolerant)
The TRST# (Test Reset) signal resets the Test Access Port (TAP) logic. The mobile Pentium III
processors do not self-reset during power on; therefore, it is necessary to drive this signal low
during power-on reset.
VID[4:0] (O – Open-drain)
The VID[4:0] (Voltage ID) pins/balls can be used to support automatic selection of power supply
voltages. These pins/balls are not signals, they are either an open circuit or a short to VSS on the
processor substrate. The combination of opens and shorts encodes the voltage required by the
processor. External to pull-ups are required to sense the encoded VID. For processors that have
Intel SpeedStep technology enabled, VID[4:0] encode the voltage required in the battery-
optimized mode. VID[4:0] are needed to cleanly support voltage specification changes on mobile
Pentium III processors. The voltage encoded by VID[4:0] is defined in Table 37. A “1” in this
table refers to an open pin/ball and a “0” refers to a short to VSS. The power supply must provide
the requested voltage or disable itself.
Please note that in order to implement VID on the BGA2 package, some VID[4:0] balls may be
depopulated. For the BGA2 package, a “1” in Table 37implies that the corresponding VID ball is
depopulated, while a “0” implies that the corresponding VID ball is not depopulated.
But on the Micro-PGA2 package, VID[4:0] pins are not depopulated.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
74 Datasheet Order Number 283653-001
Table 37. Voltage Identification Encoding
VID[4:0] VCC
00000 2.00
00001 1.95
00010 1.90
00011 1.85
00100 1.80
00101 1.75
00110 1.70
00111 1.65
01000 1.60
01001 1.55
01010 1.50
01011 1.45
01100 1.40
01101 1.35
01110 1.30
01111 No CPU
10000 1.275
10001 1.250
10010 1.225
10011 1.200
10100 1.175
10101 1.150
10110 1.125
10111 1.100
11000 1.075
11001 1.050
11010 1.025
11011 1.000
11100 0.975
11101 0.950
11110 0.925
11111 No CPU
VREF (Analog)
The VREF (GTL+ Reference Voltage) signal provides a DC level reference voltage for the GTL+
input buffers. A voltage divider should be used to divide VCCT by 2/3. Resistor values of 1.00 kΩ
and 2.00 kΩ are recommended. Decouple the VREF signal with three 0.1-µF high frequency
capacitors close to the processor.
8.2 Signal Summaries
Table 38 through Table 41 list the attributes of the processor input, output, and I/O signals.
Table 38. Input Signals
Name Active Level Clock Signal Group Qualified
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 75
A20M# Low Asynch CMOS Always
BCLK High —System Bus Always
BPRI# Low BCLK System Bus Always
BSEL[1:0] High Asynch Implementation Always
DEFER# Low BCLK System Bus Always
FLUSH# Low Asynch CMOS Always
GHI# Low Asynch CMOS Deep Sleep state
IGNNE# Low Asynch CMOS Always
INIT# Low Asynch System Bus Always
INTR High Asynch CMOS APIC disabled mode
LINT[1:0] High Asynch APIC APIC enabled mode
NMI High Asynch CMOS APIC disabled mode
PICCLK High —APIC Always
PREQ# Low Asynch Implementation Always
PWRGOOD High Asynch Implementation Always
RESET# Low BCLK System Bus Always
RS[2:0]# Low BCLK System Bus Always
RSP# Low BCLK System Bus Always
SLP# Low Asynch Implementation Stop Grant state
SMI# Low Asynch CMOS Always
STPCLK# Low Asynch Implementation Always
TCK High —JTAG
TDI TCK JTAG
TMS TCK JTAG
TRDY# Low BCLK System Bus Response phase
TRST# Low Asynch JTAG
Table 39. Output Signals
Name Active Level Clock Signal Group
FERR# Low Asynch Open-drain
IERR# Low Asynch Open-drain
PRDY# Low BCLK Implementation
TDO High TCK JTAG
VID[4:0] High Asynch Implementation
Table 40. Input/Output Signals (Single Driver)
Name Active Level Clock Signal Group Qualified
A[35:3]# Low BCLK System Bus ADS#, ADS#+1
ADS# Low BCLK System Bus Always
AP[1:0]# Low BCLK System Bus ADS#, ADS#+1
BREQ0# Low BCLK System Bus Always
BP[3:2]# Low BCLK System Bus Always
BPM[1:0]# Low BCLK System Bus Always
D[63:0]# Low BCLK System Bus DRDY#
