Continental Device India Limited An ISO/TS16949 and ISO 9001 Certified Company BC556, A, B, C BC557, A, B, C BC558, A, B, C TO-92 Plastic Package PNP SILICON PLANAR EPITAXIAL TRANSISTORS General Purpose Transistors ABSOLUTE MAXIMUM RATINGS(Ta=25 deg C unless otherwise specified) DESCRIPTION SYMBOL BC556 BC557 BC558 UNITS 65 80 80 5 45 50 50 5 100 200 200 200 500 30 30 30 5 V V V V mA mA mA mA mW Collector Emitter Voltage Collector Emitter Voltage Collector Base Voltage Emitter Base Voltage Collector Current Continuous Peak Base Current - Peak Emitter Current - Peak Collector Power Dissipation VCEO VCES VCBO VEBO IC ICM IBM IEM PTA Ta =25 deg C Operating And Storage Junction Tj, Tstg -55 to +150 Rth(j-a) 250 C Temperature Range THERMAL RESISTANCE Junction to ambient C/W ELECTRICAL CHARACTERISTICS (Ta=25 deg C Unless Otherwise Specified) DESCRIPTION SYMBOL TEST CONDITION MIN TYP MAX UNITS Collector Emitter Voltage BC556 VCEO IC=2mA,IB=0 BC557 BC558 Continental Device India Limited Datasheet 65 V 45 30 V V Page 1 of 5 PNP SILICON PLANAR EPITAXIAL TRANSISTORS DESCRIPTION Collector Base Voltage SYMBOL BC556 VCBO TEST CONDITION IC=100uA,IE=0 BC557 BC558 Emitter Base Voltage Collector Cut off Current VEBO IE=100uA, IC=0 ICBO VCB =30V, IE = 0 VCB =30V, IE = 0 BC556, A, B, C BC557, A, B, C BC558, A, B, C TO-92 Plastic Package MIN TYP MAX UNITS 80 V 50 30 V V 5 V 15 4 nA uA 15 15 15 4 4 4 nA nA nA uA uA uA Tj= 150 deg C Collector Cut off Current BC556 BC557 BC558 BC556 BC557 BC558 ICES VCE =80V VCE =50V VCE =30V VCE =80V,Tj=125O C VCE =50V,Tj=125O C VCE =30V,Tj=125O C 0.2 0.2 0.2 A hFE VCE =5V,IC=10uA 90 DC Current Gain B C BC556 150 270 75 475 BC557, BC558 75 800 A B C 110 200 420 A hFE hFE VCE =5V,IC=2mA VCE =5V,IC=100mA B C Continental Device India Limited 180 290 500 220 450 800 120 200 400 Datasheet Page 2 of 5 PNP SILICON PLANAR EPITAXIAL TRANSISTORS DESCRIPTION SYMBOL Collector Emitter Saturation Voltage VCE(sat) TEST CONDITION Base Emitter Saturation Voltage Base Emitter On Voltage DYNAMICS CHARACTERISTICS TYP MAX UNITS IC=10mA,IB=0.5mA IC=100mA,IB=5mA 0.09 0.25 0.3 0.65 V V VBE(sat) IC=10mA,IB=0.5mA IC=100mA,IB=5mA 0.70 0.90 VBE(on) IC=2mA,VCE =5V IC=10mA,VCE =5V 0.55 0.66 0.70 0.82 V V TEST CONDITION MIN TYP MAX UNITS SYMBOL Transition Frequency BC556, A, B, C BC557, A, B, C BC558, A, B, C TO-92 Plastic Package fT MIN IC=10mA, VCE =5V f=100MHz Collector output Capacitance Noise Figure V V 150 Ccbo VCB =10V, f =1MHZ NF VCE =5V,IC=0.2mA RS=2K,f=1KHZ, B =200HZ hf e VCE =5V,IC=2mA 220 f=1KHz 330 600 2 MHz 6 pF 10 dB k Small Signal Current Gain A B C Input Impedance A hie B C VCE =5V,IC=2mA 1.6 2.7 4.5 f=1KHz 3.2 6.0 4.5 8.7 8.5 15 Voltage Feedback A hre B C VCE =5V,IC=2mA 1.5 x10 f=1KHz 2.0 3.0 VCE =5V,IC=2mA 18 30 f=1KHz 30 60 60 110 Output Admittance A B C Continental Device India Limited hoe Datasheet u MHO Page 3 of 5 BC556, A, B, C BC557, A, B, C BC558, A, B, C TO-92 Plastic Package B A TO-92 Transistors on Tape and Ammo Pack 1 2 3 Ammo Pack Style MECHANICAL DATA h T Adhesive Tape on Top Side P h A1 (p) LABEL A K H1 D FE E Carrier Strip FLAT SIDE 8.2" W2 H0 L W o W 1 W D A A PIN CONFIGURATION 1. COLLECTOR 2. BASE 3. EMITTER All diminsions in mm. C H F 1 2 3 B E t F1 F2 F 13" P2 Po ITEM DIM MIN. MAX. A 4.32 5.33 B 4.45 5.20 C 3.18 4.19 D 0.41 0.55 E 0.35 0.50 F 1. 7 Do 7" All dimensions in mm unless specified otherwise SEC AA G F C E D t1 5 DEG G 1.14 1.40 H 1.14 1.53 K 12.70 -- SYMBOL BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT FEED HOLE PITCH A1 A T P Po FEED HOLE CENTRE TO COMPONENT CENTRE P2 DISTANCE BETWEEN OUTER LEADS COMPONENT ALIGNMENT TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION F h W Wo W1 HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCEF1, W2 Ho H1 L Do t F2 CLINCH HEIGHT PULL - OUT FORCE H2 (P) Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack SPECIFICATION REMARKS MIN. NOM. MAX. TOL . 4.0 4.8 4.8 5.2 4.2 3.9 12.7 1 12.7 0.3 CUMULATIVE PITCH ERROR 1.0 mm/20 PITCH 6.35 0.4 TO BE MEASURED AT BOTTOM OF CLINCH +0.6 5.08 -0.2 0 1 AT TOP OF BODY 18 0.5 6 0.2 9 +0.7 -0.5 0.5 0.2 16 0.5 23.25 11.0 4 0.2 1.2 t1 0.3 - 0.6 2.54 +0.4 -0.1 3 6N NOTES 1. MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm. 2. MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20 PITCHES. 3. HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO EXPOSURE OF ADHESIVE. 4. NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED. 5. A TAPE TRAILER, HAVING AT LEAST THREE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT. 6. SPLICES SHALL NOT INTERFERE WITH THE SPROCKET FEED HOLES. Packing Detail PACKAGE STANDARD PACK Continental Device India Limited INNER CARTON BOX Datasheet OUTER CARTON BOX Page 4 of 5 Notes BC556, A, B, C BC557, A, B, C BC558, A, B, C TO-92 Plastic Package Disclaimer The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as to confirm that the Device(s) meet functionality parameters for your application. The information furnished on the CDIL Web Site/CD is believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for use in life saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s). CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice. CDIL is a registered Trademark of Continental Device India Limited C-120 Naraina Industrial Area, New Delhi 110 028, India. Telephone + 91-11-2579 6150, 5141 1112 Fax + 91-11-2579 5290, 5141 1119 emai@cdil.com www.cdilsemi.com Continental Device India Limited Datasheet Page 5 of 5