DBSY# Low BCLK System Bus Always
DEP[7:0]# Low BCLK System Bus DRDY#
DRDY# Low BCLK System Bus Always
LOCK# Low BCLK System Bus Always
REQ[4:0]# Low BCLK System Bus ADS#, ADS#+1
RP# Low BCLK System Bus ADS#, ADS#+1
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
76 Datasheet Order Number 283653-001
Table 41. Input/Output Signals (Multiple Driver)
Name Active Level Clock Signal Group Qualified
AERR# Low BCLK System Bus ADS#+3
BERR# Low BCLK System Bus Always
BINIT# Low BCLK System Bus Always
BNR# Low BCLK System Bus Always
HIT# Low BCLK System Bus Always
HITM# Low BCLK System Bus Always
PICD[1:0] High PICCLK APIC Always
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 77
Appendix A: PLL RLC Filter Specification
A.1 Introduction
All mobile Pentium II and mobile Pentium III processors have internal PLL clock generators,
which are analog in nature and require quiet power supplies for minimum jitter. Jitter is
detrimental to a system; it degrades external I/O timings as well as internal core timings (i.e.
maximum frequency). In mobile Pentium II processors, the power supply filter was specified as
an external LC network. This remains largely the same for the mobile Pentium III processor.
However, due to increased current flow, the value of the inductor has to be reduced, thereby
requiring new components. The general desired topology is shown in Figure 5. Excluded from the
external circuitry are parasitics associated with each component.
A.2 Filter Specification
The function of the filter is two fold. It protects the PLL from external noise through low-pass
attenuation. It also protects the PLL from internal noise through high-pass filtering. In general,
the low-pass description forms an adequate description for the filter.
The AC low-pass specification, with input at VCCT and output measured across the capacitor, is as
follows:
• < 0.2 dB gain in pass band
• < 0.5 dB attenuation in pass band < 1 Hz (see DC drop in next set of requirements)
• 34 dB attenuation from 1 MHz to 66 MHz
• 28 dB attenuation from 66 MHz to core frequency
The filter specification (AC) is graphically shown in Figure 27.
Other requirements:
• Use a shielded type inductor to minimize magnetic pickup
• The filter should support a DC current of at least 30 mA
• The DC voltage drop from VCCT to PLL1 should be less than 60 mV, which in practice implies
series resistance of less than 2Ω. This also means that the pass band (from DC to 1Hz)
attenuation below 0.5 dB is for VCCT = 1.1V and below 0.35 dB for VCCT = 1.5V.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
78 Datasheet Order Number 283653-001
Figure 27. PLL Filter Specifications
0 dB
-28 dB
-34 dB
0.2 dB
forbidden
zone
x dB
forbidden
zone
1 MHz 66 MHz fcorefpeak1 HzDC
passband high frequency
band
x = 20.log[(Vcct-60 mV)/
Vcct]
NOTES:
1. Diagram is not to scale
2. No specification for frequencies beyond fcore.
3. Fpeak, if existent, should be less than 0.05 MHz.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 79
A.3 Recommendation for Mobile Systems
The following LC components are recommended. The tables will be updated as other suitable
components and specifications are identified.
Table 42. PLL Filter Inductor Recommendations
Inductor Part Number Value Tol SRF Rated I DCR Min Damping R needed
L1 TDK MLF2012A4R7KT 4.7 µH10% 35 MHz 30 mA 0.56Ω (1Ω
max) 0Ω
L2 Murata LQG21N4R7K10 4.7 µH10% 47 MHz 30 mA 0.7Ω (+/-
50%) 0Ω
L3 Murata LQG21C4R7N00 4.7 µH30% 35 MHz 30 mA 0.3Ω max 0.2Ω (assumed)
NOTE: Minimum damping resistance is calculated from 0.35Ω – DCRmin. From vendor provided data, L1 and L2 DCRmin
is 0.4 Ω and 0.5 Ω respectively, qualifying them for zero required trace resistance. DCRmin for L3 is not known
and is assumed to be 0.15 Ω. There may be other vendors who might provide parts of equivalent characteristics
and the OEMs should consider doing their own testing for selecting their own vendors.
Table 43. PLL Filter Capacitor Recommendations
Capacitor Part Number Value Tolerance ESL ESR
C1 Kemet T495D336M016AS 33 µF20% 2.5 nH 0.225Ω
C2 AVX TPSD336M020S0200 33 µF20% unknown 0.2Ω
NOTE: There may be other vendors who might provide parts of equivalent characteristics and the OEMs should consider
doing their own testing for selecting their own vendors.
Table 44. PLL Filter Resistor Recommendations
Resistor Part Number Value Tolerance Power
R1 various 1Ω10% 1/16W
To satisfy damping requirements, total series resistance in the filter (from VCCT to the top plate of
the capacitor) must be at least 0.35Ω. This resistor can be in the form of a discrete component, or
routing, or both. For example, if the picked inductor has minimum DCR of 0.25Ω, then a routing
resistance of at least 0.10Ω is required. Be careful not to exceed the maximum resistance rule
(2Ω). For example, if using discrete R1, the maximum DCR of the L should be less than 2.0 - 1.1
= 0.9Ω, which precludes using L2 and possibly L1.
Other routing requirements:
• The capacitor should be close to the PLL1 and PLL2 pins, with less than 0.1Ω per route (These
routes do not count towards the minimum damping resistance requirement).
• The PLL2 route should be parallel and next to the PLL1 route (minimize loop area).
• The inductor should be close to the capacitor; any routing resistance should be inserted
between VCCT and the inductor.
• Any discrete resistor should be inserted between VCCT and the inductor.
A.4 Comments
• A magnetically shielded inductor protects the circuit from picking up external flux noise. This
should provide better timing margins than with an unshielded inductor.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage 700 MHz,
Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
80 Datasheet Order Number 283653-001
• A discrete or routed resistor is required because the LC filter by nature has an under-damped
response, which can cause resonance at the LC pole. Noise amplification at this band, although
not in the PLL-sensitive spectrum, could cause a fatal headroom reduction for analog circuitry.
The resistor serves to dampen the response. Systems with tight space constraints should
consider a discrete resistor to provide the required damping resistance. Too large of a damping
resistance can cause a large IR drop, which means less analog headroom and lower frequency.
• Ceramic capacitors have very high self-resonance frequencies, but they are not available in
large capacitance values. A high self-resonant frequency coupled with low ESL/ESR is crucial
for sufficient rejection in the PLL and high frequency band. The recommended tantalum
capacitors have acceptably low ESR and ESL.
• The capacitor must be close to the PLL1 and PLL2 pins, otherwise the value of the low ESR
tantalum capacitor is wasted. Note the distance constraint should be translated from the 0.1-Ω
requirement.
The mobile Pentium II processor LC filter cannot be used with the mobile Pentium III processor. The
larger inductor of the old LC filter imposes a lower current rating. Due to increased current requirements for
the mobile Pentium III processor, a lower value inductor is required.
Mobile Intel® Pentium® III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,
900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage
700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz
Order Number 283653-001 Datasheet 81
Appendix B: Intel Mobile Voltage Positioning
(IMVP) for the Mobile Pentium III Processor
B.1 Introduction
Intel Mobile Voltage Positioning (IMVP) is an advanced voltage regulation technology for Intel's
high performance mobile processors. Thermal design is critical to compete in the mobile high
performance segments and IMVP technology will provide designers with a competitive edge.
Utilizing IMVP technology for microprocessor voltage regulator designs will significantly reduce
CPU power, which will provide thermal benefits needed for thin and light performance systems.
IMVP technology offers the following two design options:
• Design for cost optimization
• Design for maximum CORE power reduction
B.2 Reference Documents
Intel® Mobile Voltage Positioning Voltage Regulation Controller Application Note, Rev 1.0 (OR-
2101 Contact your Intel Field Sales Representative)
Intel® SpeedStepTM Technology Voltage Regulator Specification, Rev 1.70 (OR-2555 Contact your
Intel Field Sales Representative)